AI4AVSummary
Sharp PN-M/PN-P series LCD monitor external control spec covering the SHARP M/P Series PN-M432 and siblings. The monitor supports RS-232C remote control (9600bps, 8N1) and LAN (TCP/IP) control on fixed port 7142. Commands use a framed protocol (SOH header, STX/ETX message, BCC check code, CR delimiter) with two command families: VCP (virtual control panel get/set parameter) and CTL (discrete command messages).
Transport
protocols:
- serial
- tcp
serial:
baud_rate: 9600
data_bits: 8
parity: none
stop_bits: 1
flow_control: null # UNRESOLVED: flow control not stated in source
addressing:
port: 7142 # LAN control, fixed
auth:
type: none # inferred: no auth procedure in source
Traits
traits:
- powerable # inferred from CTL-C203-D6 power control command
- queryable # inferred from VCP get-parameter and CTL-01D6 power status read
- levelable # inferred from VCP volume / backlight / contrast set commands
Actions
# Protocol framing (applies to ALL commands): SOH(01h) | Reserved '0'(30h) |
# Destination | Source '0'(30h) | MsgType | MsgLen | STX(02h) | Message | ETX(03h) |
# BCC (XOR of bytes from Reserved through ETX) | CR(0Dh).
# MsgType: A=Command, B=Cmd reply, C=Get param, D=Get reply, E=Set param, F=Set reply.
# All numeric bytes are ASCII-encoded hex (e.g. byte 3Ah -> '3','A' = 33h,41h).
# Controller Source ID must be '0'(30h). Destination = monitor address (1->'A', ALL->'*').
# Per source: wait for reply before next command. After Power On/Off wait 15s; after
# Input / PIP Input / Auto Setup / Factory Reset wait 10s. LAN disconnects after 15min idle.
# --- CTL commands ---
- id: power_control
label: Power Control
kind: action
command: "C203D6" # CTL-C203-D6, message bytes 43H 32H 30H 33H 44H 36H
params:
- name: power_mode
type: string
description: Power mode value (4 ASCII hex chars)
values:
- "0001": ON
- "0002": Do not set
- "0003": Do not set
- "0004": OFF (same as IR power off)
- id: power_status_read
label: Power Status Read
kind: query
command: "01D6" # CTL-01D6 get power status: 30H,31H,44H,36H
params: []
- id: save_current_settings
label: Save Current Settings
kind: action
command: "0C" # CTL-0C, bytes 30H 43H
params: []
- id: get_timing_report
label: Get Timing Report
kind: query
command: "07" # CTL-07, bytes 30H 37H; reply command code "4E"(34H 45H)
params: []
- id: input_name_set
label: Input Name Set
kind: action
command: "CA0400" # CTL-CA04-00 # UNRESOLVED: section 7 payload not in source excerpt
params:
- name: name
type: string
description: "UNRESOLVED: input name payload per section 7 (not in source excerpt)"
- id: input_name_set_alt
label: Input Name Set (alt)
kind: action
command: "CA0401" # CTL-CA04-01 # UNRESOLVED: section 7 payload not in source excerpt
params:
- name: name
type: string
description: "UNRESOLVED: input name payload per section 7 (not in source excerpt)"
- id: name_reset
label: Name Reset
kind: action
command: "CA0402" # CTL-CA04-02 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: mac_address
label: MAC Address
kind: query
command: "C220" # CTL-C220 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: power_save_set_00
label: Power Save Set
kind: action
command: "CA0B00" # CTL-CA0B-00 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: power_save_set_01
label: Power Save Set (alt)
kind: action
command: "CA0B01" # CTL-CA0B-01 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: power_save_time_setting_02
label: Power Save Time Setting
kind: action
command: "CA0B02" # CTL-CA0B-02 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: power_save_time_setting_03
label: Power Save Time Setting (alt)
kind: action
command: "CA0B03" # CTL-CA0B-03 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: password_secure_mode
label: Password / Secure Mode
kind: action
command: "C21D" # CTL-C21D (Password, Start-Up Lock, Control Lock) # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: lock_settings_select
label: Lock Settings Select
kind: action
command: "CA32" # CTL-CA32 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: lock_settings_select_alt
label: Lock Settings Select (alt)
kind: action
command: "CA33" # CTL-CA33 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: model_read
label: Monitor Model
kind: query
command: "C217" # CTL-C217 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: serial_read
label: Monitor Serial
kind: query
command: "C216" # CTL-C216 # UNRESOLVED: section 7 payload not in source excerpt
params: []
- id: firmware_revision_read
label: Firmware Revision
kind: query
command: "C03F" # CTL-C03F # UNRESOLVED: section 7 payload not in source excerpt
params: []
# --- VCP commands (each VCP-<page>-<code> supports get (MsgType C) and set (MsgType E)) ---
# Set message payload: STX | OP Code Page (Hi,Lo) | OP Code (Hi,Lo) | Set value (16-bit, MSB..LSB) | ETX
- id: input_select
label: Input Select
kind: action
command: "VCP-00-60"
params:
- name: input
type: string
description: Input source (4 ASCII hex chars)
values:
- "000D": OPTION
- "000F": DisplayPort
- "0011": HDMI1
- "0012": HDMI2
- "0088": COMPUTE MODULE
- "0089": USB-C
- id: auto_input_change
label: Auto Input Change
kind: action
command: "VCP-02-40"
params:
- name: mode
type: string
values:
- "0000": FIRST DETECT
- "0001": LAST DETECT
- "0002": NONE
- "0004": CUSTOM DETECT
- id: input_priority_1
label: Input Priority 1
kind: action
command: "VCP-10-2E"
params:
- name: input
type: string
values:
- "000D": OPTION
- "000F": DisplayPort
- "0010": HDMI1
- "0012": HDMI2
- "0088": COMPUTE MODULE
- "0089": USB-C
- id: input_priority_2
label: Input Priority 2
kind: action
command: "VCP-10-2F"
params:
- name: input
type: string
values:
- "000D": OPTION
- "000F": DisplayPort
- "0010": HDMI1
- "0012": HDMI2
- "0088": COMPUTE MODULE
- "0089": USB-C
- id: input_priority_3
label: Input Priority 3
kind: action
command: "VCP-10-30"
params:
- name: input
type: string
values:
- "000D": OPTION
- "000F": DisplayPort
- "0010": HDMI1
- "0012": HDMI2
- "0088": COMPUTE MODULE
- "0089": USB-C
- id: displayport_version
label: DisplayPort Version
kind: action
command: "VCP-10-F2"
params:
- name: version
type: string
values:
- "0001": "1.1a"
- "0002": "1.2"
- "0003": "1.4"
- id: dp_sst_mst
label: DisplayPort SST/MST
kind: action
command: "VCP-11-67"
params:
- name: mode
type: string
values:
- "0001": SST
- "0002": MST
- id: hdcp_version
label: HDCP Version
kind: action
command: "VCP-11-D2"
params:
- name: version
type: string
values:
- "0001": HDCP1.4
- "0002": HDCP2.2
- id: hdr_enable
label: HDR
kind: action
command: "VCP-11-FD"
params:
- name: state
type: string
values:
- "0001": DISABLE
- "0002": ENABLE
- id: hdmi_mode
label: HDMI Mode
kind: action
command: "VCP-11-68"
params:
- name: mode
type: string
values:
- "0001": Mode1 (1.4)
- "0002": Mode2 (2.0)
- id: overscan
label: Overscan
kind: action
command: "VCP-02-E3"
params:
- name: mode
type: string
values:
- "0001": OFF
- "0002": ON
- "0003": Auto
- id: video_range
label: Video Range
kind: action
command: "VCP-10-40"
params:
- name: range
type: string
values:
- "0001": LIMITED
- "0002": FULL
- "0003": AUTO
- id: colorimetry
label: Colorimetry
kind: action
command: "VCP-11-A3"
params:
- name: mode
type: string
values:
- "0001": AUTO
- "0002": RGB
- "0003": YCbCr (BT.601)
- "0004": YCbCr (BT.709)
- "0005": YCbCr (BT.2020)
- id: cec
label: CEC
kind: action
command: "VCP-11-76"
params:
- name: mode
type: string
values:
- "0001": OFF
- "0002": MODE1 (ON)
- "0003": MODE2
- id: cec_power_control_link
label: CEC Power Control Link
kind: action
command: "VCP-11-77"
params:
- name: state
type: string
values:
- "0001": DISABLE
- "0002": ENABLE
- id: cec_audio_receiver
label: CEC Audio Receiver
kind: action
command: "VCP-11-78"
params:
- name: state
type: string
values:
- "0001": DISABLE
- "0002": ENABLE
- id: background_color
label: Background Color
kind: action
command: "VCP-02-DF"
params:
- name: level
type: integer
description: "0000H - 0064H (Black - White)"
- id: reset
label: Reset
kind: action
command: "VCP-02-CB" # same opcode used for multiple reset scopes; value selects scope
params:
- name: reset_type
type: string
description: Reset scope (4 ASCII hex chars)
values:
- "0013": Input
- "0004": Audio
- "000F": Slot
- "0010": Network
- "0001": All (Factory Reset)
- id: picture_mode
label: Picture Mode
kind: action
command: "VCP-02-1A"
params:
- name: mode
type: string
values:
- "0003": HIGHBRIGHT
- "0008": CUSTOM1
- "001C": RETAIL
- "001D": CONFERENCING
- "001E": TRANSPORTATION
- "001F": NATIVE
- id: backlight
label: Backlight
kind: action
command: "VCP-00-10"
params:
- name: level
type: integer
description: "0000H - 0064H (Dark - Bright)"
- id: video_black_level
label: Video Black Level
kind: action
command: "VCP-00-92"
params:
- name: level
type: integer
description: "0000H - 0064H (To Dark - To Bright)"
- id: gamma
label: Gamma
kind: action
command: "VCP-02-68"
params:
- name: gamma
type: string
values:
- "0001": NATIVE
- "0004": "2.2"
- "0005": DICOM SIM.
- "0006": PROGRAMABLE1
- "0007": S GAMMA
- "0008": "2.4"
- "0009": Custom
- "000B": sRGB
- "000C": L STAR
- "000D": PROGRAMMABLE2
- "000E": PROGRAMMABLE3
- "000F": Bt1886
- "0010": HDR-Hybrid Log
- "0011": HDR-ST2084 (PQ)
- id: auto_hdr_select
label: Auto HDR Select
kind: action
command: "VCP-11-B2"
params:
- name: state
type: string
values:
- "0001": ON
- "0002": OFF
- id: color_vcp_021f
label: Color (VCP-02-1F)
kind: action
command: "VCP-02-1F"
params:
- name: level
type: integer
description: "0000H - 0064H (Pale - To Deep)"
- id: color_vcp_008a
label: Color (VCP-00-8A)
kind: action
command: "VCP-00-8A"
params:
- name: level
type: integer
description: "0000H - 0064H (Pale - To Deep)"
- id: color_temperature_multiplier
label: Color Temperature Multiplier
kind: action
command: "VCP-00-0C"
params:
- name: multiplier
type: integer
description: "0 - (max value: 0001h-FFFFh); 0 -> 3000K base; >0 = multiplier of increment (VCP-00-0B) added to base 3000K"
- id: color_temperature
label: Color Temperature
kind: action
command: "VCP-00-54"
params:
- name: kelvin
type: integer
description: "0000H - 004AH (2600K - 10000K), step 100K"
- id: color_temperature_preset
label: Color Temperature Preset
kind: action
command: "VCP-00-14"
params:
- name: preset
type: string
values:
- "0002": Display native (NATIVE)
- "0009": 10000K
- "000B": User1 (CUSTOM)
- id: r_gain
label: R Gain
kind: action
command: "VCP-00-16"
params:
- name: level
type: integer
description: "0000H - 0064H (Dark - Bright)"
- id: g_gain
label: G Gain
kind: action
command: "VCP-00-18"
params:
- name: level
type: integer
description: "0000H - 0064H (Dark - Bright)"
- id: b_gain
label: B Gain
kind: action
command: "VCP-00-1A"
params:
- name: level
type: integer
description: "0000H - 0064H (Dark - Bright)"
- id: contrast
label: Contrast
kind: action
command: "VCP-00-12"
params:
- name: level
type: integer
description: "0000H - 0064H (Low - High)"
- id: audio_mode
label: Audio Mode
kind: action
command: "VCP-11-D8"
params:
- name: mode
type: string
values:
- "0001": RETAIL
- "0002": CONFERENCING
- "0003": HIGHBRIGHT
- "0004": TRANSPORTATION
- "0005": CUSTOM
- "0007": NATIVE
- id: volume
label: Volume
kind: action
command: "VCP-00-62"
params:
- name: level
type: integer
description: "0000H - 0064H (Whisper - Loud)"
- id: stereo_mono
label: Stereo/Mono
kind: action
command: "VCP-00-94"
params:
- name: mode
type: string
values:
- "0001": Monaural
- "0002": Stereo
- id: balance
label: Balance
kind: action
command: "VCP-00-93"
params:
- name: level
type: integer
description: "0000H - 0032H (To Left - To Right)"
- id: surround
label: Surround
kind: action
command: "VCP-02-34"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: treble
label: Treble
kind: action
command: "VCP-00-8F"
params:
- name: level
type: integer
description: "0000H - 0064H (De-emphasized - Emphasized)"
- id: bass
label: Bass
kind: action
command: "VCP-00-91"
params:
- name: level
type: integer
description: "0000H - 0064H (De-emphasized - Emphasized)"
- id: line_out
label: Line Out
kind: action
command: "VCP-10-81"
params:
- name: mode
type: string
values:
- "0001": FIXED
- "0002": VARIABLE
- id: audio_input
label: Audio Input
kind: action
command: "VCP-02-2E"
params:
- name: input
type: string
values:
- "0004": HDMI1
- "0006": Option
- "0007": DisplayPort
- "000A": HDMI2
- "000E": COMPUTE MODULE
- "000F": USB-C
- id: internal_speaker
label: Internal Speaker
kind: action
command: "VCP-11-BB"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: auto_shutdown
label: Auto Shutdown
kind: action
command: "VCP-11-B7"
params:
- name: state
type: string
values:
- "0001": DISABLE
- "0002": ENABLE
- id: shutdown_signal
label: Shutdown Signal
kind: action
command: "VCP-11-81"
params:
- name: state
type: string
values:
- "0001": DISABLE
- "0002": ENABLE
- id: ir_signal
label: IR Signal
kind: action
command: "VCP-11-7F"
params:
- name: state
type: string
values:
- "0001": DISABLE
- "0002": ENABLE
- id: monitor_control
label: Monitor Control
kind: action
command: "VCP-11-80"
params:
- name: state
type: string
values:
- "0001": DISABLE
- "0002": ENABLE
- id: wdt_enable
label: WDT Enable/Disable
kind: action
command: "VCP-11-9B"
params:
- name: state
type: string
values:
- "0001": DISABLE
- "0002": ENABLE
- id: wdt_control
label: WDT Control/Status
kind: action
command: "VCP-11-9E"
params:
- name: action
type: string
description: "Set: 0000H=No mean, 0001H=Reset WDT, 0002H=Stop. Get: 0000H=disabled, 0001H=running, 0002H=stopped"
values:
- "0000": No mean (Set) / WDT is disabled (Get)
- "0001": Reset WDT (Set) / WDT is running (Get)
- "0002": Stop (Set) / WDT is stopped (Get)
- id: wdt_startup_time
label: WDT Start Up Time
kind: action
command: "VCP-11-9C"
params:
- name: seconds
type: integer
description: "0001H - 001EH (10 - 300)"
- id: wdt_period_time
label: WDT Period Time
kind: action
command: "VCP-11-9D"
params:
- name: seconds
type: integer
description: "0001H - 001EH (10 - 300)"
- id: slot_power
label: Slot Power
kind: action
command: "VCP-10-41"
params:
- name: mode
type: string
values:
- "0001": OFF
- "0002": ON
- "0003": AUTO
- id: network_interface_display
label: Network Interface Display
kind: action
command: "VCP-11-CF"
params:
- name: state
type: string
values:
- "0001": Disable
- "0002": Enable
- id: network_interface_compute_module
label: Network Interface Compute Module
kind: action
command: "VCP-11-D1"
params:
- name: state
type: string
values:
- "0001": Disable
- "0002": Enable
- id: http_server
label: HTTP Server
kind: action
command: "VCP-11-F0"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: https_server
label: HTTPS Server
kind: action
command: "VCP-13-22"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: pc_control
label: PC Control
kind: action
command: "VCP-11-F4"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: pc_control_secure
label: PC Control Secure
kind: action
command: "VCP-13-23"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: search
label: Search
kind: action
command: "VCP-13-24"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: lan_daisy_chain
label: LAN Daisy Chain
kind: action
command: "VCP-13-25"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: amx_beacon
label: AMX Beacon
kind: action
command: "VCP-11-F2"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: crestron
label: Crestron
kind: action
command: "VCP-11-F3"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: snmp
label: SNMP
kind: action
command: "VCP-13-26"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: icmp
label: ICMP
kind: action
command: "VCP-13-27"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: ip_mac_filter
label: IP/MAC Filter
kind: action
command: "VCP-13-28"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: naviset_secure
label: NAVISET Secure
kind: action
command: "VCP-13-3A"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: ieee802_1x
label: IEEE802.1X
kind: action
command: "VCP-13-29"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: power_save_message
label: Power Save Message
kind: action
command: "VCP-11-7B"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: quick_start
label: Quick Start
kind: action
command: "VCP-11-EA"
params:
- name: state
type: string
values:
- "0001": DISABLE
- "0002": ENABLE
- id: fan_control
label: Fan Control
kind: action
command: "VCP-02-7D"
params:
- name: mode
type: string
values:
- "0001": AUTO (no offset)
- "0002": Forced ON
- id: fan_speed
label: Fan Speed
kind: action
command: "VCP-10-3F"
params:
- name: speed
type: string
values:
- "0001": HIGH
- "0002": LOW
- id: fan_status_select
label: Fan Status Select
kind: action
command: "VCP-02-7A"
params:
- name: fan
type: string
description: Selects which fan to read via VCP-02-7B
values:
- "0001": Fan#1
- "0002": Fan#2
- "0003": Fan#3
- "0004": Fan#1+Fan#2
- "0005": Fan#1+Fan#2+Fan#3
- id: fan_status_value
label: Fan Status Value
kind: query
command: "VCP-02-7B"
params:
- name: status
type: string
values:
- "0000": OFF
- "0001": ON
- "0002": Error
- id: temperature_sensor_select
label: Temperature Sensor Select
kind: action
command: "VCP-02-78"
params:
- name: sensor
type: string
values:
- "0001": Sensor#1
- "0002": Sensor#2
- "0003": Sensor#3
- id: temperature_value
label: Temperature Value
kind: query
command: "VCP-02-79"
params:
- name: value
type: integer
description: "0000H - FFFFH"
- id: power_on_delay
label: Power On Delay
kind: action
command: "VCP-02-D8"
params:
- name: seconds
type: integer
description: "0000H: OFF; 0001H - 0032H (1sec - 50sec)"
- id: link_to_id
label: Link To ID
kind: action
command: "VCP-10-BC"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: ext_control_rs232c_port
label: External Control RS-232C Port
kind: action
command: "VCP-13-2A"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: ext_control_usb_port
label: External Control USB Port
kind: action
command: "VCP-13-2B"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
- id: monitor_id
label: Monitor ID
kind: action
command: "VCP-02-3E"
params:
- name: id
type: integer
description: "0001H - 0064H"
- id: group_id
label: Group ID
kind: action
command: "VCP-10-7F"
params:
- name: bitmask
type: integer
description: "0000H - 03FFH; bit0=A, bit1=B, bit2=C, bit3=D, bit4=E, bit5=F, bit6=G, bit7=H, bit8=I, bit9=J"
- id: command_transfer
label: Command Transfer
kind: action
command: "VCP-11-4F"
params:
- name: state
type: string
values:
- "0001": OFF
- "0002": ON
Feedbacks
# Result codes are returned in reply messages (MsgType B/D/F):
# 00h: No Error
# 01h: Unsupported operation with this monitor or unsupported under current condition
- id: power_state
type: enum
values: [ON, Stand-by, Reserved, OFF]
# CTL-01D6 reply current power mode: 0001=ON, 0002=Stand-by(power save), 0003=Reserved, 0004=OFF
- id: timing_status
type: string
description: "CTL-07 reply: SS byte (bit7 out-of-range, bit6 unstable, bit1 H-sync polarity, bit0 V-sync polarity), H Freq (0.01kHz), V Freq (0.01Hz)"
- id: get_param_reply
type: string
description: "VCP get reply (MsgType D): Result | OP Code Page | OP Code | Type (00=Set, 01=Momentary) | Max value | Current Value"
- id: set_param_reply
type: string
description: "VCP set reply (MsgType F): Result | OP Code Page | OP Code | Type | Max value | Requested Setting Value"
- id: null_message
type: string
description: "CTL-BE (NULL message): returned on timeout (default 10s), unsupported message type, BCC error, or not ready/not expected. Returned during execution of Power ON/OFF, Auto Setup, Input, PIP Input, Factory reset."
Variables
# Settable parameters are represented as Actions above (each VCP code is get/set).
# No additional independent variables defined.
# UNRESOLVED: none beyond action params
Events
# No unsolicited notifications documented; monitor replies only to controller requests.
# NULL message (CTL-BE) is a reply, not an unsolicited event.
# UNRESOLVED: none
Macros
# UNRESOLVED: no multi-step sequences described in source
Safety
confirmation_required_for: []
interlocks:
- "After Power On / Power Off, controller must wait 15 seconds before sending next command."
- "After Input / PIP Input / Auto Setup / Factory Reset, controller must wait 10 seconds before sending next command."
- "Controller must wait for a reply packet before sending the next command."
- "LAN control: monitor disconnects if no packet received for 15 minutes; controller must re-connect to resume control."
# UNRESOLVED: no explicit safety/hazard interlock procedures stated beyond communication timing.
Notes
- Framed binary-over-ASCII protocol. All numeric data bytes are ASCII-encoded hex (e.g. byte value 3Ah is sent as ASCII '3','A'). BCC check code = XOR of all bytes from Reserved ('0') through ETX, inclusive. Delimiter is CR (0Dh).
- Two command families: VCP (get/set a parameter by OP code page + OP code; MsgType C/E,
reply D/F) and CTL (discrete command messages; MsgType A, reply B). VCP codes use the
VCP-<page>-<code>notation; CTL codes use theCTL-<...>notation. - Destination address maps to Monitor ID (1->'A' 41h ... 100->A4h, ALL->'*' 2Ah) or Group ID (A->'1' ... J->':'). Reply sets destination to the controller ('0') and source to the monitor's own ID.
- Many CTL commands (INPUT NAME, NAME RESET, MAC ADDRESS, POWER SAVE, TIME SETTING, PASSWORD/SECURE MODE, LOCK SETTINGS, MODEL, SERIAL, FIRMWARE) are referenced to "section 7" which was not present in the refined source excerpt; their detailed payloads are marked UNRESOLVED in the Actions section.
Provenance
source_domains:
- business.sharpusa.com
- smj.jp.sharp
source_urls:
- https://business.sharpusa.com/portals/0/downloads/manuals/pn-pxx6_pn-mxx2_n_format_external_control_manual.pdf
- https://smj.jp.sharp/bs/lcd-display/lineup/pnm/download_files/sharp-lcd_display_pnm2-pnp6-series_external-control_manual.pdf
- https://business.sharpusa.com/product-downloads
retrieved_at: 2026-08-05T06:06:39.004Z
last_checked_at: 2026-08-05T08:41:25.572Z
Verification Summary
verdict: verified
checked_at: 2026-08-05T08:41:25.572Z
matched_actions: 99
action_count: 99
confidence: medium
summary: "All 99 spec actions map to wire tokens present verbatim in source; transport (9600/8/N/1, port 7142) is source-supported. (11 unresolved item(s) noted in Known Gaps.)"
Known Gaps
- "firmware version compatibility not stated in source"
- "section 7 referenced for many CTL commands (INPUT NAME, MAC ADDRESS,"
- "flow control not stated in source"
- "section 7 payload not in source excerpt"
- "input name payload per section 7 (not in source excerpt)\""
- "none beyond action params"
- none
- "no multi-step sequences described in source"
- "no explicit safety/hazard interlock procedures stated beyond communication timing."
- "serial flow control not stated in source"
- "section 7 CTL command payloads (INPUT NAME, MAC ADDRESS, PASSWORD, LOCK,"
From the AI4AV catalog (https://ai4av.net) · ODbL-1.0