Projectiondesign F32 sx+ (North America) commands

Summary

DLP projector controllable over RS-232 and LAN (TCP/UDP port 1025) using an ASCII-framed protocol (: header, 4-byte mnemonic, optional modifier/value, CR terminator). This spec covers transport setup, the command frame format, and all documented ASCII commands. A browser-based configuration web page (default login admin/admin) is used for IP setup.

Transport

protocols:
  - serial
  - tcp
  - udp  # inferred: source labels the control port "TCP/UDP port" 1025; UDP usage not further described
serial:
  baud_rate: 19200  # default; configurable 4800/9600/19200 from projector menu
  data_bits: 8
  parity: none
  stop_bits: 1
  flow_control: none
addressing:
  port: 1025  # default TCP/UDP port; DHCP on by default
auth:
  type: none  # inferred: no login procedure described for the ASCII control protocol; source hints at access levels (ACSS command, error !00001). Web config page login: admin/admin - see Notes

Traits

# - powerable: POWR power on/off command present
# - queryable: '?' modifier and Get-only commands (POST, ISTS, THRM, ...) present
# - levelable: BRIG, CNTR, SHRP, VKEY, etc. with relative modifier R
# - routable: source-select commands (IVGA, IDVI, IHDM, ...)
traits:
  - powerable
  - queryable
  - levelable
  - routable

Actions

# Frame format (all commands): ':' HEADER + optional 1-3 byte ADDRESS + 4-byte MNEMONIC
# + optional MODIFIER/VALUE/TARGET + CR (0x0D). Single optional SPACE between fields.
# Mnemonics are not case sensitive. Values max 6 bytes, targets max 4 bytes.
#
# Modifiers: R = relative change (e.g. :BRIG R10 = +10 steps); A = request acknowledge;
# ? = get current value; ?M = max; ?N = min; ?D = default; ?S = default step.
# All commands listed as "Get, Set" support the query forms via these modifiers.
# Acknowledge is ON by default; toggle with ECHO. {value} placeholders: the source
# documents value semantics only where noted; otherwise value semantics are
# UNRESOLVED (not stated in source).
#
# NOTE: source command table lists several mnemonics twice with conflicting
# descriptions (SABS, S1T1, S169, SS43, SFLA, SFAR, SLET, SLST, SANL and
# LDMM, LPW1, DBDI, LDCR, LDCG, LDCB) - deduplicated here, first occurrence kept.

# ---- Power ----
- id: powr
  label: "Power"
  kind: action
  command: ":POWR{value}"
  notes: "Ops: Get, Set. 0 - power off, 1 - power on"
- id: post
  label: "Power State"
  kind: query
  command: ":POST?"
  notes: "Ops: Get. See value table POST (table not in source)"

# ---- Source selection ----
- id: iabs
  label: "Set Source Abs Values"
  kind: action
  command: ":IABS{value}"
  notes: "Ops: Get, Set. See value table IABS (table not in source)"
- id: ivga
  label: "Select VGA"
  kind: action
  command: ":IVGA{value}"
  notes: "Ops: Get, Set"
- id: isvi
  label: "Select S-Video"
  kind: action
  command: ":ISVI{value}"
  notes: "Ops: Get, Set"
- id: idvi
  label: "Select DVI"
  kind: action
  command: ":IDVI{value}"
  notes: "Ops: Get, Set"
- id: icvi
  label: "Select Composite Video"
  kind: action
  command: ":ICVI{value}"
  notes: "Ops: Get, Set"
- id: iypp
  label: "Select Component YPbPr"
  kind: action
  command: ":IYPP{value}"
  notes: "Ops: Get, Set"
- id: irgs
  label: "Select RGB Video"
  kind: action
  command: ":IRGS{value}"
  notes: "Ops: Get, Set"
- id: ihdm
  label: "Select HDMI"
  kind: action
  command: ":IHDM{value}"
  notes: "Ops: Get, Set"
- id: ibnc
  label: "Select BNC"
  kind: action
  command: ":IBNC{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: ixp2
  label: "Select Source XP2"
  kind: query
  command: ":IXP2?"
  notes: "Ops: Get. Platforms: GP3, GP4"
- id: ists
  label: "Signal Status"
  kind: query
  command: ":ISTS?"
  notes: "Ops: Get. 0 - searching, 1 - locked to source"

# ---- Picture ----
- id: brig
  label: "Brightness"
  kind: action
  command: ":BRIG{value}"
  notes: "Ops: Get, Set. Relative modifier supported (source example :BRIG R10)"
- id: cntr
  label: "Contrast"
  kind: action
  command: ":CNTR{value}"
  notes: "Ops: Get, Set. Source examples: :CNTR R1 increment, :CNTR R-2 decrement 2 steps"
- id: csat
  label: "Color"
  kind: action
  command: ":CSAT{value}"
  notes: "Ops: Get, Set"
- id: vhue
  label: "Hue Video"
  kind: action
  command: ":VHUE{value}"
  notes: "Ops: Get, Set"
- id: shrp
  label: "Sharpness"
  kind: action
  command: ":SHRP{value}"
  notes: "Ops: Get, Set"
- id: prst
  label: "Picture Reset"
  kind: action
  command: ":PRST{value}"
  notes: "Ops: Get, Set"
- id: auto
  label: "Auto"
  kind: action
  command: ":AUTO"
  notes: "Ops: Set"
- id: pmut
  label: "Picture Mute"
  kind: action
  command: ":PMUT{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: frze
  label: "Freeze Image"
  kind: action
  command: ":FRZE{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: sabs
  label: "Set Scaling Abs Value"
  kind: action
  command: ":SABS{value}"
  notes: "Ops: Get, Set. See value table SABS (table not in source). Duplicate source row also labels SABS 'Select Gamma Film' - probable table corruption"
- id: s1t1
  label: "Select Scaling 1:1"
  kind: action
  command: ":S1T1{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels S1T1 'Select Gamma Video'"
- id: s169
  label: "Select Scaling 16:9"
  kind: action
  command: ":S169{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels S169 'Select Gamma Computer'"
- id: ss43
  label: "Select Scaling 4:3"
  kind: action
  command: ":SS43{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SS43 'Set Gamma abs value' (see value table GABS)"
- id: sfla
  label: "Select Scaling FillAll"
  kind: action
  command: ":SFLA{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SFLA 'BrilliantColor Control'"
- id: sfar
  label: "Select Scaling FillAspectRatio"
  kind: action
  command: ":SFAR{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SFAR 'BrilliantColor Control'"
- id: slet
  label: "Select Scaling Letterbox to 16:9"
  kind: action
  command: ":SLET{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SLET 'BrilliantColor Control'"
- id: slst
  label: "Select Scaling Letterbox St to 16:9"
  kind: action
  command: ":SLST{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SLST 'BrilliantColor Mode'"
- id: sanl
  label: "Scale Anamorphic"
  kind: action
  command: ":SANL{value}"
  notes: "Ops: Get, Set. Platforms: GP1 1080, GP2 1080, GP3 1080, GP4 1080. 1 - flm 1, 2 - flm 2. Duplicate source row also labels SANL 'BrilliantColor Look'"
- id: gafi
  label: "Select Gamma Film"
  kind: action
  command: ":GAFI{value}"
  notes: "Ops: Get, Set. 1 - Film 1, 2 - Film 2"
- id: gavi
  label: "Select Gamma Video"
  kind: action
  command: ":GAVI{value}"
  notes: "Ops: Get, Set. 1 - Video 1, 2 - Video 2"
- id: gaco
  label: "Select Gamma Computer"
  kind: action
  command: ":GACO{value}"
  notes: "Ops: Get, Set. 1 - Computer 1, 2 - Computer 2"
- id: gabs
  label: "Set Gamma Abs Value"
  kind: action
  command: ":GABS{value}"
  notes: "Ops: Get, Set. See value table GABS (table not in source)"
- id: bccr
  label: "BrilliantColor Control"
  kind: action
  command: ":BCCR{value}"
  notes: "Ops: Get, Set. See value table BCCR (table not in source). Platforms: GP1, GP2, GP3"
- id: bcmo
  label: "BrilliantColor Mode"
  kind: action
  command: ":BCMO{value}"
  notes: "Ops: Get, Set. See value table BCMO (table not in source). Platforms: GP1, GP2, GP3"
- id: bcpr
  label: "BrilliantColor Look"
  kind: action
  command: ":BCPR{value}"
  notes: "Ops: Get, Set. See value table BCPR (table not in source). Platforms: GP1, GP2, GP3"
- id: pres
  label: "BrilliantColor Preset Settings"
  kind: action
  command: ":PRES{value}"
  notes: "Ops: Get, Set. See value table PRES (table not in source). Platforms: GP1"
- id: wpek
  label: "BrilliantColor Boost"
  kind: action
  command: ":WPEK{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3"
- id: cmxv
  label: "Color Management X-Coordinate"
  kind: action
  command: ":CMXV{value}"
  notes: "Ops: Get, Set"
- id: cmyv
  label: "Color Management Y-Coordinate"
  kind: action
  command: ":CMYV{value}"
  notes: "Ops: Get, Set"
- id: cmtv
  label: "Color Management Temperature"
  kind: action
  command: ":CMTV{value}"
  notes: "Ops: Get, Set. Range 3200 - 9300"
- id: cmna
  label: "Color Management Mode Not Corrected"
  kind: action
  command: ":CMNA{value}"
  notes: "Ops: Get, Set"
- id: cmte
  label: "Color Management Mode Color Temperature"
  kind: action
  command: ":CMTE{value}"
  notes: "Ops: Get, Set"
- id: ccxy
  label: "Color Management Mode Custom Coordinates"
  kind: action
  command: ":CCXY{value}"
  notes: "Ops: Get, Set"
- id: cmhs
  label: "Color Management Mode HSG"
  kind: action
  command: ":CMHS{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmpr
  label: "Color Management Mode Presets"
  kind: action
  command: ":CMPR{value}"
  notes: "Ops: not stated in source. Platforms: GP1"
- id: rd65
  label: "Reset to D65"
  kind: action
  command: ":RD65"
  notes: "Ops: Set"
- id: dscr
  label: "Desired Coords Mode"
  kind: action
  command: ":DSCR{value}"
  notes: "Ops: Get, Set. See value table DSCR (table not in source)"
- id: baga
  label: "Balance Gains Enable"
  kind: action
  command: ":BAGA{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP1, GP2, GP3"
- id: dsrx
  label: "Desired Red X"
  kind: action
  command: ":DSRX{value}"
  notes: "Ops: Get, Set"
- id: dsry
  label: "Desired Red Y"
  kind: action
  command: ":DSRY{value}"
  notes: "Ops: Get, Set"
- id: dsrg
  label: "Desired Red Gain"
  kind: action
  command: ":DSRG{value}"
  notes: "Ops: Get, Set"
- id: dsgx
  label: "Desired Green X"
  kind: action
  command: ":DSGX{value}"
  notes: "Ops: Get, Set"
- id: dsgy
  label: "Desired Green Y"
  kind: action
  command: ":DSGY{value}"
  notes: "Ops: Get, Set"
- id: dsgg
  label: "Desired Green Gain"
  kind: action
  command: ":DSGG{value}"
  notes: "Ops: Get, Set"
- id: dsbx
  label: "Desired Blue X"
  kind: action
  command: ":DSBX{value}"
  notes: "Ops: Get, Set"
- id: dsby
  label: "Desired Blue Y"
  kind: action
  command: ":DSBY{value}"
  notes: "Ops: Get, Set"
- id: dsbg
  label: "Desired Blue Gain"
  kind: action
  command: ":DSBG{value}"
  notes: "Ops: Get, Set"
- id: dscx
  label: "Desired Cyan X"
  kind: action
  command: ":DSCX{value}"
  notes: "Ops: Get, Set"
- id: dscy
  label: "Desired Cyan Y"
  kind: action
  command: ":DSCY{value}"
  notes: "Ops: Get, Set"
- id: dscg
  label: "Desired Cyan Gain"
  kind: action
  command: ":DSCG{value}"
  notes: "Ops: Get, Set"
- id: dsmx
  label: "Desired Magenta X"
  kind: action
  command: ":DSMX{value}"
  notes: "Ops: Get, Set"
- id: dsmy
  label: "Desired Magenta Y"
  kind: action
  command: ":DSMY{value}"
  notes: "Ops: Get, Set"
- id: dsmg
  label: "Desired Magenta Gain"
  kind: action
  command: ":DSMG{value}"
  notes: "Ops: Get, Set"
- id: dsyx
  label: "Desired Yellow X"
  kind: action
  command: ":DSYX{value}"
  notes: "Ops: Get, Set"
- id: dsyy
  label: "Desired Yellow Y"
  kind: action
  command: ":DSYY{value}"
  notes: "Ops: Get, Set"
- id: dsyg
  label: "Desired Yellow Gain"
  kind: action
  command: ":DSYG{value}"
  notes: "Ops: Get, Set"
- id: dswg
  label: "Desired White Gain"
  kind: action
  command: ":DSWG{value}"
  notes: "Ops: Get, Set"
- id: msrx
  label: "Measured Red X"
  kind: action
  command: ":MSRX{value}"
  notes: "Ops: Get, Set"
- id: msry
  label: "Measured Red Y"
  kind: action
  command: ":MSRY{value}"
  notes: "Ops: Get, Set"
- id: msrl
  label: "Measured Red Luminance"
  kind: action
  command: ":MSRL{value}"
  notes: "Ops: Get, Set"
- id: msgx
  label: "Measured Green X"
  kind: action
  command: ":MSGX{value}"
  notes: "Ops: Get, Set"
- id: msgy
  label: "Measured Green Y"
  kind: action
  command: ":MSGY{value}"
  notes: "Ops: Get, Set"
- id: msgl
  label: "Measured Green Luminance"
  kind: action
  command: ":MSGL{value}"
  notes: "Ops: Get, Set"
- id: msbx
  label: "Measured Blue X"
  kind: action
  command: ":MSBX{value}"
  notes: "Ops: Get, Set"
- id: msby
  label: "Measured Blue Y"
  kind: action
  command: ":MSBY{value}"
  notes: "Ops: Get, Set"
- id: msbl
  label: "Measured Blue Luminance"
  kind: action
  command: ":MSBL{value}"
  notes: "Ops: Get, Set"
- id: mswx
  label: "Measure White X"
  kind: action
  command: ":MSWX{value}"
  notes: "Ops: Get, Set"
- id: mswy
  label: "Measure White Y"
  kind: action
  command: ":MSWY{value}"
  notes: "Ops: Get, Set"
- id: mswl
  label: "Measure White Luminance"
  kind: action
  command: ":MSWL{value}"
  notes: "Ops: Get, Set"
- id: cmhr
  label: "ColorManagement Hue Red"
  kind: action
  command: ":CMHR{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhg
  label: "ColorManagement Hue Green"
  kind: action
  command: ":CMHG{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhb
  label: "ColorManagement Hue Blue"
  kind: action
  command: ":CMHB{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhc
  label: "ColorManagement Hue Cyan"
  kind: action
  command: ":CMHC{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhm
  label: "ColorManagement Hue Magenta"
  kind: action
  command: ":CMHM{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhy
  label: "ColorManagement Hue Yellow"
  kind: action
  command: ":CMHY{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsr
  label: "ColorManagement Saturation Red"
  kind: action
  command: ":CMSR{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsg
  label: "ColorManagement Saturation Green"
  kind: action
  command: ":CMSG{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsb
  label: "ColorManagement Saturation Blue"
  kind: action
  command: ":CMSB{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsc
  label: "ColorManagement Saturation Cyan"
  kind: action
  command: ":CMSC{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsm
  label: "ColorManagement Saturation Magenta"
  kind: action
  command: ":CMSM{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsy
  label: "ColorManagement Saturation Yellow"
  kind: action
  command: ":CMSY{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgr
  label: "ColorManagement Gain Red"
  kind: action
  command: ":CMGR{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgg
  label: "ColorManagement Gain Green"
  kind: action
  command: ":CMGG{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgb
  label: "ColorManagement Gain Blue"
  kind: action
  command: ":CMGB{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgc
  label: "ColorManagement Gain Cyan"
  kind: action
  command: ":CMGC{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgm
  label: "ColorManagement Gain Magenta"
  kind: action
  command: ":CMGM{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgy
  label: "ColorManagement Gain Yellow"
  kind: action
  command: ":CMGY{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmwr
  label: "ColorManagement White Balance Red"
  kind: action
  command: ":CMWR{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmwg
  label: "ColorManagement White Balance Green"
  kind: action
  command: ":CMWG{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmwb
  label: "ColorManagement White Balance Blue"
  kind: action
  command: ":CMWB{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmtp
  label: "Color Management Test Patterns"
  kind: action
  command: ":CMTP{value}"
  notes: "Ops: Get, Set"
- id: cmtg
  label: "PW Test Patterns"
  kind: action
  command: ":CMTG{value}"
  notes: "Ops: Get, Set. See value table CMTG (table not in source)"

# ---- Picture->RealColor->Display Customization ----
- id: bred
  label: "Red Offset"
  kind: action
  command: ":BRED{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: bgre
  label: "Green Offset"
  kind: action
  command: ":BGRE{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: bblu
  label: "Blue Offset"
  kind: action
  command: ":BBLU{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: cred
  label: "Red Gain"
  kind: action
  command: ":CRED{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: cgre
  label: "Green Gain"
  kind: action
  command: ":CGRE{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: cblu
  label: "Blue Gain"
  kind: action
  command: ":CBLU{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"

# ---- Picture->Advanced ----
- id: vpos
  label: "Vertical Position"
  kind: action
  command: ":VPOS{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: hpos
  label: "Horizontal Position"
  kind: action
  command: ":HPOS{value}"
  notes: "Ops: Get, Set"
- id: phse
  label: "Phase"
  kind: action
  command: ":PHSE{value}"
  notes: "Ops: Get, Set"
- id: freq
  label: "Frequency"
  kind: action
  command: ":FREQ{value}"
  notes: "Ops: Get, Set"
- id: nire
  label: "IRE Setup"
  kind: action
  command: ":NIRE{value}"
  notes: "Ops: Get, Set"
- id: dlsp
  label: "Digital Level and Colorspace"
  kind: action
  command: ":DLSP{value}"
  notes: "Ops: Get, Set. 0 - manual, 1 - auto"
- id: dvst
  label: "Digital Level"
  kind: action
  command: ":DVST{value}"
  notes: "Ops: Get, Set. 0 - computer, 1 - video"
- id: dcsp
  label: "Digital Colorspace"
  kind: action
  command: ":DCSP{value}"
  notes: "Ops: Get, Set"

# ---- Picture->Enhancements ----
- id: dlti
  label: "DLTI Level"
  kind: action
  command: ":DLTI{value}"
  notes: "Ops: Get, Set"
- id: dcti
  label: "DCTI Level"
  kind: action
  command: ":DCTI{value}"
  notes: "Ops: Get, Set"
- id: cb3d
  label: "3D Comb Filter"
  kind: action
  command: ":CB3D{value}"
  notes: "Ops: Get, Set"
- id: pk2d
  label: "2D Peaking"
  kind: action
  command: ":PK2D{value}"
  notes: "Ops: Get, Set"
- id: anoi
  label: "Adaptive Noise Reduction"
  kind: action
  command: ":ANOI{value}"
  notes: "Ops: Get, Set"
- id: cehr
  label: "CEH Red"
  kind: action
  command: ":CEHR{value}"
  notes: "Ops: Get, Set"
- id: cehb
  label: "CEH Blue"
  kind: action
  command: ":CEHB{value}"
  notes: "Ops: Get, Set"
- id: cehg
  label: "CEH Green"
  kind: action
  command: ":CEHG{value}"
  notes: "Ops: Get, Set"
- id: cehy
  label: "CEH Yellow"
  kind: action
  command: ":CEHY{value}"
  notes: "Ops: Get, Set"
- id: cehf
  label: "CEH Fleshtone"
  kind: action
  command: ":CEHF{value}"
  notes: "Ops: Get, Set"
- id: dync
  label: "Dynamic Contrast Enable"
  kind: action
  command: ":DYNC{value}"
  notes: "Ops: Get, Set"
- id: dynl
  label: "Dynamic Contrast Level"
  kind: action
  command: ":DYNL{value}"
  notes: "Ops: Get, Set"
- id: hdbl
  label: "Horizontal Deblocking"
  kind: action
  command: ":HDBL{value}"
  notes: "Ops: Get, Set"

# ---- Picture->Dynamic Black ----
- id: dben
  label: "Dynamic Black"
  kind: action
  command: ":DBEN{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP4, GP3 LED"

# ---- Installation ----
- id: desk
  label: "Select Orientation Desktop Front"
  kind: action
  command: ":DESK{value}"
  notes: "Ops: Get, Set"
- id: ceil
  label: "Select Orientation Ceiling Front"
  kind: action
  command: ":CEIL{value}"
  notes: "Ops: Get, Set"
- id: rdes
  label: "Select Orientation Desktop Rear"
  kind: action
  command: ":RDES{value}"
  notes: "Ops: Get, Set"
- id: rcei
  label: "Select Orientation Ceiling Rear"
  kind: action
  command: ":RCEI{value}"
  notes: "Ops: Get, Set"
- id: orie
  label: "Select Orientation Abs Value"
  kind: action
  command: ":ORIE{value}"
  notes: "Ops: Get, Set. See value table ORIE (table not in source)"
- id: scan
  label: "Source Scan"
  kind: action
  command: ":SCAN{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: vrgb
  label: "RGB Video"
  kind: action
  command: ":VRGB{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: bncr
  label: "BNC Colorspace RGB"
  kind: action
  command: ":BNCR{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: bncc
  label: "BNC Colorspace YPbPr"
  kind: action
  command: ":BNCC{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: ir01
  label: "IR Enable 1"
  kind: action
  command: ":IR01{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: ir02
  label: "IR Enable 2"
  kind: action
  command: ":IR02{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: ir03
  label: "IR Enable 3"
  kind: action
  command: ":IR03{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP3"
- id: wide
  label: "Wide Setup"
  kind: action
  command: ":WIDE{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: svga
  label: "Sync Termination VGA"
  kind: action
  command: ":SVGA{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: svg2
  label: "Sync Termination VGA 2"
  kind: action
  command: ":SVG2{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP1"
- id: sdvi
  label: "Sync Termination DVI-A"
  kind: action
  command: ":SDVI{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP2"
- id: sbnc
  label: "Sync Termination BNC"
  kind: action
  command: ":SBNC{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP3, GP4"
- id: osdc
  label: "OSD Enable"
  kind: action
  command: ":OSDC{value}"
  notes: "Ops: Get, Set. See value table OSDC (table not in source). Protocol section: 0 = OSD off, 1 = OSD show only warnings"
- id: test
  label: "Test Image"
  kind: action
  command: ":TEST{value}"
  notes: "Ops: Get, Set. 0 - 7 different test patterns"
- id: vkey
  label: "Vertical Keystone"
  kind: action
  command: ":VKEY{value}"
  notes: "Ops: Get, Set"
- id: sncl
  label: "Sync Level"
  kind: action
  command: ":SNCL{value}"
  notes: "Ops: Get, Set. Inftec only"
- id: sncs
  label: "Sync Level RGB Video"
  kind: action
  command: ":SNCS{value}"
  notes: "Ops: Get, Set. Inftec only. Platforms: GP1, GP2, GP3, GP4"
- id: csfi
  label: "Enable Color Space Convert"
  kind: action
  command: ":CSFI{value}"
  notes: "Ops: Get, Set. Inftec only"
- id: opfi
  label: "Enable Optical Filter"
  kind: action
  command: ":OPFI{value}"
  notes: "Ops: Get, Set. Inftec only. Platforms: GP3, GP4"
- id: vfve
  label: "Video Filter VGA Enable"
  kind: action
  command: ":VFVE{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP3, GP4"
- id: vfbe
  label: "Video Filter BNC Enable"
  kind: action
  command: ":VFBE{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP3, GP4"
- id: opfa
  label: "Optical Filter All"
  kind: action
  command: ":OPFA{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP4"

# ---- Installation->lamp/LED ----
- id: ecom
  label: "Eco Mode"
  kind: action
  command: ":ECOM{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: lpw1
  label: "Lamp1 Power / LED Power"
  kind: action
  command: ":LPW1{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP4, GP1_AS3D, GP3 LED. Duplicate row in IR-control section labels LPW1 'LED Power'"
- id: lpw2
  label: "Lamp2 Power"
  kind: action
  command: ":LPW2{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: dbdi
  label: "LED Power"
  kind: action
  command: ":DBDI{value}"
  notes: "Ops: Get, Set. See value table LMOD (table not in source). Platforms: GP3 LED"
- id: lmod
  label: "Lamp Mode"
  kind: action
  command: ":LMOD{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: ldly
  label: "Lamp Auto Switch Delay"
  kind: action
  command: ":LDLY{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: dual
  label: "Lamp Mode Dual"
  kind: action
  command: ":DUAL{value}"
  notes: "Ops: Get, Set. Use LMOD, this is for legacy support. Platforms: GP3, GP4"
- id: sngl
  label: "Lamp Mode Single"
  kind: action
  command: ":SNGL{value}"
  notes: "Ops: Get, Set. Use LMOD, this is for legacy support. Platforms: GP3, GP4"
- id: laut
  label: "Lamp Mode Auto"
  kind: action
  command: ":LAUT{value}"
  notes: "Ops: Get, Set. Use LMOD, this is for legacy support. Platforms: GP3, GP4"
- id: lact
  label: "Select Lamp In Single Mode"
  kind: action
  command: ":LACT{value}"
  notes: "Ops: Get, Set. Use LMOD, this is for legacy support. Platforms: GP3, GP4"
- id: ldmm
  label: "LED Dim Mode"
  kind: action
  command: ":LDMM{value}"
  notes: "Ops: Get, Set. 0 - standard, 1 - custom. Platforms: GP3 LED"
- id: ldcr
  label: "Custom LED Dim Red"
  kind: action
  command: ":LDCR{value}"
  notes: "Ops: Get, Set. 0-20. Platforms: GP3 LED"
- id: ldcg
  label: "Custom LED Dim Green"
  kind: action
  command: ":LDCG{value}"
  notes: "Ops: Get, Set. 0-20. Platforms: GP3 LED"
- id: ldcb
  label: "Custom LED Dim Blue"
  kind: action
  command: ":LDCB{value}"
  notes: "Ops: Get, Set. 0-20. Platforms: GP3 LED"

# ---- Installation->trigger ----
- id: smod
  label: "Screen Trigger Mode"
  kind: action
  command: ":SMOD{value}"
  notes: "Ops: Get, Set. See value table SMOD (table not in source)"
- id: amod
  label: "Aspect Trigger Mode"
  kind: action
  command: ":AMOD{value}"
  notes: "Ops: Get, Set. See value table AMOD (table not in source). Platforms: GP1, GP3, GP4, GP1_AS3D"

# ---- Installation->EDID ----
- id: edir
  label: "EDID Resolution"
  kind: action
  command: ":EDIR{value}"
  notes: "Ops: Get, Set. See value table EDIR (table not in source). Platforms: GP1, GP2, GP3, GP4"
- id: edit
  label: "EDID Type"
  kind: action
  command: ":EDIT{value}"
  notes: "Ops: Get, Set. See value table EDIT (table not in source). Platforms: GP1, GP2, GP3, GP4"
- id: edmd
  label: "EDID Mailbox Data, Auto Increment"
  kind: action
  command: ":EDMD{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP4"
- id: edmr
  label: "EDID Mailbox Counter Reset"
  kind: action
  command: ":EDMR{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP4"

# ---- Settings ----
- id: fcre
  label: "Factory Reset"
  kind: action
  command: ":FCRE"
  notes: "Ops: Set"
- id: fcrl
  label: "Factory Reset Level"
  kind: action
  command: ":FCRL{value}"
  notes: "Ops: Get, Set"
- id: pinc
  label: "PIN Code"
  kind: action
  command: ":PINC{value}"
  notes: "Ops: Set. Must be run in standby"
- id: code
  label: "Service Code"
  kind: action
  command: ":CODE{value}"
  notes: "Ops: Set"
- id: rcid
  label: "RCID Internal"
  kind: action
  command: ":RCID{value}"
  notes: "Ops: Get, Set"
- id: dpms
  label: "DPMS"
  kind: action
  command: ":DPMS{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: dpmt
  label: "DPMS Timeout"
  kind: action
  command: ":DPMT{value}"
  notes: "Ops: Get, Set"
- id: keyb
  label: "Backlight Timeout"
  kind: action
  command: ":KEYB{value}"
  notes: "Ops: Get, Set"

# ---- Profiles ----
- id: umst
  label: "Store User Settings"
  kind: action
  command: ":UMST{value}"
  notes: "Ops: Get, Set. User Settings is replaced by Profile in some software versions"
- id: umrc
  label: "Recall User Settings"
  kind: action
  command: ":UMRC{value}"
  notes: "Ops: Get, Set. User Settings is replaced by Profile in some software versions"
- id: stmo
  label: "Store Motor Position"
  kind: action
  command: ":STMO{value}"
  notes: "Ops: Set. Platforms: GP4"
- id: rcmo
  label: "Recall Motor Position"
  kind: action
  command: ":RCMO{value}"
  notes: "Ops: Set. Platforms: GP4"
- id: prmo
  label: "Profile Mode"
  kind: action
  command: ":PRMO{value}"
  notes: "Ops: Get, Set. 0 - Auto, 1 - Custom, 2 - ISF"
- id: pimo
  label: "Profile ISF Mode"
  kind: action
  command: ":PIMO{value}"
  notes: "Ops: Get, Set. 0 - ISF Day, 1 - ISF Night"
- id: pcen
  label: "Profile Custom Enable"
  kind: action
  command: ":PCEN {value} {target}"
  params:
    - name: value
      type: integer
      description: "0 - disable, 1 - enable"
    - name: target
      type: integer
      description: "Custom profile number (0 - 9)"
  notes: "Ops: Get, Set. Source example: ':PCEN 1 2' enables custom profile number 2"
- id: pcna
  label: "Profile Custom Name"
  kind: action
  command: ":PCNA {value} {target}"
  params:
    - name: value
      type: string
      description: "Profile name as string"
    - name: target
      type: integer
      description: "Custom profile number (0 - 9)"
  notes: "Ops: Get, Set"
- id: pcco
  label: "Profile Custom Connector"
  kind: query
  command: ":PCCO ? {target}"
  params:
    - name: target
      type: integer
      description: "Custom profile number (0 - 9)"
  notes: "Ops: Get. Value: Connector (see Profile Con List, not in source). Source example: ':PCCO ? 2' -> '%001 PCCO 000003'"
- id: prcc
  label: "Profile Custom Current Profile"
  kind: query
  command: ":PRCC?"
  notes: "Ops: Get"
- id: psto
  label: "Profile Custom Store"
  kind: action
  command: ":PSTO{value}"
  notes: "Ops: Set. See value table PSTO (table not in source)"
- id: pcrc
  label: "Profile Custom Recall"
  kind: action
  command: ":PCRC{value}"
  notes: "Ops: Set"
- id: prrc
  label: "Profile Custom Recall Current"
  kind: action
  command: ":PRRC{value}"
  notes: "Ops: Set"
- id: prer
  label: "Profile Custom Erase"
  kind: action
  command: ":PRER{value}"
  notes: "Ops: Set. See value table PRER (table not in source)"
- id: prch
  label: "Current Profile Changed?"
  kind: query
  command: ":PRCH?"
  notes: "Ops: Get. Returns string * (asterisk) if changed"

# ---- Lens control ----
- id: foin
  label: "Focus In"
  kind: action
  command: ":FOIN{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: fout
  label: "Focus Out"
  kind: action
  command: ":FOUT{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: zoin
  label: "Zoom In"
  kind: action
  command: ":ZOIN{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: zout
  label: "Zoom Out"
  kind: action
  command: ":ZOUT{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: irop
  label: "Iris Open"
  kind: action
  command: ":IROP{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: ircl
  label: "Iris Close"
  kind: action
  command: ":IRCL{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: lsdw
  label: "Lens Shift Down"
  kind: action
  command: ":LSDW{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: lsup
  label: "Lens Shift Up"
  kind: action
  command: ":LSUP{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: lslf
  label: "Lens Shift Left"
  kind: action
  command: ":LSLF{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: lsrh
  label: "Lens Shift Right"
  kind: action
  command: ":LSRH{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: shut
  label: "Shutter"
  kind: action
  command: ":SHUT{value}"
  notes: "Ops: Set. Platforms: GP3, GP4"

# ---- Menu navigate ----
- id: menu
  label: "Menu Navigate Toggle OSD Menu"
  kind: action
  command: ":MENU"
  notes: "Ops: Set"
- id: nvup
  label: "Menu Navigate Up"
  kind: action
  command: ":NVUP"
  notes: "Ops: Set"
- id: nvdw
  label: "Menu Navigate Down"
  kind: action
  command: ":NVDW"
  notes: "Ops: Set"
- id: nvlf
  label: "Menu Navigate Left"
  kind: action
  command: ":NVLF"
  notes: "Ops: Set"
- id: nvrh
  label: "Menu Navigate Right"
  kind: action
  command: ":NVRH"
  notes: "Ops: Set"
- id: nvok
  label: "Menu Navigate Ok"
  kind: action
  command: ":NVOK"
  notes: "Ops: Set"

# ---- Miscellaneous ----
- id: echo
  label: "Communication Response (On/Off)"
  kind: action
  command: ":ECHO{value}"
  notes: "Ops: Set. Toggles auto-acknowledge on/off; value semantics not stated in source"
- id: lang
  label: "Language"
  kind: action
  command: ":LANG{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP4"
- id: osdp
  label: "OSD Menu Position"
  kind: action
  command: ":OSDP{value}"
  notes: "Ops: Get, Set. 0 - standard, 1 - anamorph. Platforms: GP1 Avielo, GP2 Avielo, GP3 Avielo, GP4 Avielo"
- id: snam
  label: "Show OSD Projector ID"
  kind: action
  command: ":SNAM{value}"
  notes: "Ops: Set. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"
- id: sinf
  label: "Show OSD Info"
  kind: action
  command: ":SINF{value}"
  notes: "Ops: Set. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"
- id: mess
  label: "Show OSD Message"
  kind: action
  command: ":MESS{value}"
  notes: "Ops: Get, Set. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"
- id: name
  label: "Projector ID"
  kind: action
  command: ":NAME{value}"
  notes: "Ops: Get, Set. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"

# ---- Medical (GP2 medical only) ----
- id: mdof
  label: "Medical Off"
  kind: action
  command: ":MDOF{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdcl
  label: "Medical Clearbase"
  kind: action
  command: ":MDCL{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdbl
  label: "Medical Bluebase"
  kind: action
  command: ":MDBL{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdfw
  label: "Medical Full White"
  kind: action
  command: ":MDFW{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdcx
  label: "DICOM Clearbase X"
  kind: action
  command: ":MDCX{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdcy
  label: "DICOM Clearbase Y"
  kind: action
  command: ":MDCY{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdbx
  label: "DICOM Bluebase X"
  kind: action
  command: ":MDBX{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdby
  label: "DICOM Bluebase Y"
  kind: action
  command: ":MDBY{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"

# ---- Thermal ----
- id: thrm
  label: "Thermal Status"
  kind: query
  command: ":THRM?"
  notes: "Ops: Get"
- id: fan1
  label: "Fan Speed 1"
  kind: query
  command: ":FAN1?"
  notes: "Ops: Get"
- id: fan2
  label: "Fan Speed 2"
  kind: query
  command: ":FAN2?"
  notes: "Ops: Get"
- id: fan3
  label: "Fan Speed 3"
  kind: query
  command: ":FAN3?"
  notes: "Ops: Get"
- id: fan4
  label: "Fan Speed 4"
  kind: query
  command: ":FAN4?"
  notes: "Ops: Get"
- id: fan5
  label: "Fan Speed 5"
  kind: query
  command: ":FAN5?"
  notes: "Ops: Get"
- id: fan6
  label: "Fan Speed 6"
  kind: query
  command: ":FAN6?"
  notes: "Ops: Get"
- id: fan7
  label: "Fan Speed 7"
  kind: query
  command: ":FAN7?"
  notes: "Ops: Get"
- id: fan8
  label: "Fan Speed 8"
  kind: query
  command: ":FAN8?"
  notes: "Ops: Get"
- id: sns1
  label: "Sensor Value 1"
  kind: query
  command: ":SNS1?"
  notes: "Ops: Get"
- id: sns2
  label: "Sensor Value 2"
  kind: query
  command: ":SNS2?"
  notes: "Ops: Get"
- id: sns3
  label: "Sensor Value 3"
  kind: query
  command: ":SNS3?"
  notes: "Ops: Get"
- id: sns4
  label: "Sensor Value 4"
  kind: query
  command: ":SNS4?"
  notes: "Ops: Get"
- id: sns5
  label: "Sensor Value 5"
  kind: query
  command: ":SNS5?"
  notes: "Ops: Get"
- id: sns6
  label: "Sensor Value 6"
  kind: query
  command: ":SNS6?"
  notes: "Ops: Get"
- id: sns7
  label: "Sensor Value 7"
  kind: query
  command: ":SNS7?"
  notes: "Ops: Get"
- id: sns8
  label: "Sensor Value 8"
  kind: query
  command: ":SNS8?"
  notes: "Ops: Get"

# ---- Status ----
- id: plat
  label: "Platform Name String"
  kind: query
  command: ":PLAT?"
  notes: "Ops: Get. Extended Protocol"
- id: seri
  label: "Serial Number String"
  kind: query
  command: ":SERI?"
  notes: "Ops: Get. Extended Protocol. Source example: ':seri ?' -> '%001 SERI e00001 07010001'"
- id: modl
  label: "Model Name String"
  kind: query
  command: ":MODL?"
  notes: "Ops: Get. Extended Protocol"
- id: part
  label: "Part Number String"
  kind: query
  command: ":PART?"
  notes: "Ops: Get. Extended Protocol"
- id: sver
  label: "Software Version"
  kind: query
  command: ":SVER?"
  notes: "Ops: Get. Extended Protocol"
- id: swvr
  label: "Software Version"
  kind: query
  command: ":SWVR?"
  notes: "Ops: Get"
- id: acss
  label: "Current Access Level"
  kind: query
  command: ":ACSS?"
  notes: "Ops: Get"
- id: lest
  label: "Status LED State"
  kind: query
  command: ":LEST?"
  notes: "Ops: Get. See value table LEST (table not in source)"
- id: swsn
  label: "SVN SW Revision"
  kind: query
  command: ":SWSN?"
  notes: "Ops: Get. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"

# ---- ZoneCorrection ----
- id: zcen
  label: "ZoneCorrection Enable"
  kind: action
  command: ":ZCEN{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP4"

# ---- 3D stereo ----
- id: tdfs
  label: "3D Flash Slave"
  kind: action
  command: ":TDFS{value}"
  notes: "Ops: Set. Platforms: GP1_AS3D"
- id: tdgt
  label: "Glass Type"
  kind: action
  command: ":TDGT{value}"
  notes: "Ops: Get, Set. Platforms: GP1_AS3D"
- id: tdgd
  label: "Genlock Phase Delay"
  kind: action
  command: ":TDGD{value}"
  notes: "Ops: Get, Set. Platforms: GP1_AS3D"
- id: tdsm
  label: "Stereo Mode"
  kind: action
  command: ":TDSM{value}"
  notes: "Ops: Get, Set. Platforms: GP1_AS3D"
- id: tdsc
  label: "Connector Select Slave"
  kind: action
  command: ":TDSC{value}"
  notes: "Ops: Get, Set. Platforms: GP1_AS3D"

# ---- IR control ----
- id: auxl
  label: "IR LED Enable"
  kind: action
  command: ":AUXL{value}"
  notes: "Ops: Get, Set. Platforms: GP3_LED_IR"
- id: auxd
  label: "IR LED Dim"
  kind: action
  command: ":AUXD{value}"
  notes: "Ops: Get, Set. Platforms: GP3_LED_IR"
- id: disl
  label: "Turn Off RGB LEDs"
  kind: action
  command: ":DISL{value}"
  notes: "Ops: Get, Set. Platforms: GP3_LED_IR"

Feedbacks

# Acknowledge format: '%' + ADDRESS (3 bytes) + SPACE + COMMAND (4 bytes) + SPACE + VALUE (6 bytes) + CR (0x0D)
# Example: ":POWR1" -> "%001 POWR 000001"
- id: acknowledge
  type: string
  description: "Acknowledge response: %<addr> <MNEM> <6-byte value> CR. Acknowledge ON by default, toggled by ECHO or per-command modifier A"

# Error responses (returned in place of value when command invalid):
- id: error_access_denied
  type: enum
  values: ["!00001"]
  description: "Access denied - current access level is too low"
- id: error_not_available
  type: enum
  values: ["!00002"]
  description: "Not available - command currently not available (e.g. contrast not available when projector is searching)"
- id: error_not_implemented
  type: enum
  values: ["!00003"]
  description: "Not implemented"
- id: error_value_out_of_range
  type: enum
  values: ["!00004"]
  description: "Value out of range"
- id: extended_info_string
  type: string
  description: "'e00001' - extended info, a description string follows (for values longer than 6 characters)"

# Observable state via queries:
- id: power_state
  type: enum  # UNRESOLVED: POST value table not in source
  description: "Power state via POST query"
- id: signal_status
  type: enum
  values: [searching, locked]
  description: "Signal status via ISTS query: 0 - searching, 1 - locked to source"
- id: thermal_status
  type: string  # UNRESOLVED: value semantics not stated in source
  description: "Thermal status via THRM query"
- id: status_led_state
  type: enum  # UNRESOLVED: LEST value table not in source
  description: "Status LED state via LEST query"
- id: profile_changed
  type: enum
  values: ["*"]
  description: "PRCH query returns * (asterisk) if current profile changed"

Variables

# All settable parameters are modeled as Actions in this spec (one action per source
# command row); no additional variables documented in source.
# UNRESOLVED: value ranges for most level-type commands (BRIG, CNTR, CSAT, VHUE, SHRP,
# VKEY, ...) not stated in source; runtime discovery possible via ?M/?N/?D/?S modifiers.

Events

# UNRESOLVED: no unsolicited notifications documented in source. Some commands generate
# OSD feedback (suppressible via OSDC 0/1), but no push events described.

Macros

# UNRESOLVED: no multi-step sequences described explicitly in source.

Safety

confirmation_required_for: []
interlocks:
  - "Wait 30 seconds after power on before sending next command (explicit source requirement)"
  - "PINC (PIN Code) must be run in standby (explicit source requirement)"
# UNRESOLVED: no other safety warnings or interlock procedures in source.

Notes

Protocol frame: : header (required) + optional address (1-3 bytes) + message body + CR (0x0D) terminator (required). Optional single SPACE between fields; with or without space accepted. Mnemonics not case sensitive.
Timing constraints (source): wait for response before sending next command; minimum 2 s delay before resending if no response; minimum 500 ms between commands; minimum 5 s delay after sending 20 commands.
RS-232 wiring: standard serial cable, 9-pin female to host, 9-pin male to projector; pin 2-2, pin 3-3, pin 5-5.
LAN defaults: DHCP On, IP/subnet/gateway 0.0.0.0 (until assigned), TCP/UDP port 1025, web login username admin password admin (both case sensitive). Web page (browser-based) configures IP settings, port, password, and shows network firmware version; it is not documented as a REST/HTTP control API.
Acknowledges ON by default; ECHO toggles them; modifier A requests acknowledge per command.
Extended Protocol commands (SNAM, SINF, MESS, NAME, PLAT, SERI, MODL, PART, SVER, SWSN) marked as such in source; distinction from base protocol not explained.
Platform note: source maps GP1=F10 series, GP2=F20/evo 20/cineo 20, GP3=F30/cineo 30; GP4 products not enumerated. F32 is not listed, so which commands apply to F32 sx+ is unresolved; all documented commands included for coverage.
Source command table contains duplicate mnemonic rows with conflicting descriptions (SABS, S1T1, S169, SS43, SFLA, SFAR, SLET, SLST, SANL; and LDMM, LPW1, DBDI, LDCR, LDCG, LDCB in the IR-control section) — probable PDF-extraction corruption; deduplicated with both meanings noted.
Referenced value tables (POST, IABS, SABS, GABS, BCCR, BCMO, BCPR, PRES, DSCR, CMTG, ORIE, OSDC, SMOD, AMOD, EDIR, EDIT, PSTO, PRER, LEST, LMOD) are not included in the source document.

Provenance

source_domains:
  - web.archive.org
  - manualslib.com
  - applicationmarket.crestron.com
source_urls:
  - "https://web.archive.org/web/20131222040438/http://www.projectiondesign.com/products/f32-series/_attachment/1663?_ts=13e30ff66f4&download=true"
  - "https://www.manualslib.com/manual/2456229/Projectiondesign-F32-SxPlus.html?page=46"
  - https://applicationmarket.crestron.com/content/Help/ProjectionDesign/projectiondesign_f32_sx_serial_v1_0_help.pdf
  - "https://www.manualslib.com/manual/1133778/Projectiondesign-F32.html?page=46"
retrieved_at: 2026-08-18T12:44:23.806Z
last_checked_at: 2026-08-19T09:40:26.970Z

Verification Summary

verdict: verified
checked_at: 2026-08-19T09:40:26.970Z
matched_actions: 270
action_count: 270
confidence: medium
summary: "All 270 spec mnemonics appear verbatim in the source ASCII command table; transport values (port 1025, baud 19200, 8N1, no flow control) all supported. (12 unresolved item(s) noted in Known Gaps.)"

Known Gaps

- "F32 sx+ platform generation (GP1/GP2/GP3/GP4) not stated in source — per-command applicability to F32 sx+ is unresolved. Referenced value tables (POST, IABS, SABS, GABS, BCCR, BCMO, BCPR, PRES, DSCR, CMTG, ORIE, OSDC, SMOD, AMOD, EDIR, EDIT, PSTO, PRER, LEST, LMOD) are not included in the source."
- "POST value table not in source"
- "value semantics not stated in source"
- "LEST value table not in source"
- "value ranges for most level-type commands (BRIG, CNTR, CSAT, VHUE, SHRP,"
- "no unsolicited notifications documented in source. Some commands generate"
- "no multi-step sequences described explicitly in source."
- "no other safety warnings or interlock procedures in source."
- "firmware version compatibility not stated in source"
- "F32 sx+ platform generation (GP1-GP4) not stated; per-command applicability unknown"
- "value tables referenced but absent from source"
- "UDP control behavior only implied by \"TCP/UDP port\" label; LAN control framing identical to RS-232 assumed from \"connected to either RS232 or LAN ... through this ASCII based protocol\""

From the AI4AV catalog (https://ai4av.net) · ODbL-1.0

Summary

Transport

protocols:
  - serial
  - tcp
  - udp  # inferred: source labels the control port "TCP/UDP port" 1025; UDP usage not further described
serial:
  baud_rate: 19200  # default; configurable 4800/9600/19200 from projector menu
  data_bits: 8
  parity: none
  stop_bits: 1
  flow_control: none
addressing:
  port: 1025  # default TCP/UDP port; DHCP on by default
auth:
  type: none  # inferred: no login procedure described for the ASCII control protocol; source hints at access levels (ACSS command, error !00001). Web config page login: admin/admin - see Notes

Traits

# - powerable: POWR power on/off command present
# - queryable: '?' modifier and Get-only commands (POST, ISTS, THRM, ...) present
# - levelable: BRIG, CNTR, SHRP, VKEY, etc. with relative modifier R
# - routable: source-select commands (IVGA, IDVI, IHDM, ...)
traits:
  - powerable
  - queryable
  - levelable
  - routable

Actions

# Frame format (all commands): ':' HEADER + optional 1-3 byte ADDRESS + 4-byte MNEMONIC
# + optional MODIFIER/VALUE/TARGET + CR (0x0D). Single optional SPACE between fields.
# Mnemonics are not case sensitive. Values max 6 bytes, targets max 4 bytes.
#
# Modifiers: R = relative change (e.g. :BRIG R10 = +10 steps); A = request acknowledge;
# ? = get current value; ?M = max; ?N = min; ?D = default; ?S = default step.
# All commands listed as "Get, Set" support the query forms via these modifiers.
# Acknowledge is ON by default; toggle with ECHO. {value} placeholders: the source
# documents value semantics only where noted; otherwise value semantics are
# UNRESOLVED (not stated in source).
#
# NOTE: source command table lists several mnemonics twice with conflicting
# descriptions (SABS, S1T1, S169, SS43, SFLA, SFAR, SLET, SLST, SANL and
# LDMM, LPW1, DBDI, LDCR, LDCG, LDCB) - deduplicated here, first occurrence kept.

# ---- Power ----
- id: powr
  label: "Power"
  kind: action
  command: ":POWR{value}"
  notes: "Ops: Get, Set. 0 - power off, 1 - power on"
- id: post
  label: "Power State"
  kind: query
  command: ":POST?"
  notes: "Ops: Get. See value table POST (table not in source)"

# ---- Source selection ----
- id: iabs
  label: "Set Source Abs Values"
  kind: action
  command: ":IABS{value}"
  notes: "Ops: Get, Set. See value table IABS (table not in source)"
- id: ivga
  label: "Select VGA"
  kind: action
  command: ":IVGA{value}"
  notes: "Ops: Get, Set"
- id: isvi
  label: "Select S-Video"
  kind: action
  command: ":ISVI{value}"
  notes: "Ops: Get, Set"
- id: idvi
  label: "Select DVI"
  kind: action
  command: ":IDVI{value}"
  notes: "Ops: Get, Set"
- id: icvi
  label: "Select Composite Video"
  kind: action
  command: ":ICVI{value}"
  notes: "Ops: Get, Set"
- id: iypp
  label: "Select Component YPbPr"
  kind: action
  command: ":IYPP{value}"
  notes: "Ops: Get, Set"
- id: irgs
  label: "Select RGB Video"
  kind: action
  command: ":IRGS{value}"
  notes: "Ops: Get, Set"
- id: ihdm
  label: "Select HDMI"
  kind: action
  command: ":IHDM{value}"
  notes: "Ops: Get, Set"
- id: ibnc
  label: "Select BNC"
  kind: action
  command: ":IBNC{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: ixp2
  label: "Select Source XP2"
  kind: query
  command: ":IXP2?"
  notes: "Ops: Get. Platforms: GP3, GP4"
- id: ists
  label: "Signal Status"
  kind: query
  command: ":ISTS?"
  notes: "Ops: Get. 0 - searching, 1 - locked to source"

# ---- Picture ----
- id: brig
  label: "Brightness"
  kind: action
  command: ":BRIG{value}"
  notes: "Ops: Get, Set. Relative modifier supported (source example :BRIG R10)"
- id: cntr
  label: "Contrast"
  kind: action
  command: ":CNTR{value}"
  notes: "Ops: Get, Set. Source examples: :CNTR R1 increment, :CNTR R-2 decrement 2 steps"
- id: csat
  label: "Color"
  kind: action
  command: ":CSAT{value}"
  notes: "Ops: Get, Set"
- id: vhue
  label: "Hue Video"
  kind: action
  command: ":VHUE{value}"
  notes: "Ops: Get, Set"
- id: shrp
  label: "Sharpness"
  kind: action
  command: ":SHRP{value}"
  notes: "Ops: Get, Set"
- id: prst
  label: "Picture Reset"
  kind: action
  command: ":PRST{value}"
  notes: "Ops: Get, Set"
- id: auto
  label: "Auto"
  kind: action
  command: ":AUTO"
  notes: "Ops: Set"
- id: pmut
  label: "Picture Mute"
  kind: action
  command: ":PMUT{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: frze
  label: "Freeze Image"
  kind: action
  command: ":FRZE{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: sabs
  label: "Set Scaling Abs Value"
  kind: action
  command: ":SABS{value}"
  notes: "Ops: Get, Set. See value table SABS (table not in source). Duplicate source row also labels SABS 'Select Gamma Film' - probable table corruption"
- id: s1t1
  label: "Select Scaling 1:1"
  kind: action
  command: ":S1T1{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels S1T1 'Select Gamma Video'"
- id: s169
  label: "Select Scaling 16:9"
  kind: action
  command: ":S169{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels S169 'Select Gamma Computer'"
- id: ss43
  label: "Select Scaling 4:3"
  kind: action
  command: ":SS43{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SS43 'Set Gamma abs value' (see value table GABS)"
- id: sfla
  label: "Select Scaling FillAll"
  kind: action
  command: ":SFLA{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SFLA 'BrilliantColor Control'"
- id: sfar
  label: "Select Scaling FillAspectRatio"
  kind: action
  command: ":SFAR{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SFAR 'BrilliantColor Control'"
- id: slet
  label: "Select Scaling Letterbox to 16:9"
  kind: action
  command: ":SLET{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SLET 'BrilliantColor Control'"
- id: slst
  label: "Select Scaling Letterbox St to 16:9"
  kind: action
  command: ":SLST{value}"
  notes: "Ops: Get, Set. Duplicate source row also labels SLST 'BrilliantColor Mode'"
- id: sanl
  label: "Scale Anamorphic"
  kind: action
  command: ":SANL{value}"
  notes: "Ops: Get, Set. Platforms: GP1 1080, GP2 1080, GP3 1080, GP4 1080. 1 - flm 1, 2 - flm 2. Duplicate source row also labels SANL 'BrilliantColor Look'"
- id: gafi
  label: "Select Gamma Film"
  kind: action
  command: ":GAFI{value}"
  notes: "Ops: Get, Set. 1 - Film 1, 2 - Film 2"
- id: gavi
  label: "Select Gamma Video"
  kind: action
  command: ":GAVI{value}"
  notes: "Ops: Get, Set. 1 - Video 1, 2 - Video 2"
- id: gaco
  label: "Select Gamma Computer"
  kind: action
  command: ":GACO{value}"
  notes: "Ops: Get, Set. 1 - Computer 1, 2 - Computer 2"
- id: gabs
  label: "Set Gamma Abs Value"
  kind: action
  command: ":GABS{value}"
  notes: "Ops: Get, Set. See value table GABS (table not in source)"
- id: bccr
  label: "BrilliantColor Control"
  kind: action
  command: ":BCCR{value}"
  notes: "Ops: Get, Set. See value table BCCR (table not in source). Platforms: GP1, GP2, GP3"
- id: bcmo
  label: "BrilliantColor Mode"
  kind: action
  command: ":BCMO{value}"
  notes: "Ops: Get, Set. See value table BCMO (table not in source). Platforms: GP1, GP2, GP3"
- id: bcpr
  label: "BrilliantColor Look"
  kind: action
  command: ":BCPR{value}"
  notes: "Ops: Get, Set. See value table BCPR (table not in source). Platforms: GP1, GP2, GP3"
- id: pres
  label: "BrilliantColor Preset Settings"
  kind: action
  command: ":PRES{value}"
  notes: "Ops: Get, Set. See value table PRES (table not in source). Platforms: GP1"
- id: wpek
  label: "BrilliantColor Boost"
  kind: action
  command: ":WPEK{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3"
- id: cmxv
  label: "Color Management X-Coordinate"
  kind: action
  command: ":CMXV{value}"
  notes: "Ops: Get, Set"
- id: cmyv
  label: "Color Management Y-Coordinate"
  kind: action
  command: ":CMYV{value}"
  notes: "Ops: Get, Set"
- id: cmtv
  label: "Color Management Temperature"
  kind: action
  command: ":CMTV{value}"
  notes: "Ops: Get, Set. Range 3200 - 9300"
- id: cmna
  label: "Color Management Mode Not Corrected"
  kind: action
  command: ":CMNA{value}"
  notes: "Ops: Get, Set"
- id: cmte
  label: "Color Management Mode Color Temperature"
  kind: action
  command: ":CMTE{value}"
  notes: "Ops: Get, Set"
- id: ccxy
  label: "Color Management Mode Custom Coordinates"
  kind: action
  command: ":CCXY{value}"
  notes: "Ops: Get, Set"
- id: cmhs
  label: "Color Management Mode HSG"
  kind: action
  command: ":CMHS{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmpr
  label: "Color Management Mode Presets"
  kind: action
  command: ":CMPR{value}"
  notes: "Ops: not stated in source. Platforms: GP1"
- id: rd65
  label: "Reset to D65"
  kind: action
  command: ":RD65"
  notes: "Ops: Set"
- id: dscr
  label: "Desired Coords Mode"
  kind: action
  command: ":DSCR{value}"
  notes: "Ops: Get, Set. See value table DSCR (table not in source)"
- id: baga
  label: "Balance Gains Enable"
  kind: action
  command: ":BAGA{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP1, GP2, GP3"
- id: dsrx
  label: "Desired Red X"
  kind: action
  command: ":DSRX{value}"
  notes: "Ops: Get, Set"
- id: dsry
  label: "Desired Red Y"
  kind: action
  command: ":DSRY{value}"
  notes: "Ops: Get, Set"
- id: dsrg
  label: "Desired Red Gain"
  kind: action
  command: ":DSRG{value}"
  notes: "Ops: Get, Set"
- id: dsgx
  label: "Desired Green X"
  kind: action
  command: ":DSGX{value}"
  notes: "Ops: Get, Set"
- id: dsgy
  label: "Desired Green Y"
  kind: action
  command: ":DSGY{value}"
  notes: "Ops: Get, Set"
- id: dsgg
  label: "Desired Green Gain"
  kind: action
  command: ":DSGG{value}"
  notes: "Ops: Get, Set"
- id: dsbx
  label: "Desired Blue X"
  kind: action
  command: ":DSBX{value}"
  notes: "Ops: Get, Set"
- id: dsby
  label: "Desired Blue Y"
  kind: action
  command: ":DSBY{value}"
  notes: "Ops: Get, Set"
- id: dsbg
  label: "Desired Blue Gain"
  kind: action
  command: ":DSBG{value}"
  notes: "Ops: Get, Set"
- id: dscx
  label: "Desired Cyan X"
  kind: action
  command: ":DSCX{value}"
  notes: "Ops: Get, Set"
- id: dscy
  label: "Desired Cyan Y"
  kind: action
  command: ":DSCY{value}"
  notes: "Ops: Get, Set"
- id: dscg
  label: "Desired Cyan Gain"
  kind: action
  command: ":DSCG{value}"
  notes: "Ops: Get, Set"
- id: dsmx
  label: "Desired Magenta X"
  kind: action
  command: ":DSMX{value}"
  notes: "Ops: Get, Set"
- id: dsmy
  label: "Desired Magenta Y"
  kind: action
  command: ":DSMY{value}"
  notes: "Ops: Get, Set"
- id: dsmg
  label: "Desired Magenta Gain"
  kind: action
  command: ":DSMG{value}"
  notes: "Ops: Get, Set"
- id: dsyx
  label: "Desired Yellow X"
  kind: action
  command: ":DSYX{value}"
  notes: "Ops: Get, Set"
- id: dsyy
  label: "Desired Yellow Y"
  kind: action
  command: ":DSYY{value}"
  notes: "Ops: Get, Set"
- id: dsyg
  label: "Desired Yellow Gain"
  kind: action
  command: ":DSYG{value}"
  notes: "Ops: Get, Set"
- id: dswg
  label: "Desired White Gain"
  kind: action
  command: ":DSWG{value}"
  notes: "Ops: Get, Set"
- id: msrx
  label: "Measured Red X"
  kind: action
  command: ":MSRX{value}"
  notes: "Ops: Get, Set"
- id: msry
  label: "Measured Red Y"
  kind: action
  command: ":MSRY{value}"
  notes: "Ops: Get, Set"
- id: msrl
  label: "Measured Red Luminance"
  kind: action
  command: ":MSRL{value}"
  notes: "Ops: Get, Set"
- id: msgx
  label: "Measured Green X"
  kind: action
  command: ":MSGX{value}"
  notes: "Ops: Get, Set"
- id: msgy
  label: "Measured Green Y"
  kind: action
  command: ":MSGY{value}"
  notes: "Ops: Get, Set"
- id: msgl
  label: "Measured Green Luminance"
  kind: action
  command: ":MSGL{value}"
  notes: "Ops: Get, Set"
- id: msbx
  label: "Measured Blue X"
  kind: action
  command: ":MSBX{value}"
  notes: "Ops: Get, Set"
- id: msby
  label: "Measured Blue Y"
  kind: action
  command: ":MSBY{value}"
  notes: "Ops: Get, Set"
- id: msbl
  label: "Measured Blue Luminance"
  kind: action
  command: ":MSBL{value}"
  notes: "Ops: Get, Set"
- id: mswx
  label: "Measure White X"
  kind: action
  command: ":MSWX{value}"
  notes: "Ops: Get, Set"
- id: mswy
  label: "Measure White Y"
  kind: action
  command: ":MSWY{value}"
  notes: "Ops: Get, Set"
- id: mswl
  label: "Measure White Luminance"
  kind: action
  command: ":MSWL{value}"
  notes: "Ops: Get, Set"
- id: cmhr
  label: "ColorManagement Hue Red"
  kind: action
  command: ":CMHR{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhg
  label: "ColorManagement Hue Green"
  kind: action
  command: ":CMHG{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhb
  label: "ColorManagement Hue Blue"
  kind: action
  command: ":CMHB{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhc
  label: "ColorManagement Hue Cyan"
  kind: action
  command: ":CMHC{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhm
  label: "ColorManagement Hue Magenta"
  kind: action
  command: ":CMHM{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmhy
  label: "ColorManagement Hue Yellow"
  kind: action
  command: ":CMHY{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsr
  label: "ColorManagement Saturation Red"
  kind: action
  command: ":CMSR{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsg
  label: "ColorManagement Saturation Green"
  kind: action
  command: ":CMSG{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsb
  label: "ColorManagement Saturation Blue"
  kind: action
  command: ":CMSB{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsc
  label: "ColorManagement Saturation Cyan"
  kind: action
  command: ":CMSC{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsm
  label: "ColorManagement Saturation Magenta"
  kind: action
  command: ":CMSM{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmsy
  label: "ColorManagement Saturation Yellow"
  kind: action
  command: ":CMSY{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgr
  label: "ColorManagement Gain Red"
  kind: action
  command: ":CMGR{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgg
  label: "ColorManagement Gain Green"
  kind: action
  command: ":CMGG{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgb
  label: "ColorManagement Gain Blue"
  kind: action
  command: ":CMGB{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgc
  label: "ColorManagement Gain Cyan"
  kind: action
  command: ":CMGC{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgm
  label: "ColorManagement Gain Magenta"
  kind: action
  command: ":CMGM{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmgy
  label: "ColorManagement Gain Yellow"
  kind: action
  command: ":CMGY{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmwr
  label: "ColorManagement White Balance Red"
  kind: action
  command: ":CMWR{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmwg
  label: "ColorManagement White Balance Green"
  kind: action
  command: ":CMWG{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmwb
  label: "ColorManagement White Balance Blue"
  kind: action
  command: ":CMWB{value}"
  notes: "Ops: Get, Set. Platforms: GP1"
- id: cmtp
  label: "Color Management Test Patterns"
  kind: action
  command: ":CMTP{value}"
  notes: "Ops: Get, Set"
- id: cmtg
  label: "PW Test Patterns"
  kind: action
  command: ":CMTG{value}"
  notes: "Ops: Get, Set. See value table CMTG (table not in source)"

# ---- Picture->RealColor->Display Customization ----
- id: bred
  label: "Red Offset"
  kind: action
  command: ":BRED{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: bgre
  label: "Green Offset"
  kind: action
  command: ":BGRE{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: bblu
  label: "Blue Offset"
  kind: action
  command: ":BBLU{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: cred
  label: "Red Gain"
  kind: action
  command: ":CRED{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: cgre
  label: "Green Gain"
  kind: action
  command: ":CGRE{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: cblu
  label: "Blue Gain"
  kind: action
  command: ":CBLU{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"

# ---- Picture->Advanced ----
- id: vpos
  label: "Vertical Position"
  kind: action
  command: ":VPOS{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP1_AS3D"
- id: hpos
  label: "Horizontal Position"
  kind: action
  command: ":HPOS{value}"
  notes: "Ops: Get, Set"
- id: phse
  label: "Phase"
  kind: action
  command: ":PHSE{value}"
  notes: "Ops: Get, Set"
- id: freq
  label: "Frequency"
  kind: action
  command: ":FREQ{value}"
  notes: "Ops: Get, Set"
- id: nire
  label: "IRE Setup"
  kind: action
  command: ":NIRE{value}"
  notes: "Ops: Get, Set"
- id: dlsp
  label: "Digital Level and Colorspace"
  kind: action
  command: ":DLSP{value}"
  notes: "Ops: Get, Set. 0 - manual, 1 - auto"
- id: dvst
  label: "Digital Level"
  kind: action
  command: ":DVST{value}"
  notes: "Ops: Get, Set. 0 - computer, 1 - video"
- id: dcsp
  label: "Digital Colorspace"
  kind: action
  command: ":DCSP{value}"
  notes: "Ops: Get, Set"

# ---- Picture->Enhancements ----
- id: dlti
  label: "DLTI Level"
  kind: action
  command: ":DLTI{value}"
  notes: "Ops: Get, Set"
- id: dcti
  label: "DCTI Level"
  kind: action
  command: ":DCTI{value}"
  notes: "Ops: Get, Set"
- id: cb3d
  label: "3D Comb Filter"
  kind: action
  command: ":CB3D{value}"
  notes: "Ops: Get, Set"
- id: pk2d
  label: "2D Peaking"
  kind: action
  command: ":PK2D{value}"
  notes: "Ops: Get, Set"
- id: anoi
  label: "Adaptive Noise Reduction"
  kind: action
  command: ":ANOI{value}"
  notes: "Ops: Get, Set"
- id: cehr
  label: "CEH Red"
  kind: action
  command: ":CEHR{value}"
  notes: "Ops: Get, Set"
- id: cehb
  label: "CEH Blue"
  kind: action
  command: ":CEHB{value}"
  notes: "Ops: Get, Set"
- id: cehg
  label: "CEH Green"
  kind: action
  command: ":CEHG{value}"
  notes: "Ops: Get, Set"
- id: cehy
  label: "CEH Yellow"
  kind: action
  command: ":CEHY{value}"
  notes: "Ops: Get, Set"
- id: cehf
  label: "CEH Fleshtone"
  kind: action
  command: ":CEHF{value}"
  notes: "Ops: Get, Set"
- id: dync
  label: "Dynamic Contrast Enable"
  kind: action
  command: ":DYNC{value}"
  notes: "Ops: Get, Set"
- id: dynl
  label: "Dynamic Contrast Level"
  kind: action
  command: ":DYNL{value}"
  notes: "Ops: Get, Set"
- id: hdbl
  label: "Horizontal Deblocking"
  kind: action
  command: ":HDBL{value}"
  notes: "Ops: Get, Set"

# ---- Picture->Dynamic Black ----
- id: dben
  label: "Dynamic Black"
  kind: action
  command: ":DBEN{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP4, GP3 LED"

# ---- Installation ----
- id: desk
  label: "Select Orientation Desktop Front"
  kind: action
  command: ":DESK{value}"
  notes: "Ops: Get, Set"
- id: ceil
  label: "Select Orientation Ceiling Front"
  kind: action
  command: ":CEIL{value}"
  notes: "Ops: Get, Set"
- id: rdes
  label: "Select Orientation Desktop Rear"
  kind: action
  command: ":RDES{value}"
  notes: "Ops: Get, Set"
- id: rcei
  label: "Select Orientation Ceiling Rear"
  kind: action
  command: ":RCEI{value}"
  notes: "Ops: Get, Set"
- id: orie
  label: "Select Orientation Abs Value"
  kind: action
  command: ":ORIE{value}"
  notes: "Ops: Get, Set. See value table ORIE (table not in source)"
- id: scan
  label: "Source Scan"
  kind: action
  command: ":SCAN{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: vrgb
  label: "RGB Video"
  kind: action
  command: ":VRGB{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: bncr
  label: "BNC Colorspace RGB"
  kind: action
  command: ":BNCR{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: bncc
  label: "BNC Colorspace YPbPr"
  kind: action
  command: ":BNCC{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: ir01
  label: "IR Enable 1"
  kind: action
  command: ":IR01{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: ir02
  label: "IR Enable 2"
  kind: action
  command: ":IR02{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: ir03
  label: "IR Enable 3"
  kind: action
  command: ":IR03{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP3"
- id: wide
  label: "Wide Setup"
  kind: action
  command: ":WIDE{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: svga
  label: "Sync Termination VGA"
  kind: action
  command: ":SVGA{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: svg2
  label: "Sync Termination VGA 2"
  kind: action
  command: ":SVG2{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP1"
- id: sdvi
  label: "Sync Termination DVI-A"
  kind: action
  command: ":SDVI{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP2"
- id: sbnc
  label: "Sync Termination BNC"
  kind: action
  command: ":SBNC{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP3, GP4"
- id: osdc
  label: "OSD Enable"
  kind: action
  command: ":OSDC{value}"
  notes: "Ops: Get, Set. See value table OSDC (table not in source). Protocol section: 0 = OSD off, 1 = OSD show only warnings"
- id: test
  label: "Test Image"
  kind: action
  command: ":TEST{value}"
  notes: "Ops: Get, Set. 0 - 7 different test patterns"
- id: vkey
  label: "Vertical Keystone"
  kind: action
  command: ":VKEY{value}"
  notes: "Ops: Get, Set"
- id: sncl
  label: "Sync Level"
  kind: action
  command: ":SNCL{value}"
  notes: "Ops: Get, Set. Inftec only"
- id: sncs
  label: "Sync Level RGB Video"
  kind: action
  command: ":SNCS{value}"
  notes: "Ops: Get, Set. Inftec only. Platforms: GP1, GP2, GP3, GP4"
- id: csfi
  label: "Enable Color Space Convert"
  kind: action
  command: ":CSFI{value}"
  notes: "Ops: Get, Set. Inftec only"
- id: opfi
  label: "Enable Optical Filter"
  kind: action
  command: ":OPFI{value}"
  notes: "Ops: Get, Set. Inftec only. Platforms: GP3, GP4"
- id: vfve
  label: "Video Filter VGA Enable"
  kind: action
  command: ":VFVE{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP3, GP4"
- id: vfbe
  label: "Video Filter BNC Enable"
  kind: action
  command: ":VFBE{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP3, GP4"
- id: opfa
  label: "Optical Filter All"
  kind: action
  command: ":OPFA{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP4"

# ---- Installation->lamp/LED ----
- id: ecom
  label: "Eco Mode"
  kind: action
  command: ":ECOM{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: lpw1
  label: "Lamp1 Power / LED Power"
  kind: action
  command: ":LPW1{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP4, GP1_AS3D, GP3 LED. Duplicate row in IR-control section labels LPW1 'LED Power'"
- id: lpw2
  label: "Lamp2 Power"
  kind: action
  command: ":LPW2{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: dbdi
  label: "LED Power"
  kind: action
  command: ":DBDI{value}"
  notes: "Ops: Get, Set. See value table LMOD (table not in source). Platforms: GP3 LED"
- id: lmod
  label: "Lamp Mode"
  kind: action
  command: ":LMOD{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: ldly
  label: "Lamp Auto Switch Delay"
  kind: action
  command: ":LDLY{value}"
  notes: "Ops: Get, Set. Platforms: GP3, GP4"
- id: dual
  label: "Lamp Mode Dual"
  kind: action
  command: ":DUAL{value}"
  notes: "Ops: Get, Set. Use LMOD, this is for legacy support. Platforms: GP3, GP4"
- id: sngl
  label: "Lamp Mode Single"
  kind: action
  command: ":SNGL{value}"
  notes: "Ops: Get, Set. Use LMOD, this is for legacy support. Platforms: GP3, GP4"
- id: laut
  label: "Lamp Mode Auto"
  kind: action
  command: ":LAUT{value}"
  notes: "Ops: Get, Set. Use LMOD, this is for legacy support. Platforms: GP3, GP4"
- id: lact
  label: "Select Lamp In Single Mode"
  kind: action
  command: ":LACT{value}"
  notes: "Ops: Get, Set. Use LMOD, this is for legacy support. Platforms: GP3, GP4"
- id: ldmm
  label: "LED Dim Mode"
  kind: action
  command: ":LDMM{value}"
  notes: "Ops: Get, Set. 0 - standard, 1 - custom. Platforms: GP3 LED"
- id: ldcr
  label: "Custom LED Dim Red"
  kind: action
  command: ":LDCR{value}"
  notes: "Ops: Get, Set. 0-20. Platforms: GP3 LED"
- id: ldcg
  label: "Custom LED Dim Green"
  kind: action
  command: ":LDCG{value}"
  notes: "Ops: Get, Set. 0-20. Platforms: GP3 LED"
- id: ldcb
  label: "Custom LED Dim Blue"
  kind: action
  command: ":LDCB{value}"
  notes: "Ops: Get, Set. 0-20. Platforms: GP3 LED"

# ---- Installation->trigger ----
- id: smod
  label: "Screen Trigger Mode"
  kind: action
  command: ":SMOD{value}"
  notes: "Ops: Get, Set. See value table SMOD (table not in source)"
- id: amod
  label: "Aspect Trigger Mode"
  kind: action
  command: ":AMOD{value}"
  notes: "Ops: Get, Set. See value table AMOD (table not in source). Platforms: GP1, GP3, GP4, GP1_AS3D"

# ---- Installation->EDID ----
- id: edir
  label: "EDID Resolution"
  kind: action
  command: ":EDIR{value}"
  notes: "Ops: Get, Set. See value table EDIR (table not in source). Platforms: GP1, GP2, GP3, GP4"
- id: edit
  label: "EDID Type"
  kind: action
  command: ":EDIT{value}"
  notes: "Ops: Get, Set. See value table EDIT (table not in source). Platforms: GP1, GP2, GP3, GP4"
- id: edmd
  label: "EDID Mailbox Data, Auto Increment"
  kind: action
  command: ":EDMD{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP4"
- id: edmr
  label: "EDID Mailbox Counter Reset"
  kind: action
  command: ":EDMR{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP4"

# ---- Settings ----
- id: fcre
  label: "Factory Reset"
  kind: action
  command: ":FCRE"
  notes: "Ops: Set"
- id: fcrl
  label: "Factory Reset Level"
  kind: action
  command: ":FCRL{value}"
  notes: "Ops: Get, Set"
- id: pinc
  label: "PIN Code"
  kind: action
  command: ":PINC{value}"
  notes: "Ops: Set. Must be run in standby"
- id: code
  label: "Service Code"
  kind: action
  command: ":CODE{value}"
  notes: "Ops: Set"
- id: rcid
  label: "RCID Internal"
  kind: action
  command: ":RCID{value}"
  notes: "Ops: Get, Set"
- id: dpms
  label: "DPMS"
  kind: action
  command: ":DPMS{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable"
- id: dpmt
  label: "DPMS Timeout"
  kind: action
  command: ":DPMT{value}"
  notes: "Ops: Get, Set"
- id: keyb
  label: "Backlight Timeout"
  kind: action
  command: ":KEYB{value}"
  notes: "Ops: Get, Set"

# ---- Profiles ----
- id: umst
  label: "Store User Settings"
  kind: action
  command: ":UMST{value}"
  notes: "Ops: Get, Set. User Settings is replaced by Profile in some software versions"
- id: umrc
  label: "Recall User Settings"
  kind: action
  command: ":UMRC{value}"
  notes: "Ops: Get, Set. User Settings is replaced by Profile in some software versions"
- id: stmo
  label: "Store Motor Position"
  kind: action
  command: ":STMO{value}"
  notes: "Ops: Set. Platforms: GP4"
- id: rcmo
  label: "Recall Motor Position"
  kind: action
  command: ":RCMO{value}"
  notes: "Ops: Set. Platforms: GP4"
- id: prmo
  label: "Profile Mode"
  kind: action
  command: ":PRMO{value}"
  notes: "Ops: Get, Set. 0 - Auto, 1 - Custom, 2 - ISF"
- id: pimo
  label: "Profile ISF Mode"
  kind: action
  command: ":PIMO{value}"
  notes: "Ops: Get, Set. 0 - ISF Day, 1 - ISF Night"
- id: pcen
  label: "Profile Custom Enable"
  kind: action
  command: ":PCEN {value} {target}"
  params:
    - name: value
      type: integer
      description: "0 - disable, 1 - enable"
    - name: target
      type: integer
      description: "Custom profile number (0 - 9)"
  notes: "Ops: Get, Set. Source example: ':PCEN 1 2' enables custom profile number 2"
- id: pcna
  label: "Profile Custom Name"
  kind: action
  command: ":PCNA {value} {target}"
  params:
    - name: value
      type: string
      description: "Profile name as string"
    - name: target
      type: integer
      description: "Custom profile number (0 - 9)"
  notes: "Ops: Get, Set"
- id: pcco
  label: "Profile Custom Connector"
  kind: query
  command: ":PCCO ? {target}"
  params:
    - name: target
      type: integer
      description: "Custom profile number (0 - 9)"
  notes: "Ops: Get. Value: Connector (see Profile Con List, not in source). Source example: ':PCCO ? 2' -> '%001 PCCO 000003'"
- id: prcc
  label: "Profile Custom Current Profile"
  kind: query
  command: ":PRCC?"
  notes: "Ops: Get"
- id: psto
  label: "Profile Custom Store"
  kind: action
  command: ":PSTO{value}"
  notes: "Ops: Set. See value table PSTO (table not in source)"
- id: pcrc
  label: "Profile Custom Recall"
  kind: action
  command: ":PCRC{value}"
  notes: "Ops: Set"
- id: prrc
  label: "Profile Custom Recall Current"
  kind: action
  command: ":PRRC{value}"
  notes: "Ops: Set"
- id: prer
  label: "Profile Custom Erase"
  kind: action
  command: ":PRER{value}"
  notes: "Ops: Set. See value table PRER (table not in source)"
- id: prch
  label: "Current Profile Changed?"
  kind: query
  command: ":PRCH?"
  notes: "Ops: Get. Returns string * (asterisk) if changed"

# ---- Lens control ----
- id: foin
  label: "Focus In"
  kind: action
  command: ":FOIN{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: fout
  label: "Focus Out"
  kind: action
  command: ":FOUT{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: zoin
  label: "Zoom In"
  kind: action
  command: ":ZOIN{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: zout
  label: "Zoom Out"
  kind: action
  command: ":ZOUT{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: irop
  label: "Iris Open"
  kind: action
  command: ":IROP{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: ircl
  label: "Iris Close"
  kind: action
  command: ":IRCL{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: lsdw
  label: "Lens Shift Down"
  kind: action
  command: ":LSDW{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: lsup
  label: "Lens Shift Up"
  kind: action
  command: ":LSUP{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: lslf
  label: "Lens Shift Left"
  kind: action
  command: ":LSLF{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: lsrh
  label: "Lens Shift Right"
  kind: action
  command: ":LSRH{value}"
  notes: "Ops: Set. 1 - Slow, 2 - Medium, 3 - Fast. Platforms: GP3, GP4"
- id: shut
  label: "Shutter"
  kind: action
  command: ":SHUT{value}"
  notes: "Ops: Set. Platforms: GP3, GP4"

# ---- Menu navigate ----
- id: menu
  label: "Menu Navigate Toggle OSD Menu"
  kind: action
  command: ":MENU"
  notes: "Ops: Set"
- id: nvup
  label: "Menu Navigate Up"
  kind: action
  command: ":NVUP"
  notes: "Ops: Set"
- id: nvdw
  label: "Menu Navigate Down"
  kind: action
  command: ":NVDW"
  notes: "Ops: Set"
- id: nvlf
  label: "Menu Navigate Left"
  kind: action
  command: ":NVLF"
  notes: "Ops: Set"
- id: nvrh
  label: "Menu Navigate Right"
  kind: action
  command: ":NVRH"
  notes: "Ops: Set"
- id: nvok
  label: "Menu Navigate Ok"
  kind: action
  command: ":NVOK"
  notes: "Ops: Set"

# ---- Miscellaneous ----
- id: echo
  label: "Communication Response (On/Off)"
  kind: action
  command: ":ECHO{value}"
  notes: "Ops: Set. Toggles auto-acknowledge on/off; value semantics not stated in source"
- id: lang
  label: "Language"
  kind: action
  command: ":LANG{value}"
  notes: "Ops: Get, Set. Platforms: GP1, GP2, GP3, GP4"
- id: osdp
  label: "OSD Menu Position"
  kind: action
  command: ":OSDP{value}"
  notes: "Ops: Get, Set. 0 - standard, 1 - anamorph. Platforms: GP1 Avielo, GP2 Avielo, GP3 Avielo, GP4 Avielo"
- id: snam
  label: "Show OSD Projector ID"
  kind: action
  command: ":SNAM{value}"
  notes: "Ops: Set. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"
- id: sinf
  label: "Show OSD Info"
  kind: action
  command: ":SINF{value}"
  notes: "Ops: Set. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"
- id: mess
  label: "Show OSD Message"
  kind: action
  command: ":MESS{value}"
  notes: "Ops: Get, Set. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"
- id: name
  label: "Projector ID"
  kind: action
  command: ":NAME{value}"
  notes: "Ops: Get, Set. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"

# ---- Medical (GP2 medical only) ----
- id: mdof
  label: "Medical Off"
  kind: action
  command: ":MDOF{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdcl
  label: "Medical Clearbase"
  kind: action
  command: ":MDCL{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdbl
  label: "Medical Bluebase"
  kind: action
  command: ":MDBL{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdfw
  label: "Medical Full White"
  kind: action
  command: ":MDFW{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdcx
  label: "DICOM Clearbase X"
  kind: action
  command: ":MDCX{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdcy
  label: "DICOM Clearbase Y"
  kind: action
  command: ":MDCY{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdbx
  label: "DICOM Bluebase X"
  kind: action
  command: ":MDBX{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"
- id: mdby
  label: "DICOM Bluebase Y"
  kind: action
  command: ":MDBY{value}"
  notes: "Ops: Get, Set. Medical only. Platforms: GP2"

# ---- Thermal ----
- id: thrm
  label: "Thermal Status"
  kind: query
  command: ":THRM?"
  notes: "Ops: Get"
- id: fan1
  label: "Fan Speed 1"
  kind: query
  command: ":FAN1?"
  notes: "Ops: Get"
- id: fan2
  label: "Fan Speed 2"
  kind: query
  command: ":FAN2?"
  notes: "Ops: Get"
- id: fan3
  label: "Fan Speed 3"
  kind: query
  command: ":FAN3?"
  notes: "Ops: Get"
- id: fan4
  label: "Fan Speed 4"
  kind: query
  command: ":FAN4?"
  notes: "Ops: Get"
- id: fan5
  label: "Fan Speed 5"
  kind: query
  command: ":FAN5?"
  notes: "Ops: Get"
- id: fan6
  label: "Fan Speed 6"
  kind: query
  command: ":FAN6?"
  notes: "Ops: Get"
- id: fan7
  label: "Fan Speed 7"
  kind: query
  command: ":FAN7?"
  notes: "Ops: Get"
- id: fan8
  label: "Fan Speed 8"
  kind: query
  command: ":FAN8?"
  notes: "Ops: Get"
- id: sns1
  label: "Sensor Value 1"
  kind: query
  command: ":SNS1?"
  notes: "Ops: Get"
- id: sns2
  label: "Sensor Value 2"
  kind: query
  command: ":SNS2?"
  notes: "Ops: Get"
- id: sns3
  label: "Sensor Value 3"
  kind: query
  command: ":SNS3?"
  notes: "Ops: Get"
- id: sns4
  label: "Sensor Value 4"
  kind: query
  command: ":SNS4?"
  notes: "Ops: Get"
- id: sns5
  label: "Sensor Value 5"
  kind: query
  command: ":SNS5?"
  notes: "Ops: Get"
- id: sns6
  label: "Sensor Value 6"
  kind: query
  command: ":SNS6?"
  notes: "Ops: Get"
- id: sns7
  label: "Sensor Value 7"
  kind: query
  command: ":SNS7?"
  notes: "Ops: Get"
- id: sns8
  label: "Sensor Value 8"
  kind: query
  command: ":SNS8?"
  notes: "Ops: Get"

# ---- Status ----
- id: plat
  label: "Platform Name String"
  kind: query
  command: ":PLAT?"
  notes: "Ops: Get. Extended Protocol"
- id: seri
  label: "Serial Number String"
  kind: query
  command: ":SERI?"
  notes: "Ops: Get. Extended Protocol. Source example: ':seri ?' -> '%001 SERI e00001 07010001'"
- id: modl
  label: "Model Name String"
  kind: query
  command: ":MODL?"
  notes: "Ops: Get. Extended Protocol"
- id: part
  label: "Part Number String"
  kind: query
  command: ":PART?"
  notes: "Ops: Get. Extended Protocol"
- id: sver
  label: "Software Version"
  kind: query
  command: ":SVER?"
  notes: "Ops: Get. Extended Protocol"
- id: swvr
  label: "Software Version"
  kind: query
  command: ":SWVR?"
  notes: "Ops: Get"
- id: acss
  label: "Current Access Level"
  kind: query
  command: ":ACSS?"
  notes: "Ops: Get"
- id: lest
  label: "Status LED State"
  kind: query
  command: ":LEST?"
  notes: "Ops: Get. See value table LEST (table not in source)"
- id: swsn
  label: "SVN SW Revision"
  kind: query
  command: ":SWSN?"
  notes: "Ops: Get. Extended Protocol. Platforms: GP1, GP2, GP3, GP4"

# ---- ZoneCorrection ----
- id: zcen
  label: "ZoneCorrection Enable"
  kind: action
  command: ":ZCEN{value}"
  notes: "Ops: Get, Set. 0 - disable, 1 - enable. Platforms: GP4"

# ---- 3D stereo ----
- id: tdfs
  label: "3D Flash Slave"
  kind: action
  command: ":TDFS{value}"
  notes: "Ops: Set. Platforms: GP1_AS3D"
- id: tdgt
  label: "Glass Type"
  kind: action
  command: ":TDGT{value}"
  notes: "Ops: Get, Set. Platforms: GP1_AS3D"
- id: tdgd
  label: "Genlock Phase Delay"
  kind: action
  command: ":TDGD{value}"
  notes: "Ops: Get, Set. Platforms: GP1_AS3D"
- id: tdsm
  label: "Stereo Mode"
  kind: action
  command: ":TDSM{value}"
  notes: "Ops: Get, Set. Platforms: GP1_AS3D"
- id: tdsc
  label: "Connector Select Slave"
  kind: action
  command: ":TDSC{value}"
  notes: "Ops: Get, Set. Platforms: GP1_AS3D"

# ---- IR control ----
- id: auxl
  label: "IR LED Enable"
  kind: action
  command: ":AUXL{value}"
  notes: "Ops: Get, Set. Platforms: GP3_LED_IR"
- id: auxd
  label: "IR LED Dim"
  kind: action
  command: ":AUXD{value}"
  notes: "Ops: Get, Set. Platforms: GP3_LED_IR"
- id: disl
  label: "Turn Off RGB LEDs"
  kind: action
  command: ":DISL{value}"
  notes: "Ops: Get, Set. Platforms: GP3_LED_IR"

Feedbacks

# Acknowledge format: '%' + ADDRESS (3 bytes) + SPACE + COMMAND (4 bytes) + SPACE + VALUE (6 bytes) + CR (0x0D)
# Example: ":POWR1" -> "%001 POWR 000001"
- id: acknowledge
  type: string
  description: "Acknowledge response: %<addr> <MNEM> <6-byte value> CR. Acknowledge ON by default, toggled by ECHO or per-command modifier A"

# Error responses (returned in place of value when command invalid):
- id: error_access_denied
  type: enum
  values: ["!00001"]
  description: "Access denied - current access level is too low"
- id: error_not_available
  type: enum
  values: ["!00002"]
  description: "Not available - command currently not available (e.g. contrast not available when projector is searching)"
- id: error_not_implemented
  type: enum
  values: ["!00003"]
  description: "Not implemented"
- id: error_value_out_of_range
  type: enum
  values: ["!00004"]
  description: "Value out of range"
- id: extended_info_string
  type: string
  description: "'e00001' - extended info, a description string follows (for values longer than 6 characters)"

# Observable state via queries:
- id: power_state
  type: enum  # UNRESOLVED: POST value table not in source
  description: "Power state via POST query"
- id: signal_status
  type: enum
  values: [searching, locked]
  description: "Signal status via ISTS query: 0 - searching, 1 - locked to source"
- id: thermal_status
  type: string  # UNRESOLVED: value semantics not stated in source
  description: "Thermal status via THRM query"
- id: status_led_state
  type: enum  # UNRESOLVED: LEST value table not in source
  description: "Status LED state via LEST query"
- id: profile_changed
  type: enum
  values: ["*"]
  description: "PRCH query returns * (asterisk) if current profile changed"

Variables

# All settable parameters are modeled as Actions in this spec (one action per source
# command row); no additional variables documented in source.
# UNRESOLVED: value ranges for most level-type commands (BRIG, CNTR, CSAT, VHUE, SHRP,
# VKEY, ...) not stated in source; runtime discovery possible via ?M/?N/?D/?S modifiers.

Events

# UNRESOLVED: no unsolicited notifications documented in source. Some commands generate
# OSD feedback (suppressible via OSDC 0/1), but no push events described.

Macros

# UNRESOLVED: no multi-step sequences described explicitly in source.

Safety

confirmation_required_for: []
interlocks:
  - "Wait 30 seconds after power on before sending next command (explicit source requirement)"
  - "PINC (PIN Code) must be run in standby (explicit source requirement)"
# UNRESOLVED: no other safety warnings or interlock procedures in source.

Notes

Protocol frame: : header (required) + optional address (1-3 bytes) + message body + CR (0x0D) terminator (required). Optional single SPACE between fields; with or without space accepted. Mnemonics not case sensitive.
Timing constraints (source): wait for response before sending next command; minimum 2 s delay before resending if no response; minimum 500 ms between commands; minimum 5 s delay after sending 20 commands.
RS-232 wiring: standard serial cable, 9-pin female to host, 9-pin male to projector; pin 2-2, pin 3-3, pin 5-5.
LAN defaults: DHCP On, IP/subnet/gateway 0.0.0.0 (until assigned), TCP/UDP port 1025, web login username admin password admin (both case sensitive). Web page (browser-based) configures IP settings, port, password, and shows network firmware version; it is not documented as a REST/HTTP control API.
Acknowledges ON by default; ECHO toggles them; modifier A requests acknowledge per command.
Extended Protocol commands (SNAM, SINF, MESS, NAME, PLAT, SERI, MODL, PART, SVER, SWSN) marked as such in source; distinction from base protocol not explained.
Platform note: source maps GP1=F10 series, GP2=F20/evo 20/cineo 20, GP3=F30/cineo 30; GP4 products not enumerated. F32 is not listed, so which commands apply to F32 sx+ is unresolved; all documented commands included for coverage.
Source command table contains duplicate mnemonic rows with conflicting descriptions (SABS, S1T1, S169, SS43, SFLA, SFAR, SLET, SLST, SANL; and LDMM, LPW1, DBDI, LDCR, LDCG, LDCB in the IR-control section) — probable PDF-extraction corruption; deduplicated with both meanings noted.
Referenced value tables (POST, IABS, SABS, GABS, BCCR, BCMO, BCPR, PRES, DSCR, CMTG, ORIE, OSDC, SMOD, AMOD, EDIR, EDIT, PSTO, PRER, LEST, LMOD) are not included in the source document.

Provenance

source_domains:
  - web.archive.org
  - manualslib.com
  - applicationmarket.crestron.com
source_urls:
  - "https://web.archive.org/web/20131222040438/http://www.projectiondesign.com/products/f32-series/_attachment/1663?_ts=13e30ff66f4&download=true"
  - "https://www.manualslib.com/manual/2456229/Projectiondesign-F32-SxPlus.html?page=46"
  - https://applicationmarket.crestron.com/content/Help/ProjectionDesign/projectiondesign_f32_sx_serial_v1_0_help.pdf
  - "https://www.manualslib.com/manual/1133778/Projectiondesign-F32.html?page=46"
retrieved_at: 2026-08-18T12:44:23.806Z
last_checked_at: 2026-08-19T09:40:26.970Z

Verification Summary

verdict: verified
checked_at: 2026-08-19T09:40:26.970Z
matched_actions: 270
action_count: 270
confidence: medium
summary: "All 270 spec mnemonics appear verbatim in the source ASCII command table; transport values (port 1025, baud 19200, 8N1, no flow control) all supported. (12 unresolved item(s) noted in Known Gaps.)"

Known Gaps

- "F32 sx+ platform generation (GP1/GP2/GP3/GP4) not stated in source — per-command applicability to F32 sx+ is unresolved. Referenced value tables (POST, IABS, SABS, GABS, BCCR, BCMO, BCPR, PRES, DSCR, CMTG, ORIE, OSDC, SMOD, AMOD, EDIR, EDIT, PSTO, PRER, LEST, LMOD) are not included in the source."
- "POST value table not in source"
- "value semantics not stated in source"
- "LEST value table not in source"
- "value ranges for most level-type commands (BRIG, CNTR, CSAT, VHUE, SHRP,"
- "no unsolicited notifications documented in source. Some commands generate"
- "no multi-step sequences described explicitly in source."
- "no other safety warnings or interlock procedures in source."
- "firmware version compatibility not stated in source"
- "F32 sx+ platform generation (GP1-GP4) not stated; per-command applicability unknown"
- "value tables referenced but absent from source"
- "UDP control behavior only implied by \"TCP/UDP port\" label; LAN control framing identical to RS-232 assumed from \"connected to either RS232 or LAN ... through this ASCII based protocol\""

From the AI4AV catalog (https://ai4av.net) · ODbL-1.0

Projectiondesign F32 sx+ Control Spec

Summary

Transport

Traits

Actions

Feedbacks

Variables

Events

Macros

Safety

Notes

Provenance

Verification Summary

Known Gaps

Source & contribution

Projectiondesign F32 sx+ Control Spec

Summary

Transport

Traits

Actions

Feedbacks

Variables

Events

Macros

Safety

Notes

Provenance

Verification Summary

Known Gaps

Source & contribution