AI4AVSummary
The Extron DMP 128 Plus is an 8x8 Digital Matrix Processor (audio DSP mixer) with mic/line inputs, aux inputs, virtual returns, and Dante (AT models) / expansion bus audio networking, plus VoIP telephony (V models) and file/tone playback. Control is via Extron's Simple Instruction Set (SIS) over rear-panel RS-232 (38400 baud), front-panel USB, or Ethernet (Telnet on port 23, web on port 80). SIS covers IP/NTP configuration, password security, file handling, preset recall, audio gain/mute control, mix-point routing, group masters, macros, signal level monitoring, automixer gate monitoring, VoIP call control, and Dante passthrough to remote AXI/NetPA devices.
Transport
# Source: DMP 128 Plus User Guide, 68-2826-01, Rev. M, pp.6, 28-30.
# RS-232: "38400 baud, No parity, 1 stop bit, 8 data bits, No flow control" (verbatim, p.28).
# TCP: "Communications ... is via Telnet, using port 23" (verbatim, p.28).
# Web: "Port 80 is the default port for web browsers" (verbatim, p.31).
# Auth: Optional admin/user password (IP connections only). Factory password = device serial #.
# "Passwords only apply to IP connections and can be up to 128 characters in length." (verbatim, p.30)
# "Connection via RS-232" default verbose mode is 1 (never password-prompted).
protocols:
- tcp
- serial
- http
addressing:
port: 23 # Telnet default (TCP). Web browser default port 80 also stated.
serial:
baud_rate: 38400
data_bits: 8
parity: none
stop_bits: 1
flow_control: none
auth:
type: password # optional; applies to IP connections only
notes: |
Optional admin/user password. Factory password is the device serial number;
case-sensitive, up to 128 chars. RS-232/USB connections are never
password-protected. Telnet/Web connections are password-protected only if a
password has been set; default after factory reset is no password.
Traits
# - queryable (many query commands: I, 1I..4I, Q, *Q, **Q, X2*Q, N, E CI }, E CS },
# E CG }, E DH }, E CV }, E CT }, E CN }, E CP }, E CF }, E CA },
# E CU }, E CK }, E CC }, read gain/mute, view group fader, macro status, etc.)
# - levelable (audio gain/trim/attenuation/group fader, 0.1 dB increments via 10x multiplier)
# - routable (mix-point mute/unmute = signal routing between input and output OIDs)
# - macroable (macros 1-64, run/kill/status/name/power-on)
traits:
- queryable
- levelable
- routable
- macroable
Actions
# All ASCII command strings copied verbatim from source Command and Response
# tables (DMP 128 Plus User Guide pp.38-53). Notation:
# ] = CR/LF terminator (device->host)
# } = soft carriage return (no line feed) terminator inside SIS commands
# E = Escape character (Hex 1B) command prefix
# • = space character (only where source marks it with bullet)
# * = asterisk (command character, not a variable)
# Xn# = source-defined variable (see symbol key pp.32-37; params on each action)
# . = period command character (recall preset)
# Mix-point OID tables (pp.59-65) and the OID tables (pp.55-58) are parameter
# value spaces for the G/M opcodes below, NOT separate commands.
# ---------- Information Requests ----------
- id: query_general_information
label: General Information
kind: query
command: "I"
params: []
notes: "Response: VnnXnn•A12x08•E16x16]"
- id: view_model_name
label: Model Name
kind: query
command: "1I"
params: []
notes: "Response: DMP 128 Plus] (model varies)."
- id: view_model_description
label: Model Description
kind: query
command: "2I"
params: []
notes: "Response: Digital audio matrix processor]"
- id: view_system_memory_usage
label: System Memory Usage
kind: query
command: "3I"
params: []
notes: "Response: <number> Bytes Used out of <number> KBytes]"
- id: view_user_memory_usage
label: User Memory Usage
kind: query
command: "4I"
params: []
notes: "Response: <number> Bytes Used out of <number> KBytes]"
- id: query_firmware_version
label: Firmware Version
kind: query
command: "Q"
params: []
notes: "Response: {version x.xx}]"
- id: query_firmware_version_with_build
label: Firmware Version With Build
kind: query
command: "*Q"
params: []
notes: "Response: {version x.xx.xxxx}]"
- id: query_kernel_library_version
label: Kernel/Library Version
kind: query
command: "**Q"
params: []
notes: "Response: {version x.xx.xxxx LX}]"
- id: query_firmware_version_advanced
label: Firmware Version (Advanced)
kind: query
command: "X2*Q"
params:
- name: query_type
source_symbol: X2*
type: integer
description: "0=Detailed version info (all 2Q/3Q/4Q); 1=Firmware version; 2=Final stage bootloader; 3=Factory base code version; 4=Updated firmware version."
notes: "Response: {specific version info}]"
- id: view_part_number
label: Part Number
kind: query
command: "N"
params: []
notes: "Response: zz-zzzz-zz]"
# ---------- Ethernet Data Port ----------
- id: set_current_connected_port_timeout
label: Set Current Connected Port Timeout
kind: action
command: "E 0* X2# TC }"
params:
- name: timeout
source_symbol: X2#
type: integer
description: "1 to 65000, 1 step = 10 seconds, default = 30 (300 seconds)."
- id: view_current_connected_port_timeout
label: View Current Connected Port Timeout
kind: query
command: "E 0TC }"
params: []
- id: set_global_ip_port_timeout
label: Set Global IP Port Timeout
kind: action
command: "E 1* X2# TC }"
params:
- name: timeout
source_symbol: X2#
type: integer
description: "1 to 65000, 1 step = 10 seconds, default = 30 (300 seconds)."
- id: view_global_ip_port_timeout
label: View Global IP Port Timeout
kind: query
command: "E 1TC }"
params: []
# ---------- Serial Data Port ----------
- id: configure_serial_parameters
label: Configure Serial Parameters
kind: action
command: "E X! * X1) , X1! , X1@ , X2% CP }"
params:
- name: port_number
source_symbol: X!
type: integer
description: "01 (always 01 for DMP 128 Plus)."
- name: baud_rate
source_symbol: X1)
type: integer
description: "300,600,1200,1800,2400,3600,4800,7200,9600,14400,19200,28800,38400 (default),57600,115200."
- name: parity
source_symbol: X1!
type: string
description: "O=odd, E=even, N=none (default), S=space, M=mark. Only first letter needed."
- name: data_bits
source_symbol: X1@
type: integer
description: "7 or 8 (default 8)."
- name: stop_bits
source_symbol: X2%
type: integer
description: "1 or 2 (default 1)."
- id: view_serial_parameters
label: View Serial Parameters
kind: query
command: "E X! CP }"
params:
- name: port_number
source_symbol: X!
type: integer
- id: view_serial_port_mode
label: View Serial Port Mode
kind: query
command: "E X! CY }"
params:
- name: port_number
source_symbol: X!
type: integer
notes: "Response: X1# = 0 (RS-232 default)."
- id: configure_flow_control
label: Configure Flow Control
kind: action
command: "E X! * X1$ , X1% CF }"
params:
- name: port_number
source_symbol: X!
type: integer
- name: flow_control
source_symbol: X1$
type: string
description: "H=hardware, S=software, N=none (default). Only first letter needed."
- name: data_pacing
source_symbol: X1%
type: integer
description: "Milliseconds between bytes, 0000-1000 ms (default 0). Ignored for host ports."
- id: view_flow_control
label: View Flow Control
kind: query
command: "E X! CF }"
params:
- name: port_number
source_symbol: X!
type: integer
# ---------- IP Setup Commands ----------
- id: set_unit_name
label: Set Unit Name
kind: action
command: "E X# CN }"
params:
- name: name
source_symbol: X#
type: string
description: "Up to 63 chars, A-Z, 0-9, and hyphen (-)."
- id: set_unit_name_to_factory_default
label: Set Unit Name to Factory Default
kind: action
command: "E • CN }"
params: []
notes: "Sets to default name = model name + last 3 pairs of MAC address."
- id: view_unit_name
label: View Unit Name
kind: query
command: "E CN }"
params: []
- id: set_date_time
label: Set Date and Time
kind: action
command: "E X$ CT }"
params:
- name: datetime
source_symbol: X$
type: string
description: "MM/DD/YY-HH:MM:SS"
- id: view_date_time
label: View Date and Time
kind: query
command: "E CT }"
params: []
- id: view_date_time_in_hex
label: View Date and Time in Hex
kind: query
command: "E *CT }"
params: []
notes: "Response: X2@ (7 hex bytes: month, day, year, hour, min, sec, day-of-week)."
- id: view_gmt_offset
label: View GMT Offset
kind: query
command: "E CZ }"
params: []
notes: "Response: X@ (hh:mm offset from GMT)."
- id: set_dhcp_on
label: Set DHCP On
kind: action
command: "E 1DH }"
params: []
- id: set_dhcp_off
label: Set DHCP Off
kind: action
command: "E 0DH }"
params: []
- id: view_dhcp_mode
label: View DHCP Mode
kind: query
command: "E DH }"
params: []
notes: "Response: X3$ = 0 (off/default) or 1 (on)."
- id: set_ip_address
label: Set IP Address
kind: action
command: "E X% CI }"
params:
- name: ip
source_symbol: X%
type: string
description: "xxx.xxx.xxx.xxx. Default 192.168.254.254."
- id: view_ip_address
label: View IP Address
kind: query
command: "E CI }"
params: []
- id: view_hardware_address_mac
label: View Hardware Address (MAC)
kind: query
command: "E CH }"
params: []
notes: "Verbose mode 2/3 only. Response: X^ = 00-05-A6-xx-xx-xx."
- id: set_subnet_mask
label: Set Subnet Mask
kind: action
command: "E X& CS }"
params:
- name: mask
source_symbol: X&
type: string
description: "xxx.xxx.xxx.xxx. Default 255.255.255.0."
- id: view_subnet_mask
label: View Subnet Mask
kind: query
command: "E CS }"
params: []
- id: set_gateway_ip_address
label: Set Gateway IP Address
kind: action
command: "E X% CG }"
params:
- name: gateway
source_symbol: X%
type: string
- id: set_ip_only
label: Set IP (IP Only)
kind: action
command: "E X2( * X% CISG }"
params:
- name: nic_number
source_symbol: X2(
type: integer
description: "1=LAN 1, 2=LAN 2 (V models only)."
- name: ip
source_symbol: X%
type: string
notes: "First X% = IP address; X2( = NIC."
- id: set_ip_subnet
label: Set IP/Subnet
kind: action
command: "E X2( * X% / X3) CISG }"
params:
- name: nic_number
source_symbol: X2(
type: integer
- name: ip
source_symbol: X%
type: string
- name: prefix
source_symbol: X3)
type: string
description: "Subnet mask bits, e.g. /16 = 255.255.0.0."
- id: set_ip_subnet_gateway
label: Set IP/Subnet/Gateway
kind: action
command: "E X2( * X% / X3) * X% CISG }"
params:
- name: nic_number
source_symbol: X2(
type: integer
- name: ip
source_symbol: X%
type: string
- name: prefix
source_symbol: X3)
type: string
- name: gateway
source_symbol: X%
type: string
notes: "In all CISG commands, first X% = IP, X3) = subnet, second X% = gateway."
- id: view_ip_subnet_gateway
label: View IP/Subnet/Gateway
kind: query
command: "E X2( CISG }"
params:
- name: nic_number
source_symbol: X2(
type: integer
- id: set_dns_server_ip
label: Set DNS Server IP Address
kind: action
command: "E X% DI }"
params:
- name: dns
source_symbol: X%
type: string
- id: view_dns_server_ip
label: View DNS Server IP Address
kind: query
command: "E DI }"
params: []
- id: set_verbose_mode
label: Set Verbose Mode
kind: action
command: "E X( CV }"
params:
- name: mode
source_symbol: X(
type: integer
description: "0=Clear/none (default for Telnet); 1=Verbose (default for USB/RS-232); 2=Tagged responses; 3=Verbose + tagged responses."
- id: view_verbose_mode
label: View Verbose Mode
kind: query
command: "E CV }"
params: []
- id: get_connection_count
label: Get Connection Count
kind: query
command: "E CC }"
params: []
notes: "Response: {number of connections}]"
# ---------- Password and Security Settings ----------
- id: set_admin_password
label: Set Admin Password
kind: action
command: "E X1^ CA }"
params:
- name: password
source_symbol: X1^
type: string
description: "0-128 chars, all human-readable except |. Cannot be a single space. Case-sensitive."
- id: clear_admin_password
label: Clear Admin Password
kind: action
command: "E • CA }"
params: []
- id: view_admin_password
label: View Admin Password
kind: query
command: "E CA }"
params: []
notes: "Response: X1& = **** if password exists, empty if not."
- id: set_user_password
label: Set User Password
kind: action
command: "E X1^ CU }"
params:
- name: password
source_symbol: X1^
type: string
- id: clear_user_password
label: Clear User Password
kind: action
command: "E • CU }"
params: []
- id: view_user_password
label: View User Password
kind: query
command: "E CU }"
params: []
- id: view_session_security_level
label: View Session Security Level
kind: query
command: "E CK }"
params: []
notes: "Response: X2) = 11 (User) or 12 (Administrator)."
# ---------- Directories ----------
- id: change_create_directory
label: Change/Create Directory
kind: action
command: "E path/directory/CJ }"
params:
- name: path
type: string
description: "Directory path."
notes: "Response: Dir•path/directory/]"
- id: back_to_root_directory
label: Back to Root Directory
kind: action
command: "E / CJ }"
params: []
- id: up_one_directory
label: Up One Directory
kind: action
command: "E .. CJ }"
params: []
- id: view_current_directory
label: View Current Directory
kind: query
command: "E CJ }"
params: []
# ---------- File Commands ----------
- id: erase_current_directory_files
label: Erase Current Directory and Files
kind: action
command: "E / EF }"
params: []
notes: "Response: Ddl]"
- id: erase_current_directory_subdirs
label: Erase Current Directory and Subdirectories
kind: action
command: "E // EF }"
params: []
- id: list_files_current_directory
label: List Files From Current Directory
kind: query
command: "E DF }"
params: []
notes: "Response: filenamex• date/time • length] (one per file)."
- id: list_files_current_directory_and_below
label: List Files From Current Directory and Below
kind: query
command: "E LF }"
params: []
- id: load_file_to_user_flash
label: Load File to User Flash Memory
kind: action
command: "E +UF filesize , filename }"
params:
- name: filesize
type: integer
- name: filename
type: string
notes: "Response: Upl]"
- id: retrieve_file_from_user_flash
label: Retrieve File From User Flash Memory
kind: action
command: "E filename SF }"
params:
- name: filename
type: string
notes: "Responds with 4 bytes of file size and unprocessed file data."
# ---------- Backup / Restore Device Configuration ----------
- id: save_device_configuration
label: Save Device Configuration
kind: action
command: "E 1* X2& XF }"
params:
- name: config_type
source_symbol: X2&
type: integer
description: "0=IP configuration, 2=Device-specific parameters."
notes: "Response: Cnfg1* X2&]"
# ---------- NTP (Network Time Protocol) ----------
- id: enable_ntp
label: Enable NTP
kind: action
command: "E 1 NTEN }"
params: []
notes: "Response: Nten1]"
- id: disable_ntp
label: Disable NTP
kind: action
command: "E 0 NTEN }"
params: []
notes: "Response: Nten0]"
- id: sync_ntp_now
label: Sync NTP Now
kind: action
command: "E 2 NTEN }"
params: []
notes: "Response: Nten2]"
- id: view_ntp_status
label: View NTP Status
kind: query
command: "E NTEN }"
params: []
notes: "Response: X2^ = 0 (disabled/default) or 1 (enabled)."
- id: set_ntp_ip_address
label: Set NTP IP Address
kind: action
command: "E X% NTIP }"
params:
- name: ntp_ip
source_symbol: X%
type: string
notes: "Response: Ntip X%]"
- id: set_multiple_ntp_ip_addresses
label: Set Multiple NTP IP Addresses
kind: action
command: "E X% * ... X% NTIP }"
params:
- name: ntp_ips
source_symbol: X%
type: string
description: "Up to 4 NTP addresses separated by *. Can be URL or IP."
notes: "Response: Ntip X% * ... X%]"
- id: clear_ntp_ip_address
label: Clear NTP IP Address
kind: action
command: "E • NTIP }"
params: []
notes: "Response: Ntip]"
- id: view_ntp_ip_address
label: View NTP IP Address
kind: query
command: "E NTIP }"
params: []
notes: "Response: X% * ... X%]"
# ---------- Port Assignment (LAN 1 legacy + per-NIC PMAP) ----------
- id: set_telnet_port_map_lan1
label: Set Telnet Port Map (LAN 1)
kind: action
command: "E X5& MT }"
params:
- name: port
source_symbol: X5&
type: integer
description: "0=Off, custom ports must be 1024 or higher."
notes: "LAN 1 only. Response: Pmt X5&]"
- id: reset_telnet_port_map_lan1
label: Reset Telnet Port Map (LAN 1)
kind: action
command: "E 23 MT }"
params: []
notes: "LAN 1 only. Response: Pmt00023]"
- id: disable_telnet_port_lan1
label: Disable Telnet Port (LAN 1)
kind: action
command: "E 0 MT }"
params: []
notes: "LAN 1 only. Response: Pmt00000]"
- id: view_telnet_port_map_lan1
label: View Telnet Port Map (LAN 1)
kind: query
command: "E MT }"
params: []
notes: "LAN 1 only."
- id: set_web_port_map_lan1
label: Set Web Port Map (LAN 1)
kind: action
command: "E X5& MH }"
params:
- name: port
source_symbol: X5&
type: integer
- id: reset_web_port_map_lan1
label: Reset Web Port Map (LAN 1)
kind: action
command: "E 80 MH }"
params: []
notes: "Response: Pmt00080]"
- id: disable_web_port_lan1
label: Disable Web Port (LAN 1)
kind: action
command: "E 0 MH }"
params: []
- id: view_web_port_map_lan1
label: View Web Port Map (LAN 1)
kind: query
command: "E MH }"
params: []
- id: set_telnet_port_map_per_nic
label: Set Telnet Port Map (Per NIC)
kind: action
command: "E Z X5$ * X5& PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
description: "1=LAN 1, 2=LAN 2."
- name: port
source_symbol: X5&
type: integer
notes: "Response: Pmap Z• X5$ * X5&]"
- id: reset_telnet_port_map_per_nic
label: Reset Telnet Port Map (Per NIC)
kind: action
command: "E Z X5$ * 23 PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
notes: "Reset port to default 23. Response: Pmap Z• X5$ * 00023]"
- id: disable_telnet_port_per_nic
label: Disable Telnet Port (Per NIC)
kind: action
command: "E Z X5$ * 0 PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- id: view_telnet_port_map_per_nic
label: View Telnet Port Map (Per NIC)
kind: query
command: "E Z X5$ PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- id: set_web_port_map_per_nic
label: Set Web Port Map (Per NIC)
kind: action
command: "E W X5$ * X5& PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- name: port
source_symbol: X5&
type: integer
- id: reset_web_port_map_per_nic
label: Reset Web Port Map (Per NIC)
kind: action
command: "E W X5$ * 80 PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
notes: "Reset to default 80."
- id: disable_web_port_per_nic
label: Disable Web Port (Per NIC)
kind: action
command: "E W X5$ * 0 PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- id: view_web_port_map_per_nic
label: View Web Port Map (Per NIC)
kind: query
command: "E W X5$ PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- id: set_snmp_port_map
label: Set SNMP Port Map
kind: action
command: "E A X5$ * X5& PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- name: port
source_symbol: X5&
type: integer
- id: reset_snmp_port_map
label: Reset SNMP Port Map
kind: action
command: "E A X5$ * 161 PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
notes: "Reset to default 161."
- id: disable_snmp_port
label: Disable SNMP Port
kind: action
command: "E A X5$ * 0 PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- id: view_snmp_port_map
label: View SNMP Port Map
kind: query
command: "E A X5$ PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- id: set_sis_over_ssh_port_map
label: Set SIS-over-SSH Port Map
kind: action
command: "E B X5$ * X5& PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- name: port
source_symbol: X5&
type: integer
- id: disable_sis_over_ssh_port
label: Disable SIS-over-SSH Port
kind: action
command: "E B X5$ * 0 PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- id: view_sis_over_ssh_port_map
label: View SIS-over-SSH Port Map
kind: query
command: "E B X5$ PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
# UNRESOLVED: the "Reset SIS-over-SSH port map" command was truncated in the
# source excerpt; the default reset value (likely 22) is not shown verbatim.
- id: set_ssl_port_map
label: Set SSL Port Map
kind: action
command: "E S X5$ * X5& PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- name: port
source_symbol: X5&
type: integer
- id: reset_ssl_port_map
label: Reset SSL Port Map
kind: action
command: "E S X5$ * 443 PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
notes: "Reset to default 443."
- id: disable_ssl_port
label: Disable SSL Port
kind: action
command: "E S X5$ * 0 PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
- id: view_ssl_port_map
label: View SSL Port Map
kind: query
command: "E S X5$ PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
# ---------- SNMP (Simple Network Management Protocol) ----------
- id: set_unit_contact
label: Set Unit Contact
kind: action
command: "E C X3! SNMP }"
params:
- name: contact
source_symbol: X3!
type: string
description: "Up to 64 characters."
notes: "Response: SnmpC* X3!]"
- id: set_unit_contact_default
label: Set Unit Contact to Default
kind: action
command: "E C • SNMP }"
params: []
notes: "Response: SnmpC* Not Specified]"
- id: view_unit_contact
label: View Unit Contact
kind: query
command: "E C SNMP }"
params: []
- id: set_unit_location
label: Set Unit Location
kind: action
command: "E L X3! SNMP }"
params:
- name: location
source_symbol: X3!
type: string
- id: set_unit_location_default
label: Set Unit Location to Default
kind: action
command: "E L • SNMP }"
params: []
- id: view_unit_location
label: View Unit Location
kind: query
command: "E L SNMP }"
params: []
- id: set_community_public
label: Set Community Public (Read-Only)
kind: action
command: "E P X3! SNMP }"
params:
- name: community
source_symbol: X3!
type: string
- id: set_community_public_default
label: Set Community Public to Default
kind: action
command: "E P • SNMP }"
params: []
notes: "Response: SnmpP* public]"
- id: view_community_public
label: View Community Public
kind: query
command: "E P SNMP }"
params: []
- id: enable_snmp_access
label: Enable SNMP Access
kind: action
command: "E E1 SNMP }"
params: []
notes: "Response: SnmpE*1]"
- id: disable_snmp_access
label: Disable SNMP Access
kind: action
command: "E E0 SNMP }"
params: []
notes: "Response: SnmpE*0]"
- id: view_snmp_access_setting
label: View SNMP Access Setting
kind: query
command: "E E SNMP }"
params: []
notes: "Response: X5^ = 0 (disabled/default) or 1 (enabled)."
# ---------- Reboot Commands ----------
- id: reboot_system
label: Reboot System
kind: action
command: "E 1 BOOT }"
params: []
notes: "Response: Boot1]"
- id: reboot_network
label: Reboot Network
kind: action
command: "E 2 BOOT }"
params: []
notes: "Response: Boot2]"
# ---------- Ping ----------
- id: execute_ping_test
label: Execute Ping Test
kind: action
command: "E {address} PING }"
params:
- name: address
type: string
description: "IP address or hostname to ping."
notes: "Response: {address}*{bytes}*{ttl}*{time}] or {address}*0*0*0] on failure."
# ---------- Time Zone and Daylight Settings ----------
- id: set_time_zone
label: Set Time Zone
kind: action
command: "E {zone name} * TZON }"
params:
- name: zone_name
type: string
notes: "Response: Tzon• {timezone code, UTC offset and location name}]"
- id: view_current_time_zone
label: View Current Time Zone
kind: query
command: "E TZON }"
params: []
- id: list_all_time_zones
label: List All Time Zones
kind: query
command: "E * TZON }"
params: []
notes: "Response: one line per zone, multiple ]]"
# ---------- Digital I/O ----------
- id: get_digital_input_status
label: Get Digital Input Status
kind: query
command: "E X3# GPIT }"
params:
- name: channel
source_symbol: X3#
type: integer
description: "1 through 8."
notes: "Response: X3% * X3^] (action type * varies)."
- id: get_digital_output_status
label: Get Digital Output Status
kind: query
command: "E X3# * X3& GPOT }"
params:
- name: channel
source_symbol: X3#
type: integer
- name: output
source_symbol: X3&
type: integer
description: "1 or 2."
notes: "Response: X3* * X3(] (output mode * monitor varies)."
- id: get_state_for_input
label: Get State for Input
kind: query
command: "E X3# GPI }"
params:
- name: channel
source_symbol: X3#
type: integer
notes: "Response: Gpi X3# * X3@]. X3@ = 0 (low) or 1 (high)."
# ---------- Write Names ----------
- id: write_input_name
label: Write Input Name
kind: action
command: "E X4! , X4^ NI }"
params:
- name: input_number
source_symbol: X4!
type: integer
description: "1 through 20 (13-20 are Aux inputs)."
- name: name
source_symbol: X4^
type: string
- id: write_virtual_return_name
label: Write Virtual Return Name
kind: action
command: "E X4@ , X4^ NL }"
params:
- name: virtual_return
source_symbol: X4@
type: integer
description: "1 through 16."
- name: name
source_symbol: X4^
type: string
- id: write_exp_input_name
label: Write EXP Input Name
kind: action
command: "E X4# , X4^ NE }"
params:
- name: exp_input
source_symbol: X4#
type: integer
description: "1 through 16 (1 through 48 on AT models)."
- name: name
source_symbol: X4^
type: string
- id: write_output_name
label: Write Output Name
kind: action
command: "E X4$ , X4^ NO }"
params:
- name: output_number
source_symbol: X4$
type: integer
description: "1 through 16 (9-16 are Aux outputs)."
- name: name
source_symbol: X4^
type: string
- id: write_exp_output_name
label: Write EXP Output Name
kind: action
command: "E X4% , X4^ NX }"
params:
- name: exp_output
source_symbol: X4%
type: integer
description: "1 through 16."
- name: name
source_symbol: X4^
type: string
- id: write_preset_name
label: Write Preset Name
kind: action
command: "E X4) , X4^ NG }"
params:
- name: preset_number
source_symbol: X4)
type: integer
description: "1 through 32."
- name: name
source_symbol: X4^
type: string
# ---------- View Names ----------
- id: view_input_name
label: View Input Name
kind: query
command: "E X4! NI }"
params:
- name: input_number
source_symbol: X4!
type: integer
- id: view_virtual_return_name
label: View Virtual Return Name
kind: query
command: "E X4@ NL }"
params:
- name: virtual_return
source_symbol: X4@
type: integer
- id: view_exp_input_name
label: View EXP Input Name
kind: query
command: "E X4# NE }"
params:
- name: exp_input
source_symbol: X4#
type: integer
- id: view_output_name
label: View Output Name
kind: query
command: "E X4$ NO }"
params:
- name: output_number
source_symbol: X4$
type: integer
- id: view_exp_output_name
label: View EXP Output Name
kind: query
command: "E X4% NX }"
params:
- name: exp_output
source_symbol: X4%
type: integer
- id: view_preset_name
label: View Preset Name
kind: query
command: "E X4) NG }"
params:
- name: preset_number
source_symbol: X4)
type: integer
# ---------- Recall Presets ----------
- id: recall_preset
label: Recall Preset
kind: action
command: "X4) ."
params:
- name: preset_number
source_symbol: X4)
type: integer
description: "1 through 32."
notes: "Command character is a period. Response: Rpr X4)]. Example: 5. recalls preset 5."
# ---------- Reset to Factory Default ----------
- id: reset_presets_and_names
label: Reset Presets and Names
kind: action
command: "E ZG }"
params: []
notes: "Response: Zpg]"
- id: reset_individual_preset
label: Reset Individual Preset
kind: action
command: "E X4) ZG }"
params:
- name: preset_number
source_symbol: X4)
type: integer
notes: "Response: Zpg X4)]"
- id: partial_factory_reset
label: Partial Factory Reset
kind: action
command: "E ZXXX }"
params: []
notes: "Response: Zpx]"
- id: reset_flash_file_system
label: Reset Flash File System
kind: action
command: "E ZFFF }"
params: []
notes: "Response: Zpf]"
- id: full_factory_reset
label: Full Factory Reset
kind: action
command: "E ZQQQ }"
params: []
notes: "Response: Zpq]"
- id: reset_all_device_settings_delete_files
label: Reset All Device Settings and Delete Files
kind: action
command: "E ZY }"
params: []
notes: "Response: Zpy]. Excludes IP/subnet/gateway/unit name/DHCP/port mapping to preserve communication."
# ---------- Player File Management ----------
- id: set_player_file_slot
label: Set File to Slot Association
kind: action
command: "E A X4* * X4& CPLY }"
params:
- name: player_id
source_symbol: X4*
type: integer
description: "1 through 8."
- name: filename
source_symbol: X4&
type: string
description: "Valid chars A-Z, a-z, 0-9, _."
notes: "Response: CplyA X4* * X4&]"
- id: clear_player_file_slot
label: Clear File to Slot Association
kind: action
command: "E A X4* * • CPLY }"
params:
- name: player_id
source_symbol: X4*
type: integer
- id: view_player_file_slot
label: View File to Slot Association
kind: query
command: "E A X4* CPLY }"
params:
- name: player_id
source_symbol: X4*
type: integer
# ---------- Player Commands ----------
- id: start_player_playback
label: Start Playback on Player
kind: action
command: "E X4* * 1 PLAY }"
params:
- name: player_id
source_symbol: X4*
type: integer
notes: "Response: Play X4* *1]"
- id: stop_player_playback
label: Stop Playback on Player
kind: action
command: "E X4* * 0 PLAY }"
params:
- name: player_id
source_symbol: X4*
type: integer
notes: "Response: Play X4* *0]"
- id: player_status
label: Player Status
kind: query
command: "E X4* PLAY }"
params:
- name: player_id
source_symbol: X4*
type: integer
notes: "Response: X5) = 0 (stopped) or 1 (playing)."
- id: set_player_repeat
label: Set Player Repeat
kind: action
command: "E M X4* * X4( CPLY }"
params:
- name: player_id
source_symbol: X4*
type: integer
- name: repeat
source_symbol: X4(
type: integer
description: "0 = play once, 1 = repeat."
notes: "Turning off repeat during playback stops after current iteration."
- id: get_player_repeat_status
label: Get Player Repeat Status
kind: query
command: "E M X4* CPLY }"
params:
- name: player_id
source_symbol: X4*
type: integer
# ---------- Macro Commands ----------
- id: run_macro
label: Run Macro
kind: action
command: "E R X5! MCRO }"
params:
- name: macro_number
source_symbol: X5!
type: integer
description: "1 through 64. Response padded with leading 0."
notes: "Response: McroR X5!]"
- id: kill_macro
label: Kill Macro
kind: action
command: "E K X5! MCRO }"
params:
- name: macro_number
source_symbol: X5!
type: integer
notes: "Response: McroK X5!]"
- id: get_macro_status
label: Get Macro Status
kind: query
command: "E S X5! MCRO }"
params:
- name: macro_number
source_symbol: X5!
type: integer
notes: "Response: X5@ = 0 (idle) or 1-32 (step)."
- id: set_macro_name
label: Set Macro Name
kind: action
command: "E A X5! * X5# MCRO }"
params:
- name: macro_number
source_symbol: X5!
type: integer
- name: name
source_symbol: X5#
type: string
description: "Up to 24 chars, A-Z, a-z, 0-9, _."
notes: "Response: McroA X5! * X5#]"
- id: get_macro_name
label: Get Macro Name
kind: query
command: "E A X5! MCRO }"
params:
- name: macro_number
source_symbol: X5!
type: integer
- id: set_power_on_macro
label: Set Power-On Macro
kind: action
command: "E P X5! MCRO }"
params:
- name: macro_number
source_symbol: X5!
type: integer
description: "0 clears the power-on macro assignment."
notes: "Response: McroP X5!]"
- id: get_power_on_macro
label: Get Power-On Macro
kind: query
command: "E P MCRO }"
params: []
# ---------- Dante Control and Configuration ----------
- id: query_available_remote_devices
label: Query Available Remote Devices
kind: query
command: "E A EXPR }"
params: []
notes: "Returns list of Dante devices connected to the DMP. Verbose 2/3: ExprA• X*]... Requires Verbose mode 1/3."
- id: enable_remote_connection_listening
label: Enable Remote Connection for Listening
kind: action
command: "E C X* * X2$ EXPR }"
params:
- name: dante_device_name
source_symbol: X*
type: string
description: "Device names are not case sensitive."
- name: remote_mode
source_symbol: X2$
type: integer
description: "0 = disabled, 1 = enabled."
notes: "All listening disabled when DMP Dante module rebooted."
- id: read_remote_connection_listening
label: Read Remote Connection Listening Status
kind: query
command: "E C X* EXPR }"
params:
- name: dante_device_name
source_symbol: X*
type: string
- id: query_remote_devices_listened
label: Query Remote Devices Being Listened To
kind: query
command: "E L EXPR }"
params: []
- id: send_command_to_remote_device
label: Send Command to Remote Device
kind: action
command: "{dante@ X* : X5* }"
params:
- name: dante_device_name
source_symbol: X*
type: string
- name: sis_command
source_symbol: X5*
type: string
description: "SIS command to send. Use w for Esc and | for CR."
notes: "Verbose 2/3: {dante@ X* } X5(] (response tagged by DMP). Requires closing bracket }."
# ---------- USB Call Status ----------
- id: view_usb_call_status
label: View USB 1 Call Status
kind: query
command: "E H1 UPHN }"
params: []
notes: "Response: X10) = 0 (inactive) or 1 (active). Verbose 2/3: UphnH1* X10)]"
# ---------- DSP Audio Level Control (gain/trim/mute) ----------
# Applies to all gain/trim/attenuation blocks via OID. X5% selects the OID.
- id: set_gain_level
label: Set Gain Level
kind: action
command: "E G X5% * X6) AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
description: |
Target OID. See Object ID (OID) Number Tables (pp.55-58):
Mic/Line Input Gain: 40000-40011
Mic/Line Pre-mixer: 40100-40111
Aux Input Gain: 40012-40019
Aux Input Pre-mixer: 40112-40119
Virtual Return Pre: 50100-50115 (A-P)
Expansion Bus Pre: 50200-50247 (AT In / EXP 1-48)
Line Output Post-trim:60100-60107
Aux Output Post-trim: 60108-60115
EXP Output Post-trim: 60116-60131
Line Output Atten: 60000-60007
Aux Output Gain: 60008-60015
EXP Output Atten: 60016-60031
Mix-point OIDs (pp.59-65): 20000-23531 covering Mic/Line, Aux, Virtual
Return, Expansion Bus inputs to Analog/Aux/EXP Output/Virtual Send mix matrices.
- name: gain_value
source_symbol: X6)
type: integer
description: |
dB value using 10x multiplier, no decimals. E.g. +10.4 dB = 104, -3.2 dB = -32.
Ranges:
Mic/Line input (analog src): -18 to +80 dB
Mic/Line input (digital src): -18 to +24 dB (use H param, not G)
Pre-mixer / Virtual return: -100 to +12 dB
Post-mixer trim: -12 to +12 dB (cannot be muted)
Output attenuation: -100 to 0 dB
notes: "Verbose response: DsG X5% * X6)]. Example: E G40000*120AU} sets mic/line input 1 to +12.0 dB."
- id: read_gain_level
label: Read Gain Level
kind: query
command: "E G X5% AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
notes: "Verbose response: DsG X5% * X6)]."
# ---------- Audio Group Master Commands ----------
- id: set_group_fader_value
label: Set Group Fader Value
kind: action
command: "E D X6# * X6$ GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
description: "1 through 64."
- name: fader_value
source_symbol: X6$
type: integer
description: |
dB in 0.1 dB increments via 10x multiplier, negatives, no decimals.
Valid range depends on group gain-block type:
-180 to 800 (-18.0 to +80.0 dB)
-1000 to 120 (-100.0 to +12.0 dB)
-120 to 120 (-12.0 to +12.0 dB)
-1000 to 0 (-100.0 to 0.0 dB)
notes: "Example: E D2*-239GRPM} sets group 2 to -29.3 dB. Response: GrpmD X6# * X6$]."
- id: increment_group_fader
label: Increment Group Fader Value
kind: action
command: "E D X6# * X6% + GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
- name: increment
source_symbol: X6%
type: integer
description: "dB x10 to raise. + after number."
notes: "Response: GrpmD X6# * X6$]."
- id: decrement_group_fader
label: Decrement Group Fader Value
kind: action
command: "E D X6# * X6% - GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
- name: decrement
source_symbol: X6%
type: integer
description: "dB x10 to lower. - after number."
- id: view_group_fader_value
label: View Group Fader Value
kind: query
command: "E D X6# GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
notes: "Verbose modes 0/1 simplified to X6$]."
- id: mute_group
label: Mute a Group
kind: action
command: "E D X6# * 1 GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
notes: "Mutes all blocks in group. Response: GrpmD X6# *1]"
- id: unmute_group
label: Unmute a Group
kind: action
command: "E D X6# * 0 GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
- id: view_group_mute_value
label: View Group Mute Value
kind: query
command: "E D X6# GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
notes: "Same opcode as view_group_fader_value; X6@ always unsigned/negative."
- id: set_group_soft_limits
label: Set Group Soft Limits
kind: action
command: "E L X6# * X6^ [upper] * X6^ [lower] GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
- name: upper_limit
source_symbol: X6^
type: integer
description: "dB x10."
- name: lower_limit
source_symbol: X6^
type: integer
description: "dB x10."
notes: "Example: E L2*60*-60GRPM} sets upper +6.0 dB, lower -6.0 dB."
- id: view_soft_limits
label: View Soft Limits
kind: query
command: "E L X6# GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
- id: view_group_type
label: View Group Type
kind: query
command: "E P X6# GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
notes: "Response: GrpmP X6# * X6&]. X6& = 6 (gain), 12 (mute), 21 (meter)."
- id: view_group_members
label: View Group Members
kind: query
command: "E O X6# GRPM }"
params:
- name: group_number
source_symbol: X6#
type: integer
notes: "Response: GrpmO X6# * X5%[1] * X5%[2] * ... * X5%[n]]"
# ---------- Unsolicited Meter Groups ----------
- id: set_unsolicited_meter_rate
label: Set Unsolicited Meter Response Rate
kind: action
command: "E R X6* GRPU }"
params:
- name: rate
source_symbol: X6*
type: integer
description: "1-10 (fw < v1.11.0000-b006); 1-25 (fw >= v1.11.0000-b006). Default 1."
notes: "Global on old fw; session-based on newer fw."
- id: view_unsolicited_meter_rate
label: View Unsolicited Meter Response Rate
kind: query
command: "E R GRPU }"
params: []
- id: set_unsolicited_meter_group
label: Set Unsolicited Meter Group
kind: action
command: "E G X6( GRPU }"
params:
- name: meter_group
source_symbol: X6(
type: integer
description: "0 disables; 1-64 enables a meter group. 0 at power on."
- id: view_unsolicited_meter_group
label: View Unsolicited Meter Group
kind: query
command: "E G GRPU }"
params: []
- id: view_oid_members_in_meter_group
label: View OID Members in Meter Group
kind: query
command: "E O X9* GRPM }"
params:
- name: meter_group_number
source_symbol: X9*
type: integer
description: "1 through 64."
- id: enable_meters_in_meter_group
label: Enable Meters in Meter Group
kind: action
command: "E D X9* * 1 GRPM }"
params:
- name: meter_group_number
source_symbol: X9*
type: integer
- id: disable_meters_in_meter_group
label: Disable Meters in Meter Group
kind: action
command: "E D X9* * 0 GRPM }"
params:
- name: meter_group_number
source_symbol: X9*
type: integer
# ---------- Aux Input 1 through 8 ----------
- id: set_aux_input_source_mode
label: Set Aux Input Source Mode
kind: action
command: "E D X5* * X7) AU }"
params:
- name: target_oid
source_symbol: X5*
type: integer
description: "Aux input OID (40012-40019)."
- name: source_mode
source_symbol: X7)
type: integer
description: "0=Disabled; 1-8=File/Tone Player 1-8; 9-16=USB Rx channels; 17-24=VoIP Line 1-8 Rx."
- id: get_aux_input_source_mode
label: Get Aux Input Source Mode
kind: query
command: "E D X5* AU }"
params:
- name: target_oid
source_symbol: X5*
type: integer
- id: set_aux_input_mute
label: Set Aux Input Mute
kind: action
command: "E M X5* * X6) AU }"
params:
- name: target_oid
source_symbol: X5*
type: integer
- name: mute
source_symbol: X6)
type: integer
description: "1 = Off, 2 = Engaged."
- id: get_aux_input_mute_status
label: Get Aux Input Mute Status
kind: query
command: "E M X5* AU }"
params:
- name: target_oid
source_symbol: X5*
type: integer
- id: set_aux_input_analog_gain
label: Set Aux Input Analog Gain
kind: action
command: "E G X5* * X5( AU }"
params:
- name: target_oid
source_symbol: X5*
type: integer
- name: gain_value
source_symbol: X5(
type: integer
description: "dB x10 in 0.1 dB steps."
- id: read_aux_input_gain
label: Read Aux Input Gain
kind: query
command: "E G X5* AU }"
params:
- name: target_oid
source_symbol: X5*
type: integer
# ---------- Aux Output 1 through 8 ----------
- id: set_aux_output_mode
label: Set Aux Output Mode
kind: action
command: "E D X5% * X7# AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
description: "Aux output OID (60008-60015)."
- name: output_mode
source_symbol: X7#
type: integer
description: "0=Disabled; 1-8=USB Tx channels; 9-16=VoIP Line 1-8 Tx."
- id: get_aux_output_mode
label: Get Aux Output Mode
kind: query
command: "E D X5% AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
- id: set_aux_output_mute
label: Set Aux Output Mute
kind: action
command: "E M X5% * X6@ AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
- name: mute
source_symbol: X6@
type: integer
description: "1 = Off, 2 = Engaged."
- id: get_aux_output_mute_status
label: Get Aux Output Mute Status
kind: query
command: "E M X5% AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
- id: set_aux_output_attenuation
label: Set Aux Output Attenuation
kind: action
command: "E G X5% * X6) AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
- name: gain_value
source_symbol: X6)
type: integer
- id: read_aux_output_attenuation
label: Read Aux Output Attenuation Level
kind: query
command: "E G X5% AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
# ---------- Automixer Gate Monitoring ----------
- id: get_automixer_gate_status
label: Get Current Automixer Gate Status
kind: query
command: "E J X9( AU }"
params:
- name: target_oid
source_symbol: X9(
type: integer
description: "Automixer OID (see Automixer OIDs, p.58)."
notes: "Response: X7$ = 0 (disabled) or 1024 (enabled)."
# ---------- Signal Level Monitoring (SLM) ----------
- id: set_slm_status
label: Set SLM Status
kind: action
command: "E J X5% * X7^ AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
- name: threshold
source_symbol: X7^
type: integer
description: "0=disabled; 0001-2000 = -0.1 to -200.0 dBFS threshold."
notes: "Response: DsJ X5% * X7^]"
- id: get_current_threshold_status
label: Get Current Threshold Status
kind: query
command: "E J X5% AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
# ---------- VoIP Call Control ----------
- id: voip_end_call
label: End Call
kind: action
command: "E END X8) , X8! VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
description: "1 through 8."
- name: appearance
source_symbol: X8!
type: integer
description: "1 through 8 (1 = originating two-party call)."
notes: "Response: VoipEND X8) , X8! , X8#]"
- id: voip_end_call_all_appearances
label: End Call on All Appearances
kind: action
command: "E END X8) VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
notes: "Response: VoipEND X8) ,0, X8#]"
- id: voip_dial_string
label: Dial String
kind: action
command: "E DIAL X8) , X8@ VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: phone_number
source_symbol: X8@
type: string
description: "0-9, *, #. No spaces."
notes: "Response: VoipDIAL X8) , X8@ , X8#]"
- id: voip_dial_digits
label: Dial Digits
kind: action
command: "E DD X8) , X8! , X8@ VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
- name: phone_number
source_symbol: X8@
type: string
notes: "Response: VoipDD X8) , X8! , X8@ , X8#]"
- id: voip_answer
label: Answer
kind: action
command: "E ANS X8) , X8! VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
notes: "Response: VoipANS X8) , X8! , X8#]"
- id: voip_reject
label: Reject
kind: action
command: "E REJ X8) , X8! VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
notes: "Response: VoipREJ X8) , X8! , X8#]"
- id: voip_hold
label: Hold
kind: action
command: "E HOLD X8) , X8! , X8& VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
- name: hold_status
source_symbol: X8&
type: integer
description: "0 = off, 1 = on hold."
notes: "Response: VoipHOLD X8) , X8! , X8& , X8#]"
- id: voip_transfer
label: Transfer
kind: action
command: "E XFER X8) , X8! , X8@ VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
- name: phone_number
source_symbol: X8@
type: string
notes: "Response: VoipXFER X8) , X8! , X8@]"
# ---------- VoIP Call Settings ----------
- id: voip_set_do_not_disturb
label: Set Do Not Disturb
kind: action
command: "E DND X8) , X8$ VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: operating_state
source_symbol: X8$
type: integer
description: "0 = enable, 1 = disable."
notes: "Response: VoipDND X8) , X8$]"
- id: voip_get_do_not_disturb
label: Get Do Not Disturb Status
kind: query
command: "E DND X8) VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- id: voip_set_auto_answer
label: Set Auto Answer
kind: action
command: "E AA X8) , X8% VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: auto_answer_mode
source_symbol: X8%
type: integer
description: "0 = disabled, 1 = delay (seconds), 2 = follow SIP header."
notes: "Response: VoipAA X8) , X8%]"
- id: voip_get_auto_answer
label: Get Auto Answer Status
kind: query
command: "E AA X8) VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- id: voip_set_auto_answer_delay
label: Set Auto Answer Delay
kind: action
command: "E AD X8) , X8^ VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: delay_value
source_symbol: X8^
type: integer
description: "Time in seconds."
notes: "Response: VoipAD X8) , X8^]"
- id: voip_get_auto_answer_delay
label: Get Auto Answer Delay Status
kind: query
command: "E AD X8) VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
# ---------- VoIP Line Status Queries ----------
- id: voip_registration_status
label: Registration Status
kind: query
command: "E RS X8) VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
notes: "Response: VoipRS X8) , X9)]. X9) = 0 unregistered, 1 1st proxy, 2 2nd proxy, 3 none, 4 failed."
- id: voip_line_status
label: Line Status
kind: query
command: "E LS X8) , X8! VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
notes: "Response: VoipLS X8) , X8! , X9!]. X9! = 0 none, 1 inactive, 2 active, 3 on hold, 4 incoming, 5 outgoing."
- id: voip_line_status_no_index
label: Line Status (Without Index)
kind: query
command: "E LS X8) VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
notes: "Returns 8 X9! appearance entries."
- id: voip_caller_name
label: Caller Name
kind: query
command: "E NAME X8) , X8! VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
notes: "Response: VoipNAME X8) , X8! , X8* , X9&]"
- id: voip_duration
label: Duration
kind: query
command: "E DUR X8) , X8! VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
notes: "Response: VoipDUR X8) , X8! , X9@]. X9@ = HH:MM:SS."
- id: voip_codec
label: Codec
kind: query
command: "E CD X8) , X8! VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
notes: "Response: VoipCD X8) , X8! , X9#]"
- id: voip_jitter_rx
label: Jitter Rx
kind: query
command: "E JR X8) , X8! VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
- name: appearance
source_symbol: X8!
type: integer
notes: "Response: VoipJR X8) , X8! , X9$ , X9% , X9^] (jitter ms, packet drops, total packets)."
- id: voip_line_extension
label: Line Extension
kind: query
command: "E LE X8) VOIP }"
params:
- name: line_number
source_symbol: X8)
type: integer
notes: "Response: VoipLE X8) , X9& , X8*]"
- id: restore_device_configuration
label: Restore Device Configuration
kind: action
command: "E 0* X2& XF }"
params:
- name: config_type
source_symbol: X2&
type: integer
description: "0 = IP configuration 2 = Device-specific parameters"
notes: "Response: Cnfg0* X2&]. The complete source supplies the restore row referenced as truncated in the retained original notes."
- id: enable_phantom_power
label: Enable Phantom Power
kind: action
command: "E Z X5% *1AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
description: "See Object ID (OID) Number Tables on page 55."
notes: "Phantom power is only available on mic/line inputs 1 through 8. Response: DsZ X5% *1 ]"
- id: disable_phantom_power
label: Disable Phantom Power
kind: action
command: "E Z X5% *0AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
description: "See Object ID (OID) Number Tables on page 55."
notes: "Phantom power is only available on mic/line inputs 1 through 8. Response: DsZ X5% *0 ]"
- id: phantom_power_status
label: Phantom Power Status
kind: query
command: "E Z X5% AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
description: "See Object ID (OID) Number Tables on page 55."
notes: "Phantom power is only available on mic/line inputs 1 through 8. Response: DsZ X5% * X6!]. X6! = 0 = Disabled (default) 1 = Enabled"
- id: read_meter_level
label: Read Meter Level
kind: query
command: "E V X5% AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
description: "See Object ID (OID) Number Tables on page 55."
notes: "Metering is available on all input gain and output attenuation blocks. Response: X7! * X7@]. X7@ = -150.0 dBFS to 0.0 dBFS (1500 to 0000)."
- id: enable_meter_updates
label: Enable Meter Updates
kind: action
command: "E V X5% * X7! AU }"
params:
- name: target_oid
source_symbol: X5%
type: integer
description: "See Object ID (OID) Number Tables on page 55."
- name: update_status
source_symbol: X7!
type: integer
description: "1 = Disabled 2 = Enabled"
notes: "Metering is available on all input gain and output attenuation blocks. Response: DsV X5% * X7!]. The Metering table defines X7! as 1/2; the general symbol key elsewhere defines it as 0/1."
- id: reset_sis_over_ssh_port_map
label: Reset SIS-over-SSH Port Map
kind: action
command: "E B X5$ *22023PMAP }"
params:
- name: nic
source_symbol: X5$
type: integer
description: "1 = LAN 1 2 = LAN 2"
notes: "Reset port to default 22023. Response: PmapB• X5$ *22023 ]. The complete source supplies this value despite the retained original truncation notes."
Feedbacks
# Query-response feedbacks (representative states; the corresponding query
# actions above carry the verbatim ASCII request).
- id: firmware_version_state
type: string
values: ["x.xx"] # UNRESOLVED: full version range not bounded in source
query: query_firmware_version
query_command: "Q"
- id: dhcp_state
type: enum
values: ["0", "1"]
query: view_dhcp_mode
query_command: "EDH}"
- id: verbose_mode_state
type: enum
values: ["0", "1", "2", "3"]
query: view_verbose_mode
query_command: "ECV}"
- id: ntp_status_state
type: enum
values: ["0", "1"]
query: view_ntp_status
query_command: "E NTEN }"
- id: snmp_access_state
type: enum
values: ["0", "1"]
query: view_snmp_access_setting
query_command: "E ESNMP }"
- id: session_security_level
type: enum
values: ["11", "12"] # 11=user, 12=administrator
query: view_session_security_level
query_command: "E CK }"
- id: macro_status_state
type: integer
query: get_macro_status
query_command: "E S X5! MCRO }"
- id: player_play_state
type: enum
values: ["0", "1"]
query: player_status
query_command: "EX4* PLAY }"
- id: player_repeat_state
type: enum
values: ["0", "1"]
query: get_player_repeat_status
query_command: "E M X4* CPLY }"
- id: usb_call_status
type: enum
values: ["0", "1"]
query: view_usb_call_status
query_command: "E H1UPHN }"
- id: gain_level
type: integer
query: read_gain_level
query_command: "E G X5% AU }"
- id: group_fader_value
type: integer
query: view_group_fader_value
query_command: "E D X6# GRPM }"
- id: group_mute_state
type: enum
values: ["0", "1"]
query: view_group_mute_value
query_command: "E D X6# GRPM }"
- id: group_type
type: enum
values: ["6", "12", "21"] # 6=gain, 12=mute, 21=meter
query: view_group_type
query_command: "E P X6# GRPM }"
- id: automixer_gate_status
type: enum
values: ["0", "1024"]
query: get_automixer_gate_status
query_command: "E J X9( AU }"
- id: aux_input_mute_state
type: enum
values: ["0", "1"]
query: get_aux_input_mute_status
query_command: "E M X5* AU }"
- id: aux_output_mute_state
type: enum
values: ["0", "1"]
query: get_aux_output_mute_status
query_command: "E M X5% AU }"
- id: voip_registration_state
type: enum
values: ["0", "1", "2", "3", "4"]
query: voip_registration_status
query_command: "E RS X8) VOIP }"
- id: voip_call_status
type: enum
values: ["0", "1", "2", "3", "4", "5"]
query: voip_line_status
query_command: "E LS X8) , X8! VOIP }"
Variables
# Settable parameters that are not discrete actions.
- id: unit_name
type: string
max_length: 63
set: set_unit_name
- id: ip_address
type: string
default: "192.168.254.254"
set: set_ip_address
- id: subnet_mask
type: string
default: "255.255.255.0"
set: set_subnet_mask
- id: gateway_ip
type: string
default: "0.0.0.0"
set: set_gateway_ip_address
- id: dns_server_ip
type: string
set: set_dns_server_ip
- id: serial_baud_rate
type: integer
default: 38400
set: configure_serial_parameters
- id: connection_timeout_seconds
type: integer
range: "10 to 650000 (1 step = 10 s; param range 1-65000)"
default: 300
set: set_global_ip_port_timeout
- id: admin_password
type: string
max_length: 128
set: set_admin_password
- id: user_password
type: string
max_length: 128
set: set_user_password
- id: verbose_mode
type: enum
values: ["0", "1", "2", "3"]
set: set_verbose_mode
- id: audio_gain
type: integer
unit: "dB x10 (10x multiplier, no decimals)"
set: set_gain_level
- id: group_fader
type: integer
unit: "dB x10 (0.1 dB increments)"
set: set_group_fader_value
- id: ntp_ip_address
type: string
set: set_ntp_ip_address
Events
# Unsolicited messages the device sends. See "Device-Initiated Power-Up Message"
# (p.30), "Unsolicited Responses" (VoIP p.53), "Asynchronous Macro Responses"
# (p.46), "Playback finished" (p.46), and unsolicited meter/SLM/automixer
# responses (pp.49-52).
- id: power_up_copyright_message
trigger: "First power-on over RS-232, or first Telnet connection opened."
payload: "© Copyright 2016-2022, Extron Electronics DMP 128 Plus {model}, V {x.xx}, 60-{nnnn}-{nn} ]"
notes: "{model} = full model name; V{x.xx} = firmware; 60-{nnnn}-{nn} = part number. Date/time line follows on Telnet only."
- id: password_prompt
trigger: "Telnet/Web connection when a password is configured."
payload: "] Password"
notes: "Repeated until correct admin or user password is entered."
- id: login_administrator
trigger: "Successful administrator password entry."
payload: "] Login Administrator ]"
- id: login_user
trigger: "Successful user password entry."
payload: "] Login User ]"
# Asynchronous macro responses:
- id: macro_started
payload: "McroSTARTED X5!]"
- id: macro_finished
payload: "McroFINISHED X5!]"
- id: macro_failed
payload: "McroFAILED X5! * X5@]"
- id: macro_killed
payload: "McroKILLED X5! * X5@]"
# Player unsolicited:
- id: playback_finished
payload: "Play X4* *0 ]"
# Unsolicited meter group values (verbose modes 1/3 only):
- id: unsolicited_meter_group_values
payload: "GrpmV X6# * <val>1 * <val>2 * ... * <val>n ]"
notes: "Values 0-1500 (0.0 to -150.0 dBFS). Order = numerical OID order in group."
# Signal Level Monitoring (SLM) unsolicited:
- id: slm_meter_value
payload: "DsV X5% * X7% * X7& * X7*]"
notes: "OID, meter on/off, level (0.0 to -200.0 dBFS), above/below threshold."
# Automixer gate unsolicited:
- id: automixer_gate_status_update
payload: "DsV X5% * X7% * X7( * X10!]"
notes: "OID, meter on/off, gate signal level, gate status (closed/opened)."
# VoIP unsolicited responses:
- id: voip_busy
payload: "VoipBusy X8) , X8!]"
- id: voip_rejected
payload: "VoipRejected X8) , X8!]"
- id: voip_unreachable
payload: "VoipUnreachable X8) , X8!]"
- id: voip_terminated
payload: "VoipTerminated X8) , X8!]"
- id: voip_incoming
payload: "VoipIncoming X8) , X8! , X8* , X9& , X8(]"
- id: voip_registration_status_event
payload: "VoipRS X8) , X9)]"
- id: voip_line_status_event
payload: "VoipLS X8) , X9! , X9! , X9! , X9! , X9! , X9! , X9! , X9!]"
notes: "8 X9! appearance entries."
- id: voip_remote_cancel
payload: "VoipRemoteCancel X8) , X8!]"
# Error responses (issued when a command cannot be executed):
- id: error_e10
code: E10
meaning: Unrecognized command
- id: error_e12
code: E12
meaning: Invalid port number
- id: error_e13
code: E13
meaning: Invalid parameter
- id: error_e14
code: E14
meaning: Not valid for this configuration
- id: error_e17
code: E17
meaning: Invalid command for signal type
- id: error_e18
code: E18
meaning: System timed out
- id: error_e22
code: E22
meaning: Busy when not set
- id: error_e24
code: E24
meaning: Privilege violation
- id: error_e25
code: E25
meaning: Device not present
- id: error_e26
code: E26
meaning: Maximum connections exceeded
- id: error_e27
code: E27
meaning: Bad filename or file not found
- id: error_e28
code: E28
meaning: Bad file name or file not found
- id: error_e31
code: E31
meaning: Attempt to break port pass-through
Macros
# The DMP 128 Plus exposes a macro subsystem (run/kill/status/name/power-on, see
# Macro Commands above) but the source documents no named multi-step macro
# sequences. Macro step contents are authored in DSP Configurator, not via SIS.
# UNRESOLVED: source documents no named multi-step macro sequences via SIS.
Safety
confirmation_required_for: []
interlocks: []
# UNRESOLVED: source contains no explicit safety warnings, interlock procedures,
# or power-on sequencing requirements. Destructive reset commands execute
# immediately on receipt:
# - Full factory reset (E ZQQQ }) deletes all user content and reverts to default.
# - Partial factory reset (E ZXXX }), flash reset (E ZFFF }), and
# "reset all device settings" (E ZY }) execute without confirmation.
# Reset Modes (rear-panel button, p.9) also delete content at certain hold times.
Notes
- The "Plus" family differs from the legacy DMP 128: adds VoIP (V models), Dante/AT expansion bus, virtual returns A-P (16), aux inputs/outputs (8 each), file/tone players (8), macros (64), NTP, SNMP, per-NIC port mapping (PMAP), Signal Level Monitoring, and unsolicited meter groups. RS-232 baud is 38400 (higher than most Extron products) for both families.
- SIS framing:
E ... }(Esc + payload + soft-CR}). Device responses end with CR/LF]. No start delimiter required beyond the Esc prefix. Commands case-insensitive except where noted. - RS-232 default verbose mode = 1 (verbose); Telnet default = 0 (clear). Use verbose 1 or 3 on Telnet to receive unsolicited change notices from other sockets/serial.
- Default IP: 192.168.254.254 (LAN 1); 192.168.1.254 (LAN 2 on V models). Default subnet 255.255.255.0, gateway 0.0.0.0, DHCP off.
- Auth is IP-only: factory password = device serial number; up to 128 chars; case-sensitive; cannot contain
|; cannot be a single space. RS-232/USB connections never prompt. Default after factory reset = no password. - Default connection timeout 5 minutes; Extron recommends leaving at default and periodically issuing
Qto keep connection alive. - Audio dB encoding: direct 10x multiplier, no offset (unlike legacy DMP 128's +2048 offset). E.g. +10.4 dB =
104, -3.2 dB =-32. Gain ranges vary by block type. - Digital I/O (8 channels) supports action types 0-16 (mutes, group mutes, macros, presets) via X3% with trigger modes (level/edge/toggle). See symbol key pp.33-34.
- Dante passthrough: use
wfor Esc and|for CR inside remote commands; closing}required. Requires Verbose mode 1/3. - HTML reserved characters rejected in names/passwords/filenames:
{space (OK for names)} + ~ , @ = ' { } [ ] < > \" ; : \ ?` (verbatim, p.31). - Mix-point routing is achieved by mute/unmute of the mix-point OID; there is no separate "route" opcode. To route input N to output M, look up the mix-point address (pp.59-65) and send
E M{oid}*0AU}(unmute = route) orE M{oid}*1AU}(mute = break). - On AT models, the last 16 channels can be set as AT Inputs (AT In 33-48) or Expansion Inputs (EXP 1-16).
Provenance
source_domains:
- media.extron.com
source_urls:
- https://media.extron.com/public/download/files/userman/dmp_128_plus_68-2826-01_M.pdf
- https://media.extron.com/public/download/files/userman/dmp_64_plus_68-3291-01_E.pdf
- https://media.extron.com/public/download/files/userman/DMP_128_68-2036-01_revF.pdf
- https://media.extron.com/public/download/files/userman/DMP64_68-1790-01_D.pdf
- https://media.extron.com/public/download/files/userman/dmp_128_flexplus_68-3428-01_E.pdf
retrieved_at: 2026-07-02T04:10:33.065Z
last_checked_at: 2026-10-07T21:04:02.014Z
Verification Summary
verdict: verified
checked_at: 2026-10-07T21:04:02.014Z
matched_actions: 241
action_count: 241
confidence: medium
summary: "All 241 action units match source command tables and transport values are supported; generic audio mute/unmute appear only in spec Notes, so coverage is near-complete. (13 unresolved item(s) noted in Known Gaps.)"
Known Gaps
- "Power on/off commands are not documented in source; the device appears always-on when powered; no SIS power command exists."
- "Firmware version compatibility range not stated in source."
- "SKU variants (V / AT / C) are referenced throughout but the full model enumeration is not stated in the source excerpt."
- "SIS-over-SSH reset-to-default port value was truncated in the source excerpt."
- "the \"Reset SIS-over-SSH port map\" command was truncated in the"
- "full version range not bounded in source"
- "source documents no named multi-step macro sequences via SIS."
- "source contains no explicit safety warnings, interlock procedures,"
- "firmware version compatibility range not stated in source."
- "SKU variants (V / AT / C) referenced throughout but full model enumeration not stated in the source excerpt; only \"DMP 128 Plus\" base model confirmed."
- "\"Reset SIS-over-SSH port map\" command truncated in source; default reset value (likely 22) not shown verbatim."
- "\"Restore device configuration\" command (E 0*X2&XF}) row truncated in source; response shape not captured."
- "CISG gateway X% symbol reused for both IP and gateway within one command — the source explicitly disambiguates by position, not by distinct symbol."
From the AI4AV catalog (https://ai4av.net) · ODbL-1.0