AI4AVSummary
The Lightware FP-UMX-TPS-TX120-GES4 is a TPS (HDBaseT) transmitter/extender from the UMX-TPS-TX100 series. This spec covers the device's control interfaces: RS-232 (LW2 and LW3 protocols) plus TCP/IP control on ports 10001 (LW2) and 6107 (LW3), as documented in the UMX-TPS-TX100 series user manual.
Transport
protocols:
- serial
- tcp
addressing:
port: 10001 # LW2 protocol port, per source §6.2
serial:
baud_rate: null # UNRESOLVED: no default stated; selectable 4800, 7200, 9600, 14400, 19200, 38400, 57600, 115200
data_bits: null # UNRESOLVED: no default stated; selectable 8 or 9
parity: null # UNRESOLVED: no default stated; selectable None (N), Odd (O), Even (E)
stop_bits: null # UNRESOLVED: no default stated; selectable 1, 1.5, 2
flow_control: UNRESOLVED # UNRESOLVED: flow control not stated in source
auth:
type: UNRESOLVED # source does not state this (was inferred none: no auth procedure in source)
Traits
- powerable # inferred: factory-reset and reboot commands present, not explicit power on/off
- routable # inferred: crosspoint switch commands present (LW2 {<in>@<out>·<layer>}; LW3 CALL /MEDIA/VIDEO/XP:switch)
- queryable # inferred: extensive query commands present (product type, label, firmware, serial, IP status, etc.)
- levelable # inferred: GPIO pin level setting commands present (LW2 {GPIO<pin_nr>=<dir>;<level>})
Actions
# LW2 protocol commands (per source §6) - sent as ASCII strings wrapped in { } over RS-232 (local or TPS link) or TCP port 10001.
- id: lcmd
label: List All Available LW2 Commands
kind: query
command: "{lcmd}"
params: []
- id: i
label: Viewing Product Type
kind: query
command: "{i}"
params: []
- id: label_query
label: Querying the Device Label
kind: query
command: "{label}"
params: []
- id: p_query
label: Querying the Control Protocol
kind: query
command: "{P_?}"
params: []
- id: firmware_version_query
label: Viewing Firmware Version of the CPU
kind: query
command: "{F}"
params: []
- id: ping
label: Connection Test
kind: query
command: "{PING}"
params: []
- id: ct
label: Compile Time
kind: query
command: "{CT}"
params: []
- id: s_query
label: Viewing Serial Number
kind: query
command: "{S}"
params: []
- id: is_query
label: Viewing the Installed Boards
kind: query
command: "{IS}"
params: []
- id: fc_query
label: Viewing Firmware for All Controllers
kind: query
command: "{FC}"
params: []
- id: st_query
label: Querying Health Status
kind: query
command: "{ST}"
params: []
- id: rst
label: Restarting the Device
kind: action
command: "{RST}"
params: []
- id: factory_all
label: Restoring Factory Default Settings
kind: action
command: "{FACTORY=ALL}"
params: []
- id: switch_in_out
label: Switching an Input to the Outputs (LW2)
kind: action
command: "{<in>@<out> <layer>}" # <in>: I1..I6 or 0 (disconnect); <out>: O1; <layer>: A | V | AV
params:
- name: in
type: string
description: Input port (I1..I6 or 0 to disconnect)
- name: out
type: string
description: Output port (e.g. O1)
- name: layer
type: string
description: Signal layer - A (audio), V (video), or AV (both)
- id: mute_output
label: Muting an Output (LW2)
kind: action
command: "{#<out> <layer>}"
params:
- name: out
type: string
description: Output port
- name: layer
type: string
description: A | V | AV
- id: unmute_output
label: Unmuting an Output (LW2)
kind: action
command: "{+<out> <layer>}"
params:
- name: out
type: string
description: Output port
- name: layer
type: string
description: A | V | AV
- id: lock_output
label: Locking an Output (LW2)
kind: action
command: "{#><out> <layer>}"
params:
- name: out
type: string
description: Output port
- name: layer
type: string
description: A | V | AV
- id: unlock_output
label: Unlocking an Output (LW2)
kind: action
command: "{+<<out> <layer>}"
params:
- name: out
type: string
description: Output port
- name: layer
type: string
description: A | V | AV
- id: vc_query
label: Viewing Connection State on the Output (LW2)
kind: query
command: "{VC <layer>}"
params:
- name: layer
type: string
description: A | V | AV
- id: getsize_query
label: Viewing the Crosspoint Size (LW2)
kind: query
command: "{getsize <layer>}"
params:
- name: layer
type: string
description: A | V | AV
- id: as_v_set
label: Changing the Video Autoselect Mode (LW2)
kind: action
command: "{AS_V<out>=<state>;<mode>}"
params:
- name: out
type: string
description: Output port
- name: state
type: string
description: E (enable) or D (disable)
- name: mode
type: string
description: F (first detect) | L (last detect) | P (priority detect)
- id: as_a_set
label: Changing the Audio Autoselect Mode (LW2)
kind: action
command: "{AS_A<out>=<state>;<mode>}"
params:
- name: out
type: string
description: Output port
- name: state
type: string
description: E (enable) or D (disable)
- name: mode
type: string
description: F | L | P
- id: prio_v_set
label: Changing the Video Input Priorities (LW2)
kind: action
command: "{PRIO_V<out>=<in1_prio>;<in2_prio>;…;<inn_prio>}"
params:
- name: out
type: string
description: Output port
- name: priorities
type: string
description: Semicolon-separated priority numbers (0=highest, 5=lowest, 31=skip)
- id: prio_a_set
label: Changing the Audio Input Priorities (LW2)
kind: action
command: "{PRIO_A<out>=<in1_prio>;<in2_prio>;…;<inn_prio>}"
params:
- name: out
type: string
description: Output port
- name: priorities
type: string
description: Semicolon-separated priority numbers (0=highest, 5=lowest, 31=skip)
- id: ip_stat_query
label: Querying the Current IP Status (LW2)
kind: query
command: "{IP_STAT=?}"
params: []
- id: ip_address_set
label: Setting the IP Address (LW2)
kind: action
command: "{IP_ADDRESS=<type>;<ip_address>}"
params:
- name: type
type: string
description: 0 (static) or 1 (DHCP)
- name: ip_address
type: string
description: IPv4 address (four decimal octets)
- id: ip_netmask_set
label: Setting the Subnet Mask (LW2)
kind: action
command: "{IP_NETMASK=<subnet_mask>}"
params:
- name: subnet_mask
type: string
description: Subnet mask
- id: ip_gateway_set
label: Setting the Gateway Address (LW2)
kind: action
command: "{IP_GATEWAY=<gateway_addr>}"
params:
- name: gateway_addr
type: string
description: Gateway address
- id: ip_apply
label: Applying Network Settings (LW2)
kind: action
command: "{ip_apply}"
params: []
- id: eth_enable_set
label: Enabling/Disabling the Ethernet Port (LW2)
kind: action
command: "{ETH_ENABLE=<switch>}"
params:
- name: switch
type: string
description: 0 (disable) or 1 (enable)
- id: rs232_set
label: Setting the RS-232 Mode (LW2)
kind: action
command: "{RS232=<mode>}"
params:
- name: mode
type: string
description: CONTROL | CI (command injection) | PASS (pass-through)
- id: rs232_local_format_set
label: Setting the RS-232 Parameters (LW2, local port)
kind: action
command: "{RS232_LOCAL_FORMAT=<BaudRate>;<DataBit>;<Parity>;<StopBit>}"
params:
- name: BaudRate
type: string
description: 4800 | 7200 | 9600 | 14400 | 19200 | 38400 | 57600 | 115200 | X (no change)
- name: DataBit
type: string
description: 8 | 9 | X (no change)
- name: Parity
type: string
description: N | E | O | X (no change)
- name: StopBit
type: string
description: 1 | 1,5 | 2 | X (no change)
- id: rs232_local_prot_set
label: Setting the Control Protocol of the RS-232 Port (LW2)
kind: action
command: "{RS232_LOCAL_PROT=<protocol>}"
params:
- name: protocol
type: string
description: LW2 | LW3
- id: rs232_link_format_set
label: Setting the Format of the Serial Port Link (LW2, TPS link)
kind: action
command: "{RS232_LINK_FORMAT=<baud_rate>;<data_bit>;<parity>;<stop_bit>}"
params:
- name: baud_rate
type: string
description: As above
- name: data_bit
type: string
description: 8 | 9 | X
- name: parity
type: string
description: N | E | O | X
- name: stop_bit
type: string
description: 1 | 1,5 | 2 | X
- id: rs232_link_prot_set
label: Setting the Protocol of the Serial Port Link (LW2, TPS link)
kind: action
command: "{RS232_LINK_PROT=<protocol>}"
params:
- name: protocol
type: string
description: LW2 | LW3
- id: gpio_set
label: Setting the Level and Direction for Each GPIO Pin (LW2)
kind: action
command: "{GPIO<pin_nr>=<dir>;<level>}"
params:
- name: pin_nr
type: string
description: 0-6
- name: dir
type: string
description: I (input) | O (output)
- name: level
type: string
description: L (low) | H (high) | T (toggle)
# LW3 protocol commands (per source §7) - ASCII tree-path commands terminated with CrLf (\r\n), over TCP port 6107 or RS-232 with LW3 protocol mode. GET/SET/CALL/MAN/OPEN/CLOSE prefixes.
- id: lw3_get_product_name
label: Querying the Product Name (LW3)
kind: query
command: "GET /.ProductName\r\n"
params: []
- id: lw3_set_device_label
label: Setting the Device Label (LW3)
kind: action
command: "SET /MANAGEMENT/UID.DeviceLabel=<Custom_name>\r\n"
params:
- name: Custom_name
type: string
description: Up to 39 ASCII characters
- id: lw3_get_signal_present
label: Querying Signal Present on Input (LW3)
kind: query
command: "GET /MEDIA/VIDEO/I2.SignalPresent\r\n"
params:
- name: input
type: string
description: Input port node (e.g. I1, I2, I3, I4, I5, I6)
- id: lw3_switch
label: Switch Crosspoint (LW3)
kind: action
command: "CALL /MEDIA/VIDEO/XP:switch(I1:O1)\r\n"
params:
- name: connections
type: string
description: Semicolon-separated list of I{port}:O{port} pairs
- id: lw3_set_color_space
label: Set Color Space Mode on Input (LW3)
kind: action
command: "SET /MEDIA/VIDEO/I1.ColorSpaceMode=0\r\n"
params:
- name: input
type: string
description: Input port node
- name: mode
type: string
description: ColorSpaceMode value (0=Auto, etc. - see MAN)
- id: lw3_man
label: Query Property Manual (LW3)
kind: query
command: "MAN /MEDIA/VIDEO/O1.Pwr5vMode\r\n"
params:
- name: path
type: string
description: Property path (e.g. /MEDIA/VIDEO/O1.Pwr5vMode)
- id: lw3_getall_uart
label: GETALL UART Node (LW3)
kind: query
command: "GETALL /MEDIA/UART\r\n"
params: []
- id: lw3_serial_number_query
label: Query Serial Number (LW3)
kind: query
command: "GET /.SerialNumber\r\n"
params: []
- id: lw3_open_subscribe
label: Subscribe to Node (LW3)
kind: action
command: "OPEN /MEDIA/VIDEO\r\n"
params:
- name: node_path
type: string
description: LW3 node path or wildcard (e.g. /MEDIA/VIDEO/*)
- id: lw3_close_unsubscribe
label: Unsubscribe from Node (LW3)
kind: action
command: "CLOSE /MEDIA/VIDEO\r\n"
params:
- name: node_path
type: string
description: LW3 node path or wildcard
# Additional documented commands. Literal source notation is retained:
# · denotes a space (0x20); LW3 commands require the CrLf terminator described above.
# Template parameters must be substituted; example commands use the params shape of the existing entries.
# Model-specific availability stated below does not establish support on FP-UMX-TPS-TX120-GES4.
- id: as_v_query
label: Query Video Autoselect Mode (LW2)
kind: query
command: "{as_v<out>=?}"
params:
- name: out
type: string
description: Output port; range UNRESOLVED
- id: as_a_query
label: Query Audio Autoselect Mode (LW2)
kind: query
command: "{as_a<out>=?}"
params:
- name: out
type: string
description: Output port; range UNRESOLVED
- id: prio_v_query
label: Query Video Input Priorities (LW2)
kind: query
command: "{prio_v<out>=?}"
params:
- name: out
type: string
description: Output port; range UNRESOLVED
- id: prio_a_query
label: Query Audio Input Priorities (LW2)
kind: query
command: "{prio_a<out>=?}"
params:
- name: out
type: string
description: Output port; range UNRESOLVED
- id: ip_address_query
label: Query Stored Static IP Address (LW2)
kind: query
command: "{ip_address=?}"
params: []
- id: ip_gateway_query
label: Query Stored Static Gateway Address (LW2)
kind: query
command: "{ip_gateway=?}"
params: []
- id: rs232_query
label: Query RS-232 Mode (LW2)
kind: query
command: "{RS232=?}"
params: []
- id: rs232_local_format_query
label: Query Local RS-232 Parameters (LW2)
kind: query
command: "{RS232_LOCAL_FORMAT=?}"
params: []
- id: rs232_local_prot_query
label: Query Local RS-232 Control Protocol (LW2)
kind: query
command: "{RS232_LOCAL_PROT=?}"
params: []
- id: lw3_get_active_subscriptions
label: Get Active Subscriptions (LW3)
kind: query
command: "OPEN"
params: []
- id: lw3_get_edid_node_signed
label: Query EDID Node With Signature (LW3)
kind: query
command: "1700#GET /EDID.*"
params:
- name: signature
type: string
description: 4-digit-long hexadecimal value
- id: lw3_get_audio_volume_percent
label: Query Audio Volume Percent (LW3)
kind: query
command: "GET /MEDIA/AUDIO/O3.VolumePercent"
params:
- name: out
type: string
description: Output port; range UNRESOLVED; source example O3
- id: lw3_set_audio_volume_percent
label: Set Audio Volume Percent (LW3)
kind: action
command: "SET /MEDIA/AUDIO/O3.VolumePercent=50.00"
params:
- name: out
type: string
description: Output port; range UNRESOLVED; source example O3
- name: value
type: string
description: UNRESOLVED; source example 50.00
- id: lw3_get_firmware_version
label: Query Firmware Version (LW3)
kind: query
command: "GET /SYS/MB.FirmwareVersion"
params: []
- id: lw3_reset
label: Reset Device (LW3)
kind: action
command: "CALL /SYS:reset()"
params: []
- id: lw3_factory_defaults
label: Restore Factory Default Settings (LW3)
kind: action
command: "CALL /SYS:factoryDefaults()"
params: []
- id: lw3_set_control_lock
label: Set Front Panel Control Lock (LW3)
kind: action
command: "SET /MANAGEMENT/UI.ControlLock=<lock_status>"
params:
- name: lock_status
type: string
description: "1: None; 2: Locked; 3: Force locked"
- id: lw3_set_button_default_function
label: Set Front Panel Button Default Function (LW3)
kind: action
command: "SET /MANAGEMENT/UI/BUTTONS/<btn_id>.DefaultFunctionEnable=<btn_status>"
params:
- name: btn_id
type: string
description: "B1: Video select; B2: Audio select; B2: Show me button; UNRESOLVED: source repeats B2"
- name: btn_status
type: string
description: "Enable | Disable; UNRESOLVED: source table conflicts with example false"
- id: lw3_set_dark_mode
label: Set Dark Mode (LW3)
kind: action
command: "SET /MANAGEMENT/UI/DARKMODE.DarkModeEnable=<status>"
params:
- name: status
type: string
description: true | false
- id: lw3_set_dark_mode_delay
label: Set Dark Mode Delay (LW3)
kind: action
command: "SET /MANAGEMENT/UI/DARKMODE.DarkModeDelay=<delay_time>"
params:
- name: delay_time
type: string
description: Delay time in seconds; range UNRESOLVED
# §7.4.11 and §7.5: TX140K/TX140-Plus from v1.5.0b4;
# WP-UMX-TPS-TX130-Plus-US from v1.5.0b6.
- id: lw3_run_macro
label: Run Macro (LW3)
kind: action
command: "CALL·/CTRL/MACROS:run(<macro_name>)"
params:
- name: macro_name
type: string
description: Unique macro name; length UNRESOLVED
- id: lw3_set_login_password
label: Set Login Password (LW3)
kind: action
command: "CALL·/LOGIN:setPassword(<password>)"
params:
- name: password
type: string
description: UNRESOLVED
- id: lw3_login
label: Log Into Device (LW3)
kind: action
command: "CALL·/LOGIN:login(<password>)"
params:
- name: password
type: string
description: UNRESOLVED
- id: lw3_logout
label: Log Out of Device (LW3)
kind: action
command: "CALL·/LOGIN:logout(<password>)"
params:
- name: password
type: string
description: UNRESOLVED
- id: lw3_set_login_enable
label: Enable or Disable Cleartext Login (LW3)
kind: action
command: "SET /LOGIN.LoginEnable=true"
params:
- name: login_state
type: string
description: true (or 1) | false (or 0); LoggedIn must be true
- id: lw3_get_video_source_status
label: Query Video Source Port Status (LW3)
kind: query
command: "GET /MEDIA/VIDEO/XP.SourcePortStatus"
params: []
- id: lw3_get_video_destination_status
label: Query Video Destination Port Status (LW3)
kind: query
command: "GET /MEDIA/VIDEO/XP.DestinationPortStatus"
params: []
- id: lw3_get_video_connections
label: Query Video Crosspoint Setting (LW3)
kind: query
command: "GET /MEDIA/VIDEO/XP.DestinationConnectionList"
params: []
# Video disconnection is covered by the existing parameterized lw3_switch action.
- id: lw3_get_video_connected_source
label: Query Connected Video Input Port (LW3)
kind: query
command: "GET·/MEDIA/VIDEO/<out>.ConnectedSource"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6); feature from v1.5.0b6 for FP/WP series
- id: lw3_get_video_autoselect
label: Query Video Autoselect Settings (LW3)
kind: query
command: "GET /MEDIA/VIDEO/XP.DestinationPortAutoselect"
params: []
- id: lw3_set_video_autoselect
label: Set Video Autoselect Mode (LW3)
kind: action
command: "CALL·/MEDIA/VIDEO/XP:setDestinationPortAutoselect(<out1_set>;<out2_set>;<…>;<out#_set>)"
params:
- name: settings
type: string
description: "Output settings separated by semicolons; E | D; F | P | L; source examples O1:EP and O1:D"
- id: lw3_get_video_priorities
label: Query Video Input Priorities (LW3)
kind: query
command: "GET /MEDIA/VIDEO/XP.PortPriorityList"
params: []
- id: lw3_set_video_priorities
label: Set Video Input Priorities (LW3)
kind: action
command: 'CALL /MEDIA/VIDEO/XP:setAutoselectionPriority(I1\(O1\):4;I2\(O1\):4)'
params:
- name: priorities
type: string
description: 'Semicolon-separated settings in <in>\(<out>\):<prio> format; Priority number from 0 to 31, equal numbers are allowed (31 means that the port will be skipped from the priority list)'
- id: lw3_mute_video_source
label: Mute Video Input (LW3)
kind: action
command: "CALL·/MEDIA/VIDEO/XP:muteSource(<in>)"
params:
- name: in
type: string
description: I1 | I2 | I3 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_unmute_video_source
label: Unmute Video Input (LW3)
kind: action
command: "CALL·/MEDIA/VIDEO/XP:unmuteSource(<in>)"
params:
- name: in
type: string
description: I1 | I2 | I3 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_lock_video_source
label: Lock Video Input (LW3)
kind: action
command: "CALL·/MEDIA/VIDEO/XP:lockSource(<in>)"
params:
- name: in
type: string
description: I1 | I2 | I3 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_unlock_video_source
label: Unlock Video Input (LW3)
kind: action
command: "CALL·/MEDIA/VIDEO/XP:unlockSource(<in>)"
params:
- name: in
type: string
description: I1 | I2 | I3 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_mute_video_destination
label: Mute Video Output (LW3)
kind: action
command: "CALL·/MEDIA/VIDEO/XP:muteDestination(<out>)"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_unmute_video_destination
label: Unmute Video Output (LW3)
kind: action
command: "CALL·/MEDIA/VIDEO/XP:unmuteDestination(<out>)"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_lock_video_destination
label: Lock Video Output (LW3)
kind: action
command: "CALL·/MEDIA/VIDEO/XP:lockDestination(<out>)"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_unlock_video_destination
label: Unlock Video Output (LW3)
kind: action
command: "CALL·/MEDIA/VIDEO/XP:unlockDestination(<out>)"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_set_input_hdcp
label: Set Input HDCP Capability (LW3)
kind: action
command: "SET·/MEDIA/VIDEO/<in>.HdcpEnable=<logical_value>"
params:
- name: in
type: string
description: Digital video inputs (I2, I3, I4) only; FP-UMX-TPS-TX120 HDMI input is I2 (§11.7.6)
- name: logical_value
type: string
description: true | false
- id: lw3_set_test_pattern_mode
label: Set Test Pattern Generator Mode (LW3)
kind: action
command: "SET·/MEDIA/VIDEO/<in>.FreeRunMode=<mode>"
params:
- name: in
type: string
description: Input port; applicable port range UNRESOLVED
- name: mode
type: string
description: "0: Always off; 1: Always on; 2: Auto"
- id: lw3_set_test_pattern_color
label: Set Test Pattern Color (LW3)
kind: action
command: "SET·/MEDIA/VIDEO/<in>.FreeRunColor=<RGB_code>"
params:
- name: in
type: string
description: Input port; applicable port range UNRESOLVED
- name: rgb_code
type: string
description: RGB color in RR;GG;BB format (separated by semicolons); component ranges UNRESOLVED
- id: lw3_set_test_pattern_resolution
label: Set Test Pattern Resolution (LW3)
kind: action
command: "SET·/MEDIA/VIDEO/<in>.FreeRunResolution=<resolution>"
params:
- name: in
type: string
description: Input port; applicable port range UNRESOLVED
- name: resolution
type: string
description: "0: 640x480p60; 1: 720x480i60; 2: 720x480p60; 3: 720x576i50; 4: 720x576p50; 5: 800x600p60; 6: 1024x768p60; 7: 1280x720p60; 8: 1280x1024p60; 9: 1280x1080i60; 10: 1920x1080p60; 11: 1920x1200p60"
- id: lw3_set_output_hdcp
label: Set Output HDCP Mode (LW3)
kind: action
command: "SET·/MEDIA/VIDEO/<out>.HdcpModeSetting=<HDCP_mode>"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- name: hdcp_mode
type: string
description: "0: Auto; 1: Always"
- id: lw3_set_output_hdmi_mode
label: Set Output HDMI Mode (LW3)
kind: action
command: "SET·/MEDIA/VIDEO/<out>.HdmiModeSetting=<mode>"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- name: mode
type: string
description: "0: Auto; 1: DVI; 2: HDMI 24 bit; 3: HDMI 30 bit; 4: HDMI 36 bit"
- id: lw3_set_output_color_space
label: Set Output Color Space (LW3)
kind: action
command: "SET·/MEDIA/VIDEO/<out>.ColorSpaceSetting=<colorspace>"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- name: colorspace
type: string
description: "0: Auto; 1: RGB; 2: YCbCr 4:4:4; 3: YCbCr 4:2:2"
- id: lw3_set_tps_mode
label: Set TPS Mode (LW3)
kind: action
command: "SET·/REMOTE/<port>.tpsModeSetting=<tps_mode>"
params:
- name: port
type: string
description: UNRESOLVED; source example S1
- name: tps_mode
type: string
description: "A: Auto; H: HDBaseT; L: Longreach; 1: LPPF1; 2: LPPF2"
- id: lw3_get_audio_source_status
label: Query Audio Source Port Status (LW3)
kind: query
command: "GET /MEDIA/AUDIO/XP.SourcePortStatus"
params: []
- id: lw3_get_audio_destination_status
label: Query Audio Destination Port Status (LW3)
kind: query
command: "GET /MEDIA/AUDIO/XP.DestinationPortStatus"
params: []
- id: lw3_get_audio_connections
label: Query Audio Crosspoint Setting (LW3)
kind: query
command: "GET /MEDIA/AUDIO/XP.DestinationConnectionList"
params: []
- id: lw3_switch_audio
label: Switch Audio Input (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:switch(<in>:<out>)"
params:
- name: in
type: string
description: I1 | I2 for FP-UMX-TPS-TX120 series (§11.7.6)
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_get_audio_autoselect
label: Query Audio Autoselect Settings (LW3)
kind: query
command: "GET /MEDIA/AUDIO/XP.DestinationPortAutoselect"
params: []
- id: lw3_set_audio_autoselect
label: Set Audio Autoselect Mode (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:setDestinationPortAutoselect(<out>:<out_set>)"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- name: out_set
type: string
description: "Two-letter code; 1st letter E | D; 2nd letter F | P | L | S; source also documents D to disable without changing other settings"
- id: lw3_get_audio_priorities
label: Query Audio Input Priorities (LW3)
kind: query
command: "GET /MEDIA/AUDIO/XP.PortPriorityList"
params: []
# UNRESOLVED: §7.7.8 has a malformed audio priority command template and a video-path example.
# No corrected audio priority command is inferred.
- id: lw3_mute_audio_source
label: Mute Audio Input (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:muteSource(<in>)"
params:
- name: in
type: string
description: Input port or semicolon-separated inputs; I1 | I2 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_unmute_audio_source
label: Unmute Audio Input (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:unmuteSource(<in>)"
params:
- name: in
type: string
description: Input port or semicolon-separated inputs; I1 | I2 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_lock_audio_source
label: Lock Audio Input (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:lockSource(<in>)"
params:
- name: in
type: string
description: I1 | I2 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_unlock_audio_source
label: Unlock Audio Input (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:unlockSource(<in>)"
params:
- name: in
type: string
description: I1 | I2 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_mute_audio_destination
label: Mute Audio Output (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:muteDestination(<out>)"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_unmute_audio_destination
label: Unmute Audio Output (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:unmuteDestination(<out>)"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_lock_audio_destination
label: Lock Audio Output (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:lockDestination(<out>)"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_unlock_audio_destination
label: Unlock Audio Output (LW3)
kind: action
command: "CALL·/MEDIA/AUDIO/XP:unlockDestination(<out>)"
params:
- name: out
type: string
description: O1 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_set_analog_audio_volume
label: Set Analog Audio Input Volume (LW3)
kind: action
command: "SET·/MEDIA/AUDIO/<in>.Volume=<level>"
params:
- name: in
type: string
description: I1 for FP-UMX-TPS-TX120 series (§11.7.6)
- name: level
type: string
description: between -95.625 dB and 0 dB in step of -0.375 dB
- id: lw3_set_analog_audio_balance
label: Set Analog Audio Input Balance (LW3)
kind: action
command: "SET·/MEDIA/AUDIO/<in>.Balance=<level>"
params:
- name: in
type: string
description: I1 for FP-UMX-TPS-TX120 series (§11.7.6)
- name: level
type: string
description: 0 means left balance, 100 means right balance, step is 1. Center is 50 (default).
- id: lw3_set_event_condition
label: Set Event Condition (LW3)
kind: action
command: "SET·/EVENTS/E<loc>.Condition=<expression>"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- name: expression
type: string
description: "<node_path>.<property>=<value>; property change can use a trailing ?; linked event number without E, or up to four event numbers joined by &; combined links and change-to-anything require the firmware versions stated in §7.9"
- id: lw3_set_event_condition_inverted
label: Invert Event Condition (LW3)
kind: action
command: "SET /EVENTS/E2.ConditionInverted=true"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- name: value
type: string
description: true; other accepted values UNRESOLVED
- id: lw3_set_event_action
label: Set Event Action (LW3)
kind: action
command: "SET·/EVENTS/E<loc>.Action=<expression>"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- name: expression
type: string
description: "<node_path>.<property_or_method>=<value>; use dot for both properties and methods, no method brackets; alternatively linked event number without E, or macro name where supported (§7.9.6)"
- id: lw3_get_macro_name
label: Query Macro Name (LW3)
kind: query
command: "GET /CTRL/MACROS.<id>"
params:
- name: id
type: string
description: UNRESOLVED; macro feature availability per §7.9.6
- id: lw3_set_event_condition_timeout
label: Set Event Condition Delay (LW3)
kind: action
command: "SET·/EVENTS/E<loc>.ConditionTimeout=<time>"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- name: time
type: string
description: Seconds; 0 means no delay; range UNRESOLVED
- id: lw3_set_event_condition_end_check
label: Set Event Condition End Check (LW3)
kind: action
command: "SET·/EVENTS/E<loc>.ConditionEndCheck=<true/false>"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- name: value
type: string
description: true | false
- id: lw3_set_event_condition_timeout_continuous
label: Set Continuous Event Condition Delay (LW3)
kind: action
command: "SET·/EVENTS/E<loc>.ConditionTimeoutContinuous=<true/false>"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- name: value
type: string
description: true | false
- id: lw3_set_event_condition_timeout_pending
label: Set Event Condition Timeout Pending (LW3)
kind: action
command: "SET /EVENTS/E1.ConditionTimeoutPending=true"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- name: value
type: string
description: "UNRESOLVED: source example sets true, while the summary specifies ConditionEndCheck for this delay type"
- id: lw3_set_event_name
label: Set Event Name (LW3)
kind: action
command: "SET·/EVENTS/E<loc>.Name=<string>"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- name: string
type: string
description: letters (A-Z) and (a-z), numbers (0-9), special characters hyphen ( - ), underscore ( _ ), and space ( ) up to 20 characters
- id: lw3_set_event_enabled
label: Enable or Disable Event (LW3)
kind: action
command: "SET·/EVENTS/E<loc>.Enabled=<true/false>"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- name: value
type: string
description: true (or 1) | false (or 0)
# §7.10.4 and §7.10.6: condition triggering is limited to TX140K/TX140-Plus
# from v1.5.0b4 and WP-UMX-TPS-TX130-Plus-US from v1.5.0b6.
- id: lw3_trigger_event_condition
label: Trigger Event Condition (LW3)
kind: action
command: "CALL·/EVENTS/E<loc>:triggerCondition(1)"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- id: lw3_get_event_condition_count
label: Query Event Condition Counter (LW3)
kind: query
command: "GET·/EVENTS/E<loc>.ConditionCount"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- id: lw3_get_event_trigger_count
label: Query Event Condition Trigger Counter (LW3)
kind: query
command: "GET·/EVENTS/E<loc>.ExternalConditionTriggerCount"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
- id: lw3_test_event_action
label: Test Event Action (LW3)
kind: action
command: "CALL·/EVENTS/E<loc>:ActionTest(1)"
params:
- name: loc
type: string
description: Event location; range UNRESOLVED
# §7.11: variables are limited to TX140K/TX140-Plus from v1.5.0b4
# and WP-UMX-TPS-TX130-Plus-US from v1.5.0b6.
- id: lw3_set_variable_value
label: Assign Variable Value (LW3)
kind: action
command: "SET·/CTRL/VARS/V<loc>.Value=<value>"
params:
- name: loc
type: string
description: 1-30
- name: value
type: string
description: String can be max 15 characters. Numeric variable is defined between -2147483648 and 2147483647.
- id: lw3_get_variable_value
label: Query Variable Value (LW3)
kind: query
command: "GET /CTRL/VARS/V1.Value"
params:
- name: loc
type: string
description: 1-30
- id: lw3_add_variable
label: Add to Variable (LW3)
kind: action
command: "CALL·/CTRL/VARS/V<loc>:add(<operand>;<min>;<max>)"
params:
- name: loc
type: string
description: 1-30
- name: operand
type: string
description: Integer; Negative value is also accepted; range UNRESOLVED
- name: min
type: string
description: Integer; optional; Negative value is also accepted; range UNRESOLVED
- name: max
type: string
description: Integer; optional; Negative value is also accepted; range UNRESOLVED
- id: lw3_cycle_variable
label: Cycle Variable Value (LW3)
kind: action
command: "CALL·/CTRL/VARS/V<loc>:cycle(<operand>;<min>;<max>)"
params:
- name: loc
type: string
description: 1-30
- name: operand
type: string
description: Integer; Negative value is also accepted; range UNRESOLVED
- name: min
type: string
description: Integer; optional; Negative value is also accepted; range UNRESOLVED
- name: max
type: string
description: Integer; optional; Negative value is also accepted; range UNRESOLVED
- id: lw3_case_variable
label: Convert Variable by Intervals (LW3)
kind: action
command: "CALL·/CTRL/VARS/V<loc>:case(<min> <max> <val>;)"
params:
- name: loc
type: string
description: 1-30
- name: cases
type: string
description: Space-separated Integer min, max, val; interval groups divided by semicolons; Up to 16 cases can be defined; integer ranges UNRESOLVED
- id: lw3_scan_variable
label: Scan Property Into Variable (LW3)
kind: action
command: "CALL·/CTRL/VARS/V<loc>:scanf(<path>.<property>;<pattern>)"
params:
- name: loc
type: string
description: 1-30
- name: path
type: string
description: LW3 node path; range UNRESOLVED
- name: property
type: string
description: LW3 property; range UNRESOLVED
- name: pattern
type: string
description: '%s | %<number>s | %c | %<number>c | %[<characters>] | %[^<characters>] | %* | <custom_text>; patterns can be combined; escape the % character'
- id: lw3_reformat_variable
label: Reformat Variable Value (LW3)
kind: action
command: "CALL·/CTRL/VARS/V<loc>:printf(<prefix>%s<postfix>)"
params:
- name: loc
type: string
description: 1-30
- name: prefix
type: string
description: Custom ASCII characters; optional; resulting value limited to 15 characters
- name: postfix
type: string
description: Custom ASCII characters; optional; resulting value limited to 15 characters
- id: lw3_set_dhcp
label: Set DHCP State (LW3)
kind: action
command: "SET·/MANAGEMENT/NETWORK.DhcpEnabled=<dhcp_status>"
params:
- name: dhcp_status
type: string
description: true | false; applySettings must be called to apply changes
- id: lw3_set_static_ip
label: Set Static IP Address (LW3)
kind: action
command: "SET·/MANAGEMENT/NETWORK.StaticIpAddress=<IP_address>"
params:
- name: ip_address
type: string
description: IP address; range UNRESOLVED; applySettings must be called to apply changes
- id: lw3_set_static_netmask
label: Set Static Subnet Mask (LW3)
kind: action
command: "SET·/MANAGEMENT/NETWORK.StaticNetworkMask=<netmask>"
params:
- name: netmask
type: string
description: Subnet mask; range UNRESOLVED; applySettings must be called to apply changes
- id: lw3_set_static_gateway
label: Set Static Gateway Address (LW3)
kind: action
command: "SET·/MANAGEMENT/NETWORK.StaticGatewayAddress=<gw_address>"
params:
- name: gw_address
type: string
description: Gateway address; range UNRESOLVED; applySettings must be called to apply changes
- id: lw3_apply_network_settings
label: Apply Network Settings (LW3)
kind: action
command: "CALL /MANAGEMENT/NETWORK:applySettings(1)"
params: []
# UNRESOLVED: §7.12.5 uses ApplySettings, while §7.12.1–7.12.4 use applySettings.
# These are one entry under the requested case-insensitive comparison rule.
# §7.13.1–7.13.4: MAC/service filters are limited to TX140K/TX140-Plus
# from v1.5.0b4 and WP-UMX-TPS-TX130-Plus-US from v1.5.0b6.
- id: lw3_set_mac_filter_entry
label: Set MAC Filter Entry (LW3)
kind: action
command: "SET·/MANAGEMENT/MACFILTER.MACaddress<loc>=<MAC_address>;<receive>;<send>;<name>"
params:
- name: loc
type: string
description: 1-8; default values of 1, 2 and 3 ensure access after enabling the MAC filter
- name: mac_address
type: string
description: Hex format, divided by a colon
- name: receive
type: string
description: false (or 0) | true (or 1)
- name: send
type: string
description: false (or 0) | true (or 1)
- name: name
type: string
description: Any string; optional; Up to 5 ASCII characters (longer names are truncated)
- id: lw3_enable_mac_filter
label: Enable MAC Filter (LW3)
kind: action
command: "SET /MANAGEMENT/MACFILTER.FilterEnable=true"
params:
- name: value
type: string
description: true; other accepted values UNRESOLVED
- id: lw3_set_lw2_service_enabled
label: Set LW2 Control Port State (LW3)
kind: action
command: "SET·/MANAGEMENT/SERVICEFILTER.Lw2Enabled=<port_mode>"
params:
- name: port_mode
type: string
description: UNRESOLVED; source example false blocks LW2
- id: lw3_set_http_service_enabled
label: Set HTTP Port State (LW3)
kind: action
command: "SET·/MANAGEMENT/SERVICEFILTER.HttpEnabled=<port_mode>"
params:
- name: port_mode
type: string
description: "UNRESOLVED; source example true; §7.13.4 repeats this same token for HTTP posts"
- id: lw3_wake_on_lan
label: Wake Computer Over Ethernet (LW3)
kind: action
command: "CALL·/MEDIA/ETHERNET:wakeOnLan(MAC_address)"
params:
- name: mac_address
type: string
description: "MAC address; source example AA:BB:CC:22:14:FF; feature from v1.5.0b4 for UMX and v1.5.0b6 for FP/WP"
- id: lw3_set_hostname
label: Set Hostname (LW3)
kind: action
command: "SET·/MANAGEMENT/NETWORK.HostName=<unique_name>"
params:
- name: unique_name
type: string
description: 1-64 characters; elements of the English alphabet and numbers; Hyphen (-) and dot (.) accepted except as last character; feature from v1.5.0b4 for UMX and v1.5.0b6 for FP/WP
- id: lw3_send_tcp_message
label: Send TCP Message (LW3)
kind: action
command: "CALL·/MEDIA/ETHERNET:tcpMessage(<IP_address>:<port_no>=<message>)"
params:
- name: ip_address
type: string
description: Target IP address; range UNRESOLVED
- name: port_no
type: string
description: Target port number; range UNRESOLVED
- name: message
type: string
description: ASCII-format message; allows escaping control characters; length UNRESOLVED
- id: lw3_send_tcp_text
label: Send TCP Text (LW3)
kind: action
command: "CALL·/MEDIA/ETHERNET:tcpText(<IP_address>:<port_no>=<text>)"
params:
- name: ip_address
type: string
description: Target IP address; range UNRESOLVED
- name: port_no
type: string
description: Target port number; range UNRESOLVED
- name: text
type: string
description: ASCII-format text; does not allow escaping or inserting control characters; length UNRESOLVED
- id: lw3_send_tcp_binary
label: Send TCP Binary Message (LW3)
kind: action
command: "CALL /MEDIA/ETHERNET:tcpBinary(192.168.0.103:6107=0100000061620000cdcc2c40)"
params:
- name: ip_address
type: string
description: Target IP address; range UNRESOLVED
- name: port_no
type: string
description: Target port number; range UNRESOLVED
- name: hex_message
type: string
description: Hexadecimal format without spaces or separators; length UNRESOLVED; literal follows the colon-form example in §7.14.3
- id: lw3_send_udp_message
label: Send UDP Message (LW3)
kind: action
command: "CALL·/MEDIA/ETHERNET:udpMessage(<IP_address>:<port_no>=<message>)"
params:
- name: ip_address
type: string
description: Target IP address; range UNRESOLVED
- name: port_no
type: string
description: Target port number; range UNRESOLVED
- name: message
type: string
description: ASCII-format message; allows escaping control characters; length UNRESOLVED
- id: lw3_send_udp_text
label: Send UDP Text (LW3)
kind: action
command: "CALL·/MEDIA/ETHERNET:udpText(<IP_address>:<port_no>=<text>)"
params:
- name: ip_address
type: string
description: Target IP address; range UNRESOLVED
- name: port_no
type: string
description: Target port number; range UNRESOLVED
- name: text
type: string
description: ASCII-format text; does not allow escaping or inserting control characters; length UNRESOLVED
- id: lw3_send_udp_binary
label: Send UDP Binary Message (LW3)
kind: action
command: "CALL·/MEDIA/ETHERNET:udpBinary(<IP_address>:<port_no>=<HEX_message>)"
params:
- name: ip_address
type: string
description: Target IP address; range UNRESOLVED
- name: port_no
type: string
description: Target port number; range UNRESOLVED
- name: hex_message
type: string
description: Hexadecimal format without spaces or separators; length UNRESOLVED
# §7.15 and §7.16: HTTP clients and TCP recognizer are limited to TX140K/TX140-Plus
# from v1.5.0b4 and WP-UMX-TPS-TX130-Plus-US from v1.5.0b6.
- id: lw3_set_http_server_ip
label: Set HTTP Target IP Address (LW3)
kind: action
command: "SET·/CTRL/HTTP/C1.ServerIP=<IP_address>"
params:
- name: ip_address
type: string
description: Target server IP address; range UNRESOLVED
- id: lw3_set_http_server_port
label: Set HTTP Target TCP Port (LW3)
kind: action
command: "SET·/CTRL/HTTP/C1.ServerPort=<port_no>"
params:
- name: port_no
type: string
description: Target TCP port number; range UNRESOLVED
- id: lw3_set_http_target_path
label: Set HTTP Target Path (LW3)
kind: action
command: "SET·/CTRL/HTTP/C1.File=<path>"
params:
- name: path
type: string
description: Target post/put path; length UNRESOLVED
- id: lw3_set_http_header
label: Set HTTP Message Header (LW3)
kind: action
command: "SET·/CTRL/HTTP/C1.Header=<header_text>"
params:
- name: header_text
type: string
description: HTTP header text; length UNRESOLVED
- id: lw3_http_post
label: Send HTTP Post Message (LW3)
kind: action
command: "CALL·/CTRL/HTTP/C1:post(<body_text>)"
params:
- name: body_text
type: string
description: HTTP body text; length UNRESOLVED; HTTPS not supported
- id: lw3_http_put
label: Send HTTP Put Message (LW3)
kind: action
command: "CALL·/CTRL/HTTP/C1:put(<body_text>)"
params:
- name: body_text
type: string
description: HTTP body text; length UNRESOLVED; HTTPS not supported
- id: lw3_set_tcp_server_ip
label: Set TCP Server IP Address (LW3)
kind: action
command: "SET·/CTRL/TCP/C<loc>.ServerIP=<IP_address>"
params:
- name: loc
type: string
description: 1, 2 or 3
- name: ip_address
type: string
description: TCP server IP address; range UNRESOLVED
- id: lw3_set_tcp_server_port
label: Set TCP Server Port (LW3)
kind: action
command: "SET·/CTRL/TCP/C<loc>.ServerPort=<port_no>"
params:
- name: loc
type: string
description: 1, 2 or 3
- name: port_no
type: string
description: TCP server port number; range UNRESOLVED
- id: lw3_connect_tcp_server
label: Connect to TCP Server (LW3)
kind: action
command: "CALL·/CTRL/TCP/C<loc>:connect()"
params:
- name: loc
type: string
description: 1, 2 or 3
- id: lw3_disconnect_tcp_server
label: Disconnect From TCP Server (LW3)
kind: action
command: "CALL·/CTRL/TCP/C<loc>:disconnect()"
params:
- name: loc
type: string
description: 1, 2 or 3
- id: lw3_set_tcp_delimiter
label: Set TCP Recognizer Delimiter (LW3)
kind: action
command: "SET·/CTRL/TCP/C<loc>.DelimiterHex=<delimiter>"
params:
- name: loc
type: string
description: 1, 2 or 3
- name: delimiter
type: string
description: "max. 8 character long (16 hex digits) in hex format; UNRESOLVED: source length wording is inconsistent"
- id: lw3_set_tcp_timeout
label: Set TCP Recognizer Timeout (LW3)
kind: action
command: "SET·/CTRL/TCP/C<loc>.TimeOut=<timeout>"
params:
- name: loc
type: string
description: 1, 2 or 3
- name: timeout
type: string
description: milliseconds; 0 means the timeout is disabled, min. value is 10; maximum UNRESOLVED
- id: lw3_get_tcp_rx
label: Query Last Recognized TCP Message (LW3)
kind: query
command: "GET·/CTRL/TCP/C<loc>.Rx"
params:
- name: loc
type: string
description: 1, 2 or 3; recognized string can be max. 128 bytes long
- id: lw3_get_tcp_rx_hex
label: Query Last Recognized TCP Message in Hex (LW3)
kind: query
command: "GET·/CTRL/TCP/C<loc>.RxHex"
params:
- name: loc
type: string
description: 1, 2 or 3
- id: lw3_clear_tcp_rx
label: Clear Stored Recognized TCP Messages (LW3)
kind: action
command: "CALL·/CTRL/TCP/C<loc>:clear()"
params:
- name: loc
type: string
description: 1, 2 or 3; clears Rx, RxHex and Hash
- id: lw3_get_tcp_active_rx
label: Query Active Recognized TCP Message (LW3)
kind: query
command: "GET·/CTRL/TCP/C<loc>.ActiveRx"
params:
- name: loc
type: string
description: 1, 2 or 3; recognized string is max. 12-byte-long
- id: lw3_get_tcp_active_rx_hex
label: Query Active Recognized TCP Message in Hex (LW3)
kind: query
command: "GET·/CTRL/TCP/C<loc>.ActiveRxHex"
params:
- name: loc
type: string
description: 1, 2 or 3
- id: lw3_set_tcp_active_timeout
label: Set TCP Recognizer Active Timeout (LW3)
kind: action
command: "SET·/CTRL/TCP/C<loc>.ActivePropertyTimeout=<a_timeout>"
params:
- name: loc
type: string
description: 1, 2 or 3
- name: a_timeout
type: string
description: active timeout value (ms) between 0 and 255; default 50ms
- id: lw3_set_tcp_action_trigger
label: Set TCP Recognizer Event Action (LW3)
kind: action
command: "SET·/CTRL/TCP/C<loc>.ActionTrigger=<event_nr>"
params:
- name: loc
type: string
description: 1, 2 or 3
- name: event_nr
type: string
description: Number (location) of the linked Event Action without letter E; range UNRESOLVED
# §7.19.10 repeats the TCP ActionTrigger token; no UART ActionTrigger path is inferred.
- id: lw3_set_uart_protocol
label: Set RS-232 Control Protocol (LW3)
kind: action
command: "SET·/MEDIA/UART/<port>.ControlProtocol=<protocol>"
params:
- name: port
type: string
description: P1 | P2 (§11.7.6)
- name: protocol
type: string
description: "0: LW2 protocol; 1: LW3 protocol"
- id: lw3_set_uart_baudrate
label: Set RS-232 Baud Rate (LW3)
kind: action
command: "SET·/MEDIA/UART/<port>.Baudrate=<baudrate>"
params:
- name: port
type: string
description: P1 | P2 (§11.7.6)
- name: baudrate
type: string
description: "0: 4800; 1: 7200; 2: 9600; 3: 14400; 4: 19200; 5: 38400; 6: 57600; 7: 115200"
- id: lw3_set_uart_data_bits
label: Set RS-232 Data Bits (LW3)
kind: action
command: "SET·/MEDIA/UART/<port>.DataBits=<databits>"
params:
- name: port
type: string
description: P1 | P2 (§11.7.6)
- name: databits
type: string
description: 8 | 9
- id: lw3_set_uart_stop_bits
label: Set RS-232 Stop Bits (LW3)
kind: action
command: "SET·/MEDIA/UART/<port>.StopBits=<stopbits>"
params:
- name: port
type: string
description: P1 | P2 (§11.7.6)
- name: stopbits
type: string
description: "0: 1; 1: 1,5; 2: 2"
- id: lw3_set_uart_parity
label: Set RS-232 Parity (LW3)
kind: action
command: "SET /MEDIA/UART/P1.Parity=0"
params:
- name: port
type: string
description: P1 | P2 (§11.7.6)
- name: parity
type: string
description: "0: None; 1: Odd; 2: Even"
- id: lw3_set_uart_mode
label: Set RS-232 Operation Mode (LW3)
kind: action
command: "SET·/MEDIA/UART/<port>.Rs232Mode=<mode>"
params:
- name: port
type: string
description: P1 | P2 (§11.7.6); operation mode is mirrored between ports
- name: mode
type: string
description: "0: Pass-through; 1: Control; 2: Command injection"
- id: lw3_set_uart_command_injection
label: Enable or Disable RS-232 Command Injection (LW3)
kind: action
command: "SET·/MEDIA/UART/<port>.CommandInjectionEnable=<logical_value>"
params:
- name: port
type: string
description: P1 | P2 (§11.7.6)
- name: logical_value
type: string
description: true | false
- id: lw3_send_uart_message
label: Send RS-232 Message (LW3)
kind: action
command: "CALL·/MEDIA/UART/P1:sendMessage(<message>)"
params:
- name: message
type: string
description: ASCII-format message; allows escaping control characters; length UNRESOLVED
- id: lw3_send_uart_text
label: Send RS-232 Text (LW3)
kind: action
command: "CALL·/MEDIA/UART/P1:sendText(<message>)"
params:
- name: message
type: string
description: ASCII-format message; length UNRESOLVED
- id: lw3_send_uart_binary
label: Send RS-232 Binary Message (LW3)
kind: action
command: "CALL·/MEDIA/UART/P1:sendBinaryMessage(<message>)"
params:
- name: message
type: string
description: Hexadecimal format; does not require escaping control and non-printable characters; length UNRESOLVED
# §7.19: UART recognizer is limited to TX140K/TX140-Plus from v1.3.0b11
# and WP-UMX-TPS-TX130-Plus from v1.4.0b8.
- id: lw3_set_uart_recognizer_enabled
label: Enable or Disable RS-232 Recognizer (LW3)
kind: action
command: "SET·/MEDIA/UART/<serial_port>.RecognizerEnable=<recognizer_enable>"
params:
- name: serial_port
type: string
description: P1, P2
- name: recognizer_enable
type: string
description: true | false
- id: lw3_set_uart_recognizer_delimiter
label: Set RS-232 Recognizer Delimiter (LW3)
kind: action
command: "SET·/MEDIA/UART/RECOGNIZER.DelimiterHex=<delimiter>"
params:
- name: delimiter
type: string
description: "max. 8 characters long (or 16 hex digits) in hex format; UNRESOLVED: source length wording is inconsistent"
- id: lw3_set_uart_recognizer_timeout
label: Set RS-232 Recognizer Timeout (LW3)
kind: action
command: "SET·/MEDIA/UART/RECOGNIZER.TimeOut=<timeout>"
params:
- name: timeout
type: string
description: milliseconds; 0 means the timeout is disabled, min. value is 10; maximum UNRESOLVED
- id: lw3_get_uart_rx
label: Query Last Recognized RS-232 Message (LW3)
kind: query
command: "GET /MEDIA/UART/RECOGNIZER.Rx"
params: []
- id: lw3_get_uart_rx_hex
label: Query Last Recognized RS-232 Message in Hex (LW3)
kind: query
command: "GET /MEDIA/UART/RECOGNIZER.RxHex"
params: []
- id: lw3_clear_uart_rx
label: Clear Stored Recognized RS-232 Messages (LW3)
kind: action
command: "CALL /MEDIA/UART/RECOGNIZER:clear()"
params: []
- id: lw3_get_uart_active_rx
label: Query Active Recognized RS-232 Message (LW3)
kind: query
command: "GET /MEDIA/UART/RECOGNIZER.ActiveRx"
params: []
- id: lw3_get_uart_active_rx_hex
label: Query Active Recognized RS-232 Message in Hex (LW3)
kind: query
command: "GET /MEDIA/UART/RECOGNIZER.ActiveRxHex"
params: []
- id: lw3_set_uart_active_timeout
label: Set RS-232 Recognizer Active Timeout (LW3)
kind: action
command: "SET·/MEDIA/UART/RECOGNIZER.ActivePropertyTimeout=<a_timeout>"
params:
- name: a_timeout
type: string
description: active timeout value (ms) between 0 and 255; default 50ms
# §7.20: CEC is limited to TX140K/TX140-Plus from v1.3.0b11
# and WP-UMX-TPS-TX130-Plus-US from v1.4.0b8.
# sendClick requires v1.5.0b4 for UMX and v1.5.0b6 for FP/WP.
- id: lw3_send_cec_click
label: Send CEC Press and Release Command (LW3)
kind: action
command: "CALL·/MEDIA/CEC/<port>:sendClick(<command>)"
params:
- name: port
type: string
description: Video input or output port; applicable range UNRESOLVED in §7.20.1
- name: command
type: string
description: ok | back | up | down | left | right | root_menu | setup_menu | contents_menu | favorite_menu | media_top_menu | media_context_menu | number_0 | number_1 | number_2 | number_3 | number_4 | number_5 | number_6 | number_7 | number_8 | number_9 | dot | enter | clear | channel_up | channel_down | sound_select | input_select | display_info | power_legacy | page_up | page_down | volume_up | volume_down | mute_toggle | mute | unmute | play | stop | pause | record | rewind | fast_forward | eject | skip_forward | skip_backward | 3d_mode | stop_record | pause_record | play_forward | play_reverse | select_next_media | select_media_1 | select_media_2 | select_media_3 | select_media_4 | select_media_5 | power_toggle | power_on | power_off | stop_function | f1 | f2 | f3 | f4
- id: lw3_send_cec_command
label: Send CEC Command (LW3)
kind: action
command: "CALL·/MEDIA/CEC/<port>:send(<command>)"
params:
- name: port
type: string
description: I1-I4 | O1-O2
- name: command
type: string
description: image_view_on | standby | text_view_on | active_source | get_cec_version | set_osd | clear_osd | give_power_status; set_osd requires setting OsdString first
- id: lw3_set_cec_osd_string
label: Set CEC OSD String (LW3)
kind: action
command: "SET·/MEDIA/CEC/<port>.OsdString=<text>"
params:
- name: port
type: string
description: I1-I4 | O1-O2
- name: text
type: string
description: Letters (A-Z) and (a-z), hyphen (-), underscore (_), numbers (0-9), and dot (.). Max length 14 characters.
- id: lw3_send_cec_hex
label: Send CEC Command in Hex (LW3)
kind: action
command: "CALL·/MEDIA/CEC/<port>:sendHex(<hex_code>)"
params:
- name: port
type: string
description: I1-I4 | O1-O2
- name: hex_code
type: string
description: Max. 30 characters (15 bytes) in hexadecimal format.
- id: lw3_get_cec_last_message
label: Query Last Received CEC Message (LW3)
kind: query
command: "GET /MEDIA/CEC/<port>.LastReceivedMessage"
params:
- name: port
type: string
description: I1-I4 or O1-O2
- id: lw3_set_ir_command_injection
label: Enable or Disable IR Command Injection (LW3)
kind: action
command: "SET·/MEDIA/IR/<port>.CommandInjectionEnable=true|false"
params:
- name: port
type: string
description: IR port; applicable range UNRESOLVED; source example S1
- name: value
type: string
description: true | false
- id: lw3_set_ir_modulation
label: Enable or Disable IR Output Modulation (LW3)
kind: action
command: "SET·/MEDIA/IR/<port>.EnableModulation=true|false"
params:
- name: port
type: string
description: IR output port; applicable range UNRESOLVED; source example D1
- name: value
type: string
description: true | false; default true
# §7.22: Pronto sending is limited to TX140K, TX140-Plus and WP-UMX-TPS-TX130-Plus-US.
- id: lw3_send_pronto_hex
label: Send Little Endian Pronto Hex (LW3)
kind: action
command: "CALL·/MEDIA/IR/<output_port>:sendProntoHex(<hex_code>)"
params:
- name: output_port
type: string
description: "Local Infra output: D1; TPS Infra output: D2"
- name: hex_code
type: string
description: maximum 765-character-long code in hexadecimal format (0-9; A-F; a-f) without space character in little-endian system; exactly one complete pronto hex message
- id: lw3_send_pronto_hex_big_endian
label: Send Big Endian Pronto Hex (LW3)
kind: action
command: "CALL·/MEDIA/IR/<output_port>:sendProntoHexBigEndian(<hex_code>)"
params:
- name: output_port
type: string
description: "Local Infra output: D1; TPS Infra output: D2"
- name: hex_code
type: string
description: maximum 765-character-long code in hexadecimal format (0-9; A-F; a-f) without space character in big-endian system; exactly one complete pronto hex message
# UNRESOLVED: §7.23 says GPIO port number 1..8, conflicting with the seven-pin descriptions.
# GPIO support on FP-UMX-TPS-TX120-GES4 is not established.
- id: lw3_set_gpio_direction
label: Set GPIO Pin Direction (LW3)
kind: action
command: "SET·/MEDIA/GPIO/<port>.Direction=<direction>"
params:
- name: port
type: string
description: GPIO port number (1..8). Example P1; model applicability UNRESOLVED
- name: direction
type: string
description: I | O
- id: lw3_set_gpio_output
label: Set GPIO Pin Output Level (LW3)
kind: action
command: "SET·/MEDIA/GPIO/<port>.Output=<value>"
params:
- name: port
type: string
description: GPIO port number (1..8). Example P1; model applicability UNRESOLVED
- name: value
type: string
description: H | L
- id: lw3_toggle_gpio
label: Toggle GPIO Pin Level (LW3)
kind: action
command: "CALL·/MEDIA/GPIO/<port>:toggle()"
params:
- name: port
type: string
description: GPIO port number (1..8). Example P1; model applicability UNRESOLVED
- id: lw3_get_edid_status
label: Query Emulated EDIDs (LW3)
kind: query
command: "GET /EDID.EdidStatus"
params: []
- id: lw3_get_dynamic_edid_validity
label: Query Dynamic EDID Validity (LW3)
kind: query
command: "GET·/EDID/D/<dynamic>.Validity"
params:
- name: dynamic
type: string
description: Dynamic EDID memory index; example D1; range UNRESOLVED
- id: lw3_get_user_edid_resolution
label: Query User EDID Preferred Resolution (LW3)
kind: query
command: "GET·/EDID/U/<user>.PreferredResolution"
params:
- name: user
type: string
description: User EDID memory index; example U1; range UNRESOLVED
- id: lw3_switch_edid
label: Emulate EDID on Input Port (LW3)
kind: action
command: "CALL·/EDID:switch(<dynamic|user|factory>:<emulated>)"
params:
- name: source
type: string
description: dynamic | user | factory; memory index examples D1, U1, F1; complete ranges UNRESOLVED
- name: emulated
type: string
description: E1 | E2 for FP-UMX-TPS-TX120 series (§11.7.6)
- id: lw3_switch_all_edids
label: Emulate EDID on All Input Ports (LW3)
kind: action
command: "CALL·/EDID:switchAll(<dynamic|user|factory>)"
params:
- name: source
type: string
description: dynamic | user | factory; memory index examples D1, U1, F1; complete ranges UNRESOLVED
- id: lw3_copy_edid
label: Copy EDID to User Memory (LW3)
kind: action
command: "CALL·/EDID:copy(<dynamic|emulated|factory|user>:<user>)"
params:
- name: source
type: string
description: dynamic | emulated | factory | user; memory index examples D1, E1, F1, U1; complete ranges UNRESOLVED
- name: user
type: string
description: User EDID memory index; example U1; range UNRESOLVED
- id: lw3_delete_user_edid
label: Delete EDID From User Memory (LW3)
kind: action
command: "CALL·/EDID:delete(<user>)"
params:
- name: user
type: string
description: User EDID memory index; example U1; range UNRESOLVED
- id: lw3_reset_edids
label: Reset Emulated EDIDs (LW3)
kind: action
command: "CALL /EDID:reset()"
params: []
# Host application commands from §5.2 and §8.6; these are not device wire commands.
# Host execution transport is UNRESOLVED in the Transport schema above.
- id: ldc_connect_ip
label: Connect LDC by IP Address
kind: action
command: "LightwareDeviceController -i <IP_address>:<port>"
params:
- name: ip_address
type: string
description: Static IP address; range UNRESOLVED
- name: port
type: string
description: If not set, default 10001 (LW2 protocol); LW3 uses 6107; other accepted values UNRESOLVED
- id: ldc_connect_serial
label: Connect LDC by Serial Port
kind: action
command: "LightwareDeviceController -c <COM_port>:<Baud>"
params:
- name: com_port
type: string
description: Serial port; range UNRESOLVED
- name: baud
type: string
description: If not set, detected automatically; command-specific range UNRESOLVED
- id: ldc_set_zoom
label: Set LDC Zoom
kind: action
command: "LightwareDeviceController -z <magnifying_value>"
params:
- name: magnifying_value
type: string
description: Default 1 (100%); range UNRESOLVED; last value stored for subsequent starts
- id: ldu2_help
label: List LDU2 CLI Commands
kind: query
command: "LightwareDeviceUpdaterV2_CLI.cmd help"
params: []
- id: ldu2_version
label: Query LDU2 and Script API Versions
kind: query
command: "LightwareDeviceUpdaterV2_CLI.cmd version"
params: []
- id: ldu2_check_for_updates
label: Check for New LDU2 Version
kind: query
command: "LightwareDeviceUpdaterV2_CLI.cmd checkForUpdates"
params: []
- id: ldu2_device_info
label: Query Device Information With LDU2
kind: query
command: "LightwareDeviceUpdaterV2_CLI.cmd deviceInfo [options]"
params:
- name: ip
type: string
description: -i or --ip; List of IP addresses; one of ip or hostName mandatory; list syntax UNRESOLVED
- name: host_name
type: string
description: -n or --hostName; List of hostnames; one of ip or hostName mandatory; list syntax UNRESOLVED
- name: package_version
type: string
description: -v or --packageVersion; optional flag; shows installed package version only
- id: ldu2_update
label: Update Device Firmware With LDU2
kind: action
command: "LightwareDeviceUpdaterV2_CLI.cmd update [options]"
params:
- name: package
type: string
description: -p or --package; firmware package file path; required
- name: ip
type: string
description: -i or --ip; List of IP addresses; one of ip or hostName mandatory; list syntax UNRESOLVED
- name: host_name
type: string
description: -n or --hostName; List of hostnames; one of ip or hostName mandatory; list syntax UNRESOLVED
- name: backup_folder
type: string
description: -b or --backupFolder; optional; default USER_HOME/.ldu2/backup
- name: factory_default
type: string
description: -f or --factoryDefault; optional flag; Default false
- name: report_progress
type: string
description: -r or --reportProgress; optional flag; Default false
- name: skip_presets_at_restore
type: string
description: --skipPresetsAtRestore; package-specific; if true, device presets will not be restored; Default false
- name: upload_default_mini_web
type: string
description: --uploadDefaultMiniWeb; package-specific; if true and no custom miniweb is present, uploads default built-in miniweb; Default false
- name: clear_text_login_pw
type: string
description: --clearTextLoginPw; package-specific; cleartext login password; Default empty string; length UNRESOLVED
- name: test
type: string
description: --test; package-specific; if true, no update performed and device communication tested; Default false
- id: ldu2_restore
label: Restore Device Configuration With LDU2
kind: action
command: "LightwareDeviceUpdaterV2_CLI.cmd restore [options]"
params:
- name: ip
type: string
description: -i or --ip; List of IP addresses; one of ip or hostName mandatory; list syntax UNRESOLVED
- name: host_name
type: string
description: -n or --hostName; List of hostnames; one of ip or hostName mandatory; list syntax UNRESOLVED
- name: backup_file
type: string
description: -b or --backupFile; configuration backup file path; required
- name: keep_original_ip
type: string
description: -k or --keepOriginalIp; optional flag; preserves device network settings instead of overriding from backup; Default false
- id: ldu2_package_options
label: Query LDU2 Package Options
kind: query
command: "LightwareDeviceUpdaterV2_CLI.cmd packageOptions [options]"
params:
- name: package
type: string
description: -p or --package; firmware package file path; required
Feedbacks
- id: lcmd_response
type: string
description: Multi-line listing of all LW2 commands, terminated with `(LCMD END)CrLf`
query_command: "{lcmd}"
- id: product_type
type: string
description: "(I:<PRODUCT_TYPE>)CrLf"
query_command: "{i}"
- id: device_label
type: string
description: "(LABEL=<device_label>)CrLf"
query_command: "{label}"
- id: current_protocol
type: string
description: "(CURRENT PROTOCOL = #1) - '#1' = LW2"
query_command: "{P_?}"
- id: firmware_version
type: string
description: "(FW:<FW_VER><s>)CrLf - e.g. (FW:1.6.0b13 r99)"
query_command: "{F}"
- id: pong
type: string
description: "(PONG!)CrLf"
query_command: "{PING}"
- id: compiled_date
type: string
description: "(Compiled: <DATE&TIME>)CrLf"
query_command: "{CT}"
- id: serial_number
type: string
description: "(SN:<SERIAL_N>)CrLf - 8-digit serial"
query_command: "{S}"
- id: installed_boards
type: string
description: "(SL# 0 <MB_DESC>)CrLf" followed by `(SL END)`
query_command: "{IS}"
- id: firmware_controllers
type: string
description: "(CF <DESC>)CrLf" lines terminated with `(CF END)CrLf`
query_command: "{FC}"
- id: health_status
type: string
description: "(ST CPU 12.16V 5.03V 3.30V 3.33V 3.37V 1.30V 1.86V 1.00V 53.22C 53.26C)"
query_command: "{ST}"
- id: switch_ack
type: string
description: "(O<out2> I<in2> <layer>)CrLf"
- id: mute_ack
type: string
description: "(1MT<out2> <layer>)CrLf - 1 = muted"
- id: unmute_ack
type: string
description: "(0MT<out2> <layer>)CrLf - 0 = unmuted"
- id: lock_ack
type: string
description: "(1LO<out²> <layer>)CrLf - 1 = locked"
- id: unlock_ack
type: string
description: "(0LO<out2> <layer>)CrLf - 0 = unlocked"
- id: crosspoint_state
type: string
description: "(ALL<layer> <O01> <O02>…)CrLf - state letters L=locked, M=muted, U=locked+muted"
query_command: "{VC·<layer>}"
- id: crosspoint_size
type: string
description: "(SIZE=<size> <layer>)CrLf - e.g. (SIZE=6x1 V)"
query_command: "{getsize·<layer>}"
- id: ip_status
type: string
description: "(IP_STAT=<type>;<ip_address>;<subnet_mask>;<gateway_addr>)CrLf"
query_command: "{IP_STAT=?}"
- id: gpio_ack
type: string
description: "(GPIO<pin_nr>=<dir>;<level>)CrLf"
query_command: "{GPIO<pin_nr>=?}"
- id: lw3_property_response
type: string
description: LW3 GET response - e.g. `pr /.ProductName=UMX-TPS-TX140-Plus`
query_command: "GET /.ProductName"
Variables
# Source documents settable variables; full LW3 path/property list not enumerated in the excerpt.
# UNRESOLVED: source §7.10 Variable-Management detail not in excerpt; refer to LW3 programmer's reference.
Events
# Source documents LW3 subscription notifications.
- id: lw3_chg_notification
type: string
description: "Change message format: `CHG /<node_path>=<value>` - emitted asynchronously when subscribed property changes."
Macros
# Per source §5.10.6 (only on UMX-TPS-TX140K and TX140-Plus from FW v1.5.0b4; FP/WP-UMX-TPS series from v1.5.0b6).
- id: macro_file_format
type: string
description: |
LW3 macros stored as plain-text files with extension `.LW3`:
```
;<preset_name>
;Begin <macro1_name>
<LW3_commands>
;End <macro1_name>
```
Each macro is a sequence of LW3 SET and CALL commands. Syntax not checked at upload time.
Safety
confirmation_required_for:
- factory_reset # UNRESOLVED: explicit confirmation text not quoted in source, but "Load factory defaults" prompts per source §5.11.4
- reboot # UNRESOLVED: no explicit confirmation prompt documented for {RST} in source
interlocks: []
# UNRESOLVED: source mentions "Cleartext Login" protection (§5.12.5) and "Lock front panel" (§5.12.3) but no interlock procedure spec.
Notes
- LW2 protocol: ASCII commands wrapped in
{ }, terminated with CrLf (\r\n,0x0D 0x0A). All commands converted to uppercase on receive. Responses wrapped in( ). - LW2 over TCP: port
10001. LW3 over TCP: port6107. Default device IP:192.168.0.100. - LW3 protocol: ASCII, CrLf-terminated, case-sensitive tree (
/MEDIA/VIDEO/XP:switch(I1:O1)). Maximum line length 800 bytes. Commands prefixed withGET,SET,CALL,MAN,OPEN,CLOSE,GETALL. Responses prefixed with 2-char code (pr,pw,mO,mF,o-,c-,CHG, etc.). - RS-232 port settings (per source §5.10.1): Baud 4800/7200/9600/14400/19200/38400/57600/115200; Data 8 or 9; Parity None/Odd/Even; Stop 1/1.5/2. RS-232 modes:
CONTROL,CI(Command Injection),PASS(Event Manager pass-through). - Two RS-232 ports: Local and TPS link. RS-232 operation mode mirrors between them; other settings can differ per port.
- Cleartext login (LW3) is optional on TX140K/TX140-Plus and WP-UMX-TX130-Plus-US from FW v1.5.0b4/v1.5.0b6. When enabled, login must be the first command on TCP connections.
- Escape character in LW3 is
\. Control characters to escape:\ { } # % ( ) \r \n \t. - Signature feature: optional 4-hex-digit prefix per command (e.g.
1700#GET /EDID.*) groups a response between{and}brackets. - The
0D0A(CrLf) is the default delimiter for the RS-232 Message Recognizer (§5.10.2) and matches the LW3 command terminator. - GPIO port: 7 pins at TTL digital levels; pin direction (Input/Output) configurable. Only
UMX-TPS-TX130, -TX140, TX140K, TX140-Plusmodels per source §6.7.
Provenance
source_domains:
- go.lightware.com
- academy.lightware.com
source_urls:
- https://go.lightware.com/umx-tps-tx100-s-pum
- https://academy.lightware.com/
retrieved_at: 2026-08-11T07:54:49.108Z
last_checked_at: 2026-10-07T22:11:09.783Z
Verification Summary
verdict: verified
checked_at: 2026-10-07T22:11:09.783Z
matched_actions: 234
action_count: 234
confidence: medium
summary: "All 234 action units map to literal source commands and the port 10001 claim is supported. Many LW3 features are marked in the source as TX140K/Plus-only, so applicability to the TX120-GES4 is a caveat. (20 unresolved item(s) noted in Known Gaps.)"
Known Gaps
- "CALL·/MEDIA/AUDIO/XP:setAutoselectionPriority"
- "<IP_address>/protocol.lw3"
- "firmware version compatibility not stated in source"
- "no default stated; selectable 4800, 7200, 9600, 14400, 19200, 38400, 57600, 115200"
- "no default stated; selectable 8 or 9"
- "no default stated; selectable None (N), Odd (O), Even (E)"
- "no default stated; selectable 1, 1.5, 2"
- "flow control not stated in source"
- "LW3 uses TCP port 6107 (per source §7.2); not enumerated above since protocols.port holds one value. See Notes."
- "source repeats B2\""
- "source table conflicts with example false\""
- "§7.7.8 has a malformed audio priority command template and a video-path example."
- "source example sets true, while the summary specifies ConditionEndCheck for this delay type\""
- "§7.12.5 uses ApplySettings, while §7.12.1–7.12.4 use applySettings."
- "source length wording is inconsistent\""
- "§7.23 says GPIO port number 1..8, conflicting with the seven-pin descriptions."
- "per source §7 the LW3 protocol tree includes MANY additional sub-systems (Video Port Settings, Audio Port Settings, Analog Audio Input Level Settings, Event Manager, Variable Management, Ethernet Port Config, Ethernet Tool Kit, Ethernet Message Sending, HTTP Messaging, TCP Message Recognizer, RS-232 Port Config, RS-232 Message Sending, RS-232 Message Recognizer, Sending CEC Commands, Infrared Port Config, Infrared Message Sending, GPIO Port Config, EDID Management). The refined source excerpt does not enumerate every node/property/method detail; only the protocol structure and example commands are documented. Implementer should consult the LW3 programmer's reference §7 for full coverage."
- "source §7.10 Variable-Management detail not in excerpt; refer to LW3 programmer's reference."
- "FP-UMX-TPS-TX120-GES4 macro availability depends on exact firmware/model variant; this is a Plus-tier feature."
- "explicit confirmation text not quoted in source, but \"Load factory defaults\" prompts per source §5.11.4"
- "no explicit confirmation prompt documented for {RST} in source"
- "source mentions \"Cleartext Login\" protection (§5.12.5) and \"Lock front panel\" (§5.12.3) but no interlock procedure spec."
From the AI4AV catalog (https://ai4av.net) · ODbL-1.0