AI4AVSummary
Light-protocol RS-232 / Ethernet interface for the Domintell home-automation bus. Third-party software exchanges ASCII Light Protocol frames with the host over serial or UDP; variant modules (DRS23201, DRS23202, DETH02) expose configuration-string I/O, hex I/O, and session-managed IP control respectively.
Transport
protocols:
- serial
- udp
serial:
baud_rate: 57600 # DRS23202 fixed; DRS23201 selectable: 1200, 2400, 4800, 9600, 19200, 38400, 57600
data_bits: 8
parity: none
stop_bits: 1
flow_control: none
addressing:
port: 17481 # DETH02 default; source notes "can be changed"
auth:
type: password # DETH02: "Possibility to set a password"; DRS23202: no auth described
Notes on transport:
- DB-9 wiring: TX = pin 2, RX = pin 3, GND = pin 5; pins 1/7/8/9 = NC; pins 4/6 reserved (handshake, unused).
- Recommended cable: straight female-male DB9 to a computer, null-modem male-male DB9 to a target device such as a projector.
- DETH02: UDP only, single concurrent client.
- Inter-frame gap on RS-232: minimum 25 ms OR use the reserved
&character. - Maximum Light Protocol message length: 30 characters.
- Reserved characters:
%(starts additional parameters),&(frame concat / inter-message gap).
Traits
- queryable
- levelable
- routable
Actions
- id: ping
label: Ping (DETH02)
kind: action
command: "PING"
params: []
- id: mod_version_query
label: Module Version Query
kind: query
command: "MOD_VERSION"
params: []
- id: login
label: Login (DETH02)
kind: action
command: "LOGIN"
params: []
- id: login_with_password
label: Login with Password (DETH02)
kind: action
command: "LOGIN{encrypted}"
params:
- name: encrypted
type: string
description: Password encrypted with libdeth 2.0+ deth_encryptpsw(), 4-10 ASCII chars; SDK appends "LOGIN" suffix
- id: logout
label: Logout (DETH02)
kind: action
command: "LOGOUT"
params: []
- id: hello
label: Keep Session Open (DETH02)
kind: action
command: "HELLO"
params: []
- id: appinfo
label: Download Module List (DETH02)
kind: action
command: "APPINFO"
params: []
- id: help
label: Help (DETH02)
kind: query
command: "HELP"
params: []
- id: lp_dim_set
label: Set Dimmer Percent (Light Protocol)
kind: action
command: "DIM{serial}-%D{percent}"
params:
- name: serial
type: string
description: 3-char module type (DIM) then 6-char hex serial (e.g. 19F), no space
- name: output
type: integer
description: Output number (1-8) on DDIM01
- name: percent
type: integer
description: Dimmer value 0-100 percent
- id: lp_dim_start
label: Start Dim Ramp (Light Protocol)
kind: action
command: "DIM{serial}-{output}%DB"
params:
- name: serial
type: string
description: DDIM01 module serial, 6 hex chars
- name: output
type: integer
description: Output number 1-8
- id: lp_dim_stop
label: Stop Dim Ramp (Light Protocol)
kind: action
command: "DIM{serial}-{output}%DE"
params:
- name: serial
type: string
description: DDIM01 module serial, 6 hex chars
- name: output
type: integer
description: Output number 1-8
- id: lp_dim_inc
label: Increase Dimmer by Step (Light Protocol)
kind: action
command: "DIM{serial}-{output}%I%D{step}"
params:
- name: serial
type: string
description: DDIM01 module serial, 6 hex chars
- name: output
type: integer
description: Output number 1-8
- name: step
type: integer
description: Step in percent (clamps at 100)
- id: lp_dim_dec
label: Decrease Dimmer by Step (Light Protocol)
kind: action
command: "DIM{serial}-{output}%O%D{step}"
params:
- name: serial
type: string
description: DDIM01 module serial, 6 hex chars
- name: output
type: integer
description: Output number 1-8
- name: step
type: integer
description: Step in percent (clamps at 0)
- id: lp_d10_set
label: Set 0-10V Output Percent
kind: action
command: "D10{serial}-{output}%D{percent}"
params:
- name: serial
type: string
description: DOUT10V02 module serial, 6 hex chars
- name: output
type: integer
description: Output number on DOUT10V02
- name: percent
type: integer
description: Output value 0-100 percent
- id: lp_d10_inc
label: Increase 0-10V Output by Step
kind: action
command: "D10{serial}-{output}%I%D{step}"
params:
- name: serial
type: string
description: DOUT10V02 module serial, 6 hex chars
- name: output
type: integer
description: Output number on DOUT10V02
- name: step
type: integer
description: Step in percent
- id: lp_d10_dec
label: Decrease 0-10V Output by Step
kind: action
command: "D10{serial}-{output}%O%D{step}"
params:
- name: serial
type: string
description: DOUT10V02 module serial, 6 hex chars
- name: output
type: integer
description: Output number on DOUT10V02
- name: step
type: integer
description: Step in percent
- id: lp_dmx_set_channel
label: Set DMX Channel Value (DDMX01)
kind: action
command: "DMX{serial}-{device}-{channel}%X{value_hex}"
params:
- name: serial
type: string
description: DDMX01 module serial, 6 hex chars
- name: device
type: integer
description: DMX device slot
- name: channel
type: integer
description: DMX channel within device
- name: value_hex
type: string
description: DMX value 0x00-0xFF, as hex
- id: lp_dali_request
label: DALI Ballast Request (DINTDALI01)
kind: action
command: "DAL{serial}-{address}%D{percent}"
params:
- name: serial
type: string
description: DINTDALI01 module serial, 6 hex chars
- name: address
type: string
description: 2-hex-digit DALI address
- name: percent
type: integer
description: Dimmer percent 0-100
- id: lp_bu_toggle
label: Toggle DPBUxx Output
kind: action
command: "BU{n}{serial}-{output}"
params:
- name: n
type: integer
description: DPBU channel count 1/2/4/6
- name: serial
type: string
description: 6 hex chars
- name: output
type: integer
description: Output number 1-n
- id: lp_bu_status
label: DPBUxx Input/Output Status Query
kind: query
command: "BU{n}{serial}%S"
params:
- name: n
type: integer
description: DPBU channel count 1/2/4/6
- name: serial
type: string
description: 6 hex chars
- id: lp_trv_toggle
label: Toggle Shutter (DTRV01)
kind: action
command: "TRV{serial}-{shutter}"
params:
- name: serial
type: string
description: DTRV01 serial, 6 hex chars
- name: shutter
type: integer
description: Shutter number 1-4
- id: lp_trv_up
label: Shutter Up (DTRV01)
kind: action
command: "TRV{serial}-{shutter}%H"
params:
- name: serial
type: string
description: DTRV01 serial, 6 hex chars
- name: shutter
type: integer
description: Shutter number 1-4
- id: lp_trv_down
label: Shutter Down (DTRV01)
kind: action
command: "TRV{serial}-{shutter}%L"
params:
- name: serial
type: string
description: DTRV01 serial, 6 hex chars
- name: shutter
type: integer
description: Shutter number 1-4
- id: lp_trv_stop
label: Shutter Stop (DTRV01)
kind: action
command: "TRV{serial}-{shutter}%O"
params:
- name: serial
type: string
description: DTRV01 serial, 6 hex chars
- name: shutter
type: integer
description: Shutter number 1-4
- id: lp_bir_toggle
label: Toggle DBIR01 Output
kind: action
command: "BIR{serial}-{output}"
params:
- name: serial
type: string
description: DBIR01 serial, 6 hex chars
- name: output
type: integer
description: Output 1-8
- id: lp_bir_set
label: Set DBIR01 Output
kind: action
command: "BIR{serial}-{output}%I"
params:
- name: serial
type: string
description: DBIR01 serial, 6 hex chars
- name: output
type: integer
description: Output 1-8
- id: lp_bir_reset
label: Reset DBIR01 Output
kind: action
command: "BIR{serial}-{output}%O"
params:
- name: serial
type: string
description: DBIR01 serial, 6 hex chars
- name: output
type: integer
description: Output 1-8
- id: lp_amp_volume_set
label: Set Amplifier Output Volume + Source
kind: action
command: "AMP{serial}-{output}%D{vol}%A{aux}"
params:
- name: serial
type: string
description: DAMPLI01 serial, 6 hex chars
- name: output
type: integer
description: Output number on DAMPLI01
- name: vol
type: integer
description: Volume 0-100 (decimal in source: 50, 60, ...)
- name: aux
type: integer
description: Auxiliary source 1-4; 5 = Tuner
- id: lp_amp_tuner_set
label: Set Amplifier Tuner Output
kind: action
command: "AMP{serial}-{output}%D{vol}%F{freq_mhz}%A{aux}"
params:
- name: serial
type: string
description: DAMPLI01 serial, 6 hex chars
- name: output
type: integer
description: Output number on DAMPLI01
- name: vol
type: integer
description: Volume 0-100
- name: freq_mhz
type: string
description: Tuner frequency, decimal Mhz (e.g. 99.1)
- name: aux
type: integer
description: Source, 5 = Tuner
- id: lp_amp_volume_inc
label: Increase Amplifier Volume by Step
kind: action
command: "AMP{serial}-{output}%I%D{step}"
params:
- name: serial
type: string
description: DAMPLI01 serial, 6 hex chars
- name: output
type: integer
description: Output number
- name: step
type: integer
description: Step percent
- id: lp_amp_volume_dec
label: Decrease Amplifier Volume by Step
kind: action
command: "AMP{serial}-{output}%O%D{step}"
params:
- name: serial
type: string
description: DAMPLI01 serial, 6 hex chars
- name: output
type: integer
description: Output number
- name: step
type: integer
description: Step percent
- id: lp_amp_status
label: Amplifier Status Query
kind: query
command: "AMP{serial}%S"
params:
- name: serial
type: string
description: DAMPLI01 serial, 6 hex chars
- id: lp_sfeer_set
label: Activate Sfeer (Scene)
kind: action
command: "SFE{n}"
params:
- name: n
type: integer
description: Scene number
- id: lp_sfeer_query
label: Sfeer Item Status Query
kind: query
command: "SFE{n}%S"
params:
- name: n
type: integer
description: Scene number
- id: lp_var_toggle
label: Toggle Software Variable
kind: action
command: "VAR{n}"
params:
- name: n
type: integer
description: Variable number in configuration appearance order
- id: lp_var_query
label: Software Variable Status (status format inferred from output example)
kind: action
command: "VAR{n}%S"
params:
- name: n
type: integer
description: Variable number
- id: lp_sys_query
label: System Variable Status Query
kind: query
command: "SYS{n}%S"
params:
- name: n
type: integer
description: System variable number
- id: lp_sys_temp_mode_set
label: Set System Temperature Mode
kind: action
command: "SYS{n}%M{mode}"
params:
- name: n
type: integer
description: System variable number
- name: mode
type: integer
description: Mode: 1=absence, 2=auto, 5=comfort, 6=frost
- id: lp_sys_reg_mode_set
label: Set System Regulation Mode
kind: action
command: "SYS{n}%R{mode}"
params:
- name: n
type: integer
description: System variable number
- name: mode
type: integer
description: Mode: 0=off, 1=heating, 2=cooling, 3=mixed
- id: lp_sys_reg_d_set
label: Set System Regulation (D variant)
kind: action
command: "SYS{n}%D{code}"
params:
- name: n
type: integer
description: System variable number
- name: code
type: integer
description: Code: 0=off, 01=heating, 2=cooling, 03=mixed
- id: lp_push_simulate
label: Simulate Button Push
kind: action
command: "{MOD}{serial}-{input}%P{code}"
params:
- name: MOD
type: string
description: Module type mnemonic (BU1/BU2/BU4/BU6, IS4/IS8, PBL, PRL, ...)
- name: serial
type: string
description: 6-char hex serial
- name: input
type: integer
description: Input/button number
- name: code
type: integer
description: 1=begin short, 2=end short, 3=begin long, 4=end long
- id: lp_module_status_query
label: Generic Module Status Query
kind: query
command: "{MOD}{serial}%S"
params:
- name: MOD
type: string
description: Module type mnemonic
- name: serial
type: string
description: 6-char hex serial
- id: lp_temperature_heat_set
label: Set Heating Setpoint (TSC-class)
kind: action
command: "{MOD}{serial}%T{temp}"
params:
- name: MOD
type: string
description: DTSC module mnemonic (TSB, LT2, T35, ...)
- name: serial
type: string
description: 6-char hex serial
- name: temp
type: string
description: Decimal temperature, e.g. 22.7
- id: lp_temperature_cool_set
label: Set Cooling Setpoint (TSC-class)
kind: action
command: "{MOD}{serial}%U{temp}"
params:
- name: MOD
type: string
description: DTSC module mnemonic (LT4, T35, ...)
- name: serial
type: string
description: 6-char hex serial
- name: temp
type: string
description: Decimal temperature, e.g. 21.5
- id: lp_zone_setpoint_set
label: T° Zone Setpoint (ZON)
kind: action
command: "ZON{n}%T{temp}"
params:
- name: n
type: integer
description: Zone number
- name: temp
type: string
description: Decimal setpoint, e.g. 15.5
- id: lp_zone_inc
label: Increment T° Zone Setpoint
kind: action
command: "ZON{n}%I"
params:
- name: n
type: integer
description: Zone number
- id: lp_zone_dec
label: Decrement T° Zone Setpoint
kind: action
command: "ZON{n}%O"
params:
- name: n
type: integer
description: Zone number
- id: lp_zone_temp_mode
label: T° Zone Temperature Mode
kind: action
command: "ZON{n}%M{mode}"
params:
- name: n
type: integer
description: Zone number
- name: mode
type: integer
description: Mode: 1=absence, 2=auto, 5=comfort, 6=frost
- id: lp_clock_set
label: Set Clock Programme
kind: action
command: "CLK{n}%K{h:m:s} {mask} {dd/mm/yy}"
params:
- name: n
type: integer
description: Clock number
- name: h_m_s
type: string
description: Time hh:mm:ss
- name: mask
type: string
description: Weekday mask byte (b0=sun, b1=mon, ...). FF disables clock.
- name: dd_mm_yy
type: string
description: dd/mm/yy
- id: lp_memo_set
label: Set Mixed Memo
kind: action
command: "MEM{n}%I"
params:
- name: n
type: integer
description: Memo number
- id: lp_memo_reset
label: Reset Mixed Memo
kind: action
command: "MEM{n}%O"
params:
- name: n
type: integer
description: Memo number
- id: lp_memo_dim_set
label: Set Dimmer Memo
kind: action
command: "MEM{n}%D{percent}"
params:
- name: n
type: integer
description: Memo number
- name: percent
type: integer
description: 0-100 dimmer percent
- id: lp_memo_dim_inc
label: Increase Dimmer Memo by Step
kind: action
command: "MEM{n}%I%D{step}"
params:
- name: n
type: integer
description: Memo number
- name: step
type: integer
description: Step percent
- id: lp_memo_dim_dec
label: Decrease Dimmer Memo by Step
kind: action
command: "MEM{n}%O%D{step}"
params:
- name: n
type: integer
description: Memo number
- name: step
type: integer
description: Step percent
- id: lp_memo_shutter_off
label: Shutter Memo Group Off
kind: action
command: "MEM{n}%O"
params:
- name: n
type: integer
description: Memo group number
- id: lp_memo_shutter_up
label: Shutter Memo Group Up
kind: action
command: "MEM{n}%H"
params:
- name: n
type: integer
description: Memo group number
- id: lp_memo_shutter_down
label: Shutter Memo Group Down
kind: action
command: "MEM{n}%L"
params:
- name: n
type: integer
description: Memo group number
- id: lp_fan_speed_set
label: DFAN Fan Speed Set
kind: action
command: "FAN{serial}-{speed}%I"
params:
- name: serial
type: string
description: DFAN serial, 6 hex chars
- name: speed
type: integer
description: 1-3 fan speed, 4=heating, 5=cooling, 6=manual mode
- id: lp_fan_auto
label: DFAN Auto Mode
kind: action
command: "FAN{serial}-6%O"
params:
- name: serial
type: string
description: DFAN serial, 6 hex chars
- id: lp_dmv_speed
label: DMV01 Speed / Auxiliary Set
kind: action
command: "DMV{serial}-{slot}%I"
params:
- name: serial
type: string
description: DMV serial, 6 hex chars
- name: slot
type: integer
description: 1-3 speed, 4=Aux1, 5=Aux2
- id: lp_bl_set
label: Push Button Lythos / Rainbow / LCD - Set Output
kind: action
command: "{MOD}{serial}-{output}%I"
params:
- name: MOD
type: string
description: Module mnemonic B81/B82/B84/B86, BR2/BR4/BR6, PBL, PRL
- name: serial
type: string
description: 6 hex chars
- name: output
type: integer
description: Output index
- id: lp_bl_reset
label: Push Button Lythos / Rainbow / LCD - Reset Output
kind: action
command: "{MOD}{serial}-{output}%O"
params:
- name: MOD
type: string
description: Module mnemonic B81/B82/B84/B86, BR2/BR4/BR6, PBL, PRL
- name: serial
type: string
description: 6 hex chars
- name: output
type: integer
description: Output index
- id: lp_pblcd_status
label: DPBTLCD02 / DPBRLCD02 Status
kind: query
command: "{MOD}{serial}%S"
params:
- name: MOD
type: string
description: PBL or PRL
- name: serial
type: string
description: 6 hex chars
- id: lp_tpv_toggle
label: Toggle TPV Shutter (DTRP02)
kind: action
command: "TPV{serial}-{shutter}"
params:
- name: serial
type: string
description: DTRP02 serial, 6 hex chars
- name: shutter
type: integer
description: Shutter 1-2
- id: lp_v24_toggle
label: Toggle DC Shutter (DTRVBT01)
kind: action
command: "V24{serial}-{shutter}"
params:
- name: serial
type: string
description: DTRVBT01 serial, 6 hex chars
- name: shutter
type: integer
description: Shutter 1
- id: lp_trp_toggle
label: Toggle Teleruptor (DTRP01)
kind: action
command: "TRP{serial}-{output}"
params:
- name: serial
type: string
description: DTRP01 serial, 6 hex chars
- name: output
type: integer
description: Output 1-4
- id: lp_led_toggle
label: Toggle DLED01 Output
kind: action
command: "LED{serial}-{output}"
params:
- name: serial
type: string
description: DLED01 serial, 6 hex chars
- name: output
type: integer
description: Output 1-4
- id: lp_i10_status
label: DIN10V Status
kind: query
command: "I10{serial}%S"
params:
- name: serial
type: string
description: DIN10V serial, 6 hex chars
- id: lp_te2_temp_mode
label: DTEM02 Temperature Mode
kind: action
command: "TE2{serial}%M{mode}"
params:
- name: serial
type: string
description: DTEM02 serial
- name: mode
type: integer
description: 1=absence
- id: lp_te2_reg_mode
label: DTEM02 Regulation Mode
kind: action
command: "TE2{serial}%R{mode}"
params:
- name: serial
type: string
description: DTEM02 serial
- name: mode
type: integer
description: 2=cooling
Feedbacks
- id: pong
type: string
values:
- "PONG"
description: Reply to PING
- id: mod_version
type: string
description: Reply to MOD_VERSION, format "MOD_VERSION=SER_Vxx" or "MOD_VERSION=ETH_Vxx_STK_Vxx"
- id: appinfo_record
type: string
description: Per-module record from APPINFO, format described in source; follows header `APPINFO (PROG M x.yy dd/mm/yy hh:mm Rev=n)` and ends with `END APPINFO - Send "HELP" from ETH.`
- id: please_upgrade
type: string
description: Banner string `!! PLEASE UPGRADE DRS23202 FIRMWARE >= NN` or `!! PLEASE UPGRADE DETH02 FIRMWARE >= NN`
- id: dim_status
type: string
description: Dimmer output frame: `DIM{serial}D p1 p2 p3 p4 p5 p6 p7 p8`, percentages as 2-digit hex
- id: outputs_octet
type: string
description: Outputs-frame code O, value is hex byte, LSB = out 0, MSB = out 7
- id: inputs_octet
type: string
description: Inputs-frame code I, value is hex byte, LSB = in 0, MSB = in 7
- id: button_event
type: string
description: `B` type, 2 bytes button number + 2 bytes (00=released, 01=pressed)
- id: temperature_t
type: string
description: Heating setpoint frame: `T{measure} {setpoint} {mode} {profile_value}`
- id: temperature_u
type: string
description: Cooling setpoint frame: `U{measure} {setpoint} {mode} {profile_value}`
- id: dmx_frame
type: string
description: `DMX{serial}-{device}X{2_hex_per_channel}` (modern) or older 2nd dash variant; channel value hex
- id: amp_sound_frame
type: string
description: `AMP{serial}S{output}-{vol}-{source}-{freq_hex}-{tens_hex}` since card version 5
- id: clock_k
type: string
description: `CLK{n}K{hh:mm:ss}-{mask}-{dd/mm/yy}-{name}[{type}]`, type ∈ {blank, SUNSET, SUNRISE, RESET}
- id: tuner_station
type: string
description: `STA{n}STU {name}[FM={vol_hex}-{freq_hex}]`
- id: temp_plage_p
type: string
description: `TPL{n}P{setpoint}-{hh:mm:ss}`
- id: profile_name
type: string
description: `TPR{n}{name}`
- id: ascii_link_output
type: string
description: Output ASCII string emitted to the third-party device, content arbitrary, configured in Domintell2 software
- id: hex_output
type: string
description: Output non-printable (hex) data block emitted by DRS23201 to third-party device
- id: session_info
type: string
description: `INFO:Session opened:INFO` / `INFO:Session closed:INFO` / `INFO:World:INFO`
Variables
# Additional Parameters are not state variables; they form the parameter language of Light
# Protocol messages. Listed here as a glossary.
- id: param_D_set
type: integer
description: "Percent assignment for dimmer / volume / 0-10V output, %Dxxx decimal"
- id: param_DB
type: string
description: "%DB - execute a Start dim on a dimmer output"
- id: param_DE
type: string
description: "%DE - execute a Stop dim on a dimmer output"
- id: param_ID
type: string
description: "%I%Dxxx - Increase dimmer/volume value by step xxx percent"
- id: param_OD
type: string
description: "%O%Dxxx - Decrease dimmer/volume value by step xxx percent"
- id: param_T_temp
type: string
description: "%Txx.x - decimal Heating setpoint"
- id: param_U_temp
type: string
description: "%Uxx.x - decimal Cooling setpoint"
- id: param_A_aux
type: integer
description: "%Ax - Sound Auxiliary selection 1..4, Tuner = 5"
- id: param_F_freq
type: string
description: "%Fxxx,xxxx - Tuner Frequency in MHz"
- id: param_I
type: string
description: "%I - set the output"
- id: param_O
type: string
description: "%O - reset the output (stop on shutters)"
- id: param_M_mode
type: integer
description: "%Mx - Temperature mode 1=absence, 2=auto, 5=comfort, 6=frost"
- id: param_R_regmode
type: integer
description: "%Rx - Regulation mode 0=off, 1=heating, 2=cooling, 3=mixed"
- id: param_H
type: string
description: "%H - shutter goes High (Up)"
- id: param_L
type: string
description: "%L - shutter goes Low (Down)"
- id: param_S
type: string
description: "%S - ask status of module (does not work with MEMO)"
- id: param_P_push
type: integer
description: "%Px - simulated push 1=Begin short 2=End short 3=Begin long 4=End long"
- id: param_K_clock
type: string
description: "%K{hh:mm:ss} {weekday_mask} {dd/mm/yy} - Clock programme"
- id: param_X_dmx
type: string
description: "%X{hex} - DMX channel value"
Events
# UNRESOLVED: source enumerates output Light Protocol frames but does not name a single
# discrete "event" channel; subscribers parse the continuous ASCII stream from the
# interface. Examples appear in the Feedbacks section.
Macros
# UNRESOLVED: source does not document a macro/sequencing layer at the protocol surface.
# Scenes ("Sfeer") exist in Domintell2 configuration but are triggered by single
# SCENE-style actions above (lp_sfeer_set), not multi-step macro scripts.
Safety
confirmation_required_for: []
interlocks:
- description: |
Do NOT connect the Domintell bus on the DETH0x RJ45 connector; this can cause
fatal damage to the DETH0x module. The RJ45 is intended for LAN only.
- description: |
On multi-module installations with multiple DRS23202 and DETH02, configuration
software must be ≥ 1.19.11 and firmware must be ≥ v15 (DRS23202) or ≥ v7 (DETH02).
- description: |
Output Light Protocol from Domintell is only available in installations with fewer
than 241 modules.
- description: |
DETH02 allows only one concurrent client; always LOGOUT before exiting the
application to release the module for other clients.
- description: |
Wait for the previous reply before sending the next DETH02 command; new commands
are dropped otherwise. Specific DETH0x commands cannot be concatenated with `&`
and exactly one DETH0x command may be sent per UDP frame.
- description: |
libdeth 1.0.0 binary is not compatible with libdeth 2.0.0; recompile against the
new SDK before switching.
Notes
- Strings NOT case sensitive; lowercase auto-uppercased. Avoid accented characters on UTF-8 systems (multi-byte).
- STRINGS
<CR>,<LF>,<TAB>decoded as ASCII 0x0D, 0x0A, 0x09. Domintell auto-trims leading/trailing SPACE. - Light Protocol strings take priority over user-defined ASCII strings — if a "string" link in Domintell2 matches a Light Protocol mnemonic (e.g.
BIR000B4B-1), it will be decoded as Light Protocol and the user link will not fire. - Avoid >100 "string" links on one input; the diagnostic function will surface a WARNING.
- DETH02 reply latency: 5–100 ms depending on frame length and bus load.
- DOMINTELL information message
!! PLEASE UPGRADE DRS23202 FIRMWARE ≥ NNand!! PLEASE UPGRADE DETH02 FIRMWARE ≥ NNindicates incompatible firmware vs. master module OS version; also triggered if DETH02/DRS23202 receives an unsupported module-type status. - Light Protocol
&is the reserved character for multi-message concatenation and as the inter-message gap alternative (≥ 25 ms). - DRS23202 has fixed 57600 8-N-1; DRS23201 allows baud selection (1200/2400/4800/9600/19200/38400/57600).
- DRS23202 Light Protocol requires configuration software ≥ 1.19.11 and firmware ≥ v15 if used in installations with other DRS23202/DETH02 modules.
Provenance
source_domains:
- pro.mydomintell.com
- pro2.mydomintell.com
source_urls:
- https://pro.mydomintell.com/share/manual/DETH0x/DS_RS232_ETH_Interfaces_v1_27_02.pdf
- https://pro2.mydomintell.com/share/manual/DETH02-DRS23202/DS_RS232_ETH_Interfaces_v1_19_17.pdf
retrieved_at: 2026-07-03T08:52:02.971Z
last_checked_at: 2026-07-07T11:35:03.625Z
Verification Summary
verdict: verified
checked_at: 2026-07-07T11:35:03.625Z
matched_actions: 70
action_count: 70
confidence: medium
summary: "All 70 spec actions matched literally in source; transport fully verified; coverage is complete. (8 unresolved item(s) noted in Known Gaps.)"
Known Gaps
- "source documents the DRS2320x / DETH0x gateway family. No module named \"Dmov07\" appears in the source text; the spec is authored against the family-level Light Protocol."
- "firmware version compatibility ranges (v15 DRS23202, v7 DETH02) are stated only for multi-module installations, not as a blanket floor requirement."
- "source enumerates output Light Protocol frames but does not name a single"
- "source does not document a macro/sequencing layer at the protocol surface."
- "source describes the DRS2320x / DETH0x gateway family in general terms but does not name \"Dmov07\" anywhere. Treat the spec as authoritative for the family and assess against actual hardware before publication."
- "source does not provide a Tx/Rx command timing budget beyond the 5–100 ms DETH02 reply range."
- "fault behavior, error-recovery sequences, and watchdog semantics are not documented."
- "percent value encoding for the older `%D00` / `%D01` syntax on SYS Regulation appears inconsistent in the source (mixed zero-padding). Treat values as integers, validate against the actual device."
From the AI4AV catalog (https://ai4av.net) · ODbL-1.0